Land Rover Defender 1999 2002my Workshop Supplement Body Repair 3rd Edition Rover Manual

18ENGINE MANAGEMENT SYSTEM
28
DESCRIPTION AND OPERATION OPERATION
Engine Management
The ECM controls the operation of the engine using stored information within its memory. This guarantees
optimum performance from the engine in terms of torque delivery, fuel consumption and exhaust emissions in all
operating conditions, while still giving optimum driveability.
The ECM will receive information from its sensors under all operating conditions, especially during:
Cold starting.
Hot starting.
Idle.
Wide...

ENGINE MANAGEMENT SYSTEM
1
REPAIR ENGINE CONTROL MODULE (ECM)
Service repair no - 18.30.03
Remove
1.Release fixings and remove battery cover.
2.Disconnect battery negative lead.
3.Remove RH seat cushion, release clip and
remove ECM access panel.
4.Remove 3 bolts, release ECM and disconnect 2
multiplugs. Remove ECM.
Refit
5.Position new ECM and connect multiplugs.
6.Fit ECM and tighten bolts.
7.Fit access panel and RH seat cushion.
8.Reconnect battery negative lead.
9.Fit battery cover and secure with...

18ENGINE MANAGEMENT SYSTEM
2
REPAIR SENSOR - CRANKSHAFT SPEED AND POSITION
(CKP)
Service repair no - 18.30.12
Remove
1.Disconnect CKP sensor multiplug.
2.Remove bolt, remove CKP sensor from gearbox
housing and discard’O’ring.
3.If fitted, collect spacer.
Refit
4.Clean gearbox housing and CKP sensor.
5.If fitted, refit spacer.
6.Fit new’O’ring, position CKP sensor to gearbox
housing and tighten bolt to10 Nm (7 lbf.ft).
7.Connect sensor multiplug. 

19 - FUEL SYSTEM
CONTENTS
Page
DESCRIPTION AND OPERATION
COMPONENT LOCATION 1...................................................................................
DESCRIPTION 2.....................................................................................................
FUEL PUMP AND FUEL GAUGE SENDER 3........................................................
FUEL PRESSURE REGULATOR 5........................................................................
INJECTORS...

FUEL SYSTEM
1
DESCRIPTION AND OPERATION COMPONENT LOCATION
1.HP stage
2.LP stage
3.Filters
4.Jet pump
5.Fuel pump and fuel gauge sender unit
6.LP return connection
7.LP feed connection8.HP feed connection
9.Air bleed connection
10.Fuel filter
11.Water sensor
12.Fuel cooler
13.Fuel pressure regulator
14.Electronic Unit Injectors 

19FUEL SYSTEM
2
DESCRIPTION AND OPERATION DESCRIPTION
General
The fuel delivery system comprises a fuel tank, fuel pump, fuel pressure regulator, five injectors and a fuel filter.
The system is controlled by the ECM, which energises the fuel pump relay and controls the operation and timing
of each injector solenoid.
Unlike other Diesel engines, the Td5 has no injection pump. The diesel direct injection system receives fuel at
pressure from a two stage fuel pump located in the fuel tank. The system...

FUEL SYSTEM
3
DESCRIPTION AND OPERATION FUEL PUMP AND FUEL GAUGE SENDER
1.Fuel burning heater feed pipe (not used)
2.Air bleed connection (natural)
3.HP feed connection (green)
4.LP feed connection (blue)
5.LP return connection (black)
6.Pump feed pipe.
7.Spring
8.Fuel gauge sender unit9.Swirl pot
10.Gauze filter
11.Fuel gauge sender float
12.Electrical connections
13.HP/LP two stage pump
14.Pump LP return pipe
15.Electrical connector
The fuel pump is a self priming, wet type, two stage pump, which is...

19FUEL SYSTEM
4
DESCRIPTION AND OPERATION Fuel Pump
The fuel pump assembly comprises a top cover which locates the electrical connector, and four fuel pipe
couplings. The top cover is attached to a plastic cup shaped housing and retained on three sliding clips. Two coil
springs are located between the cover and the housing and ensure that the fuel pump remains seated positively at
the bottom of the tank when installed.
The housing locates the two stage fuel pump and also the fuel gauge sender unit. The...

FUEL SYSTEM
5
DESCRIPTION AND OPERATION FUEL PRESSURE REGULATOR
NOTE: Non EU3 Model illustrated.
1.Gasket
2.Housing
3.Bolt
4.Fuel feed union and pipe
5.Fuel return union and hose
6.Fuel temperature sensor
7.Bonded seal8.’O’ring
9.Circlip
10.Fuel pressure regulator
11.’O’ring
12.’O’ring
13.Gauze filter
The fuel pressure regulator is located in a cast alloy housing which is attached to the rear right hand corner of the
cylinder head with three flanged bolts and sealed with a metal gasket. Two ports in the...