Land Rover Defender V8i Workshop Supplement Rover Manual
Here you can view all the pages of manual Land Rover Defender V8i Workshop Supplement Rover Manual. The Land Rover manuals for Automobile are available online for free. You can easily download all the documents as PDF.
Page 71
10MAINTENANCE 14 MAINTENANCE RENEW FUEL FILTER WARNING: Ensure that fuel handling precautions given in Section 01 - Introduction are strictly adhered to when carrying out following instructions. See INTRODUCTION, Information, Fuel Handling Precautions WARNING: The spilling of fuel is unavoidable during this operation. Ensure that all necessary precautions are taken to prevent fire and explosion. The fuel line filter is located on RH chassis side member forward of the rear wheel arch. 1.Disconnect battery...
Page 72
MAINTENANCE 15 MAINTENANCE CARRY OUT ROAD OR ROLLER TEST WARNING: Two wheel roller tests must be restricted to 8 mph (5km/hour). The propeller shaft to the wheels NOT on the rolling road must be disconnected, and the differential lock engaged. For details of dynamometer testing. See INTRODUCTION, Information, Dynamometer Testing Check following items: 1.Inhibitor switch only operates in P and N. 2.Engine for excessive noise. 3.Automatic gear selection/shift speeds. 4.Gear selection/noise - high/low...
Page 73
Page 74
MAINTENANCE 1 SPECIFICATIONS, TORQUE TORQUE SETTINGS Nm lbf.ft Road wheel nuts 130.............................................................. 95 Spark plugs 20...................................................................... 15 Automatic gearbox drain plug 10.......................................... 8 Transfer box drain/filler plugs 30........................................... 22 Fuel filter hose/pipe unions 30.............................................. 22 Steering box drop arm nut...
Page 75
Page 76
12 - ENGINE CONTENTS Page 4.0 V8i REPAIR CRANKSHAFT REAR OIL SEAL 1......................................................................... DRIVE PLATE 2...................................................................................................... ROCKER SHAFT RENEW 3................................................................................... OIL SUMP 3............................................................................................................ ROCKER COVER GASKET - LEFT...
Page 77
Page 78
4.0 V8i 1 REPAIR CRANKSHAFT REAR OIL SEAL Service repair no - 12.21.20 Remove 1.Disconnect battery negative lead. 2.Remove drive plate. See ENGINE 4.0 V8, Repair, Drive Plate 3.Remove oil seal from location. CAUTION: Do not damage seal location or running surface on crankshaft.Refit 4.Ensure both seal location and running surface on crankshaft are clean. 5.Ensure mating faces of flywheel and crankshaft are clean. 6.Lubricate seal guideLRT-12-095with clean engine oil. Position over crankshaft boss....
Page 79
12ENGINE 2 REPAIR DRIVE PLATE Service repair no - 12.53.13 Remove 1.Remove gearbox and transfer box assembly. See AUTOMATIC GEARBOX, Repair, gearbox and transfer box assembly 2.Remove 4 clamp ring bolts. Collect clamp ring. 3.Remove flexible drive plate/starter ring gear assembly from hub aligner. 4.Remove 6 screws from hub aligner. Remove hub aligner from crankshaft. 5.Check drive plate for distortion or cracks. Check starter ring gear for chipped or broken teeth. If either component shows signs of...
Page 80
4.0 V8i 3 REPAIR ROCKER SHAFT RENEW Service repair no - 12.29.29 Remove 1.Disconnect battery negative lead. 2.Remove RH or LH rocker covers. See ENGINE 4.0 V8, Repair, rocker cover - right hand or. See ENGINE 4.0 V8, Repair, rocker cover - left hand 3.Loosen four rocker shaft fixings. 4.Remove rocker shaft assembly. NOTE: Each rocker shaft is notched at ONE end. Notch must be uppermost and towards front of engine on right hand side, towards rear on left hand side. Refit 5.Clean rocker pedestal locations...