Land Rover Defender Workshop 1993 Rover Manual

SECTION Body .................................................................. 
SECTION Electrical ........................................................... 
Published by Rover  Technical  Communication 
Publication  Part 
No. LRL0076USA ©1996 Rover Group Limited  

BODY AND ELECTRICAL  CONTENTS 
Section 
Number 
Page 
- Rear  seat cushion ........................................................................\
................................. 1 
- Rear seat squab ........................................................................\
.................................... 1 
- Rear  seat belts ........................................................................\
...................................... 2 
- Side  trim panel...

BODY 
REAR SEAT CUSHION REAR SEAT SQUAB 
Service  repair no - 76.71.26 
Service  repair no - 76.71.24 
Remove  Remove 
1. Release seat cushion stowage  strap. 
2. Remove four bolts  and spring  washers  and lift seat cushion. 
seat  cushion from  pivot brackets. 
3.  Remove  four bolts,  plain washers,  spring 
to body side. 
washers  and nuts.  Detach both pivot  brackets 
from  wheel arch. 
1. Release seat cushion stowage strap and  lower 
2. Slacken two bolts securing  seat squab brackets 
3.  Remove...

BODY 
REAR SEAT BELTS Refit 
Service  repair no - 76.73.18 
Remove 
6. Reverse  removal procedure, ensuring  seat belt 
fixing bolts are  tightened to 32 
Nm (24 Ibf.ft). 
1. Release  belt straps from buckles on  both seats. 
2. Raise  both seat cushions  and secure  with 
stowage straps. 
3. Unscrew bolt  and remove bracket  and inner seat 
belt straps. 
4. Unscrew  bolt and remove rear seat buckle strap 
from wheel  arch. 
5. Unscrew bolt and remove front seat  buckle strap 
from  interior roll
-over...

BODY 
SIDE TRIM PANEL Refit 
Service  repair no 
- 76.13.70 
Remove 
10.  Fit new  spring  clips to the  three  brackets  on top 
11.  Carefully  pull trim  panel  behind interior roll
-over 
12.  Align  trim panel, ensuring  it is  correctly 
13.  Locate trim  panel spring  clips on  inner cant  rail 
edge of 
side trim panel. 
bar.  positioned  around side window. 
and  press firmly  down to secure top edge  of trim 
panel. 
support bracket  with body  side fixing  holes and 
secure  with four bolts...

BODY 
6. Remove 2 tom bolts and nuts from  both sides 
and  detach  centre section  of roll
-over  bar 
assembly 
. 
7. Remove  torx bolt, from  both sides,  securing 
roll
-over  bar to body  side mounting brackets. 
8. Remove  3 bolts  and washers,  from both sides, 
securing  lower roll
-over bar brackets  to front  of 
wheelarch. 
9. Remove 2 tom bolts  and washers, from  both 
sides, securing  roll
-over bar upper  mountings  to 
roof  fixing  brackets  and carefully  lower complete 
assembly to...

BODY 
Refit REAR END TRIM PANEL 
13. Supporting  from  both sides, position  roll-over bar 
on  the floor  in front  of wheelarches. 
14.  Secure front  seat belt inertia reels  and rear seat 
belts to roll
-over  bar mountings.  Tighten bolts to 
32Nm 
(24 Ibf.ft). 
15.  Raise  roll
-over bar assembly  and secure  to roof 
mounting brackets. Tighten bolts to  45  Nm 
(33 
Ibf.ft). 
16.  Secure  roll
-over bar to wheelarches.  Tighten 
bolts to  45 Nm  (33 Ibf.ft). 
17.  Secure  roll
-over bar to  body...

BODY 
CUBBY BOX REAR GRAB  HANDLE 
Service  repair 
no - 76.25.04 
Remove  Remove  Service repair 
no - 76.58.35 
1. 
Remove  radio/cassette player. 
2. Open cubby  box lid and remove  two caps 
3.  Remove  fixing bolts  and washers. 
4.  Remove 
2 screws  and lift cup holder from cubby 
box. 
5. Unscrew  two bolts securing  front of cubby  box to 
floor  mounting. 
6. Lift cubby  box and  unthread  radio/cassette 
player leads through cubby  box base. 
7. Remove cubby  box.  1. 
Carefully  prise top and...

BODY 
REAR END LINING REAR 
SPEAKER  PANEL 
Service  repair 
no - 76.64.12 
Remove  Remove  Service 
repair no - 76.13.13 
1. Remove rear  end trim panel. See this Section. 
2.  Remove  rear grab  handles.  See this Section. 
3.  Carefully  prise out 6 trim studs securing  rear end 
4.  Remove rear end  lining. 1. Raise seat cushion and fit  stowage strap. 
2. Remove  rear end trim  panel.  See this Section. 
3.  Remove  rear speaker.  See Electrical. 
4. Peel back carpet  and remove  two screws...

BODY 
5. Remove rear interior  lamp. See Electrical 
7. Carefully prise  out 5 trim  studs securing rear and 
front  headlining  to roof  mounting brackets. 
8. Release  front comers  of headlining  from cant 
rail,  on both  sides. 
9. Pull headlining forwards  sufficiently to clear rear 
end  lining  mounting  brackets. 
10. Release rear corners  of headlining  from cant rail, 
on both  sides. 
11 . Lower rear headlining  from roof and  remove from 
vehicle. 
NOTE:  Take care not to bend  headlining...