LaCie 120 Users Manual

2. Your LaCie 120 Monitor
page 11
LaCie 120 Monitor
User’s Manual
2.2. Rear View 
On/off switch
Power Supply Connector
DVI port
VGA port1
2
3
4
2
3
1
4
 

3. Using Your LaCie 120 Monitor
page 12
LaCie 120 Monitor
User’s Manual
3. Setting Up Your LaCie 120 Monitor
3.1. Height, Tilt, and Swivel Adjustment
For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitors angle to your 
own preference. 
Hold the stand so you do not topple the monitor when you change the monitors angle. 
1
Important Info:
• Do not touch the LCD screen when making the adjustments above. It may cause damage or break the LCD screen.
• Careful...

4. External Controls
4. External Controls
page 13
LaCie 120 Monitor
User’s Manual
1
5
6
7
Important Info:
To lock the OSD, press and hold the MENU button while the monitor is off and then press power button to turn the
monitor on.
To un-lock the OSD - press and hold the MENU button while the monitor is off and then press power button to turn
the monitor on.
3
4
2
SOURCE - Select the VGA or DVI function.
Auto -  When OSD menu is in active status, this button
will act as EXIT-KEY (EXIT OSD menu) or go back...

5. How to Adjust a Setting
page 14
LaCie 120 Monitor
User’s Manual
5. How To Adjust a Setting
1. Press the MENU-button to activate the OSD window. 
2. Press  or       to navigate through the functions.
Once the desired function is highlighted, press the MENU-
button  to activate it.  If the function selected has a sub-
menu, press      or       again to navigate through the
sub-menu functions.  Once the desired function is high-
lighted, press MENU-button to activate it.  
3. Press      or       to...

5. How to Adjust a Setting
page 15
LaCie 120 Monitor
User’s Manual
Main Menu Item Sub Menu Item Description
Color Temp.
Input Select 
OSD Setup
Language
Information
Reset
EXITC1
C2
sRGB
USER
Analog or digital
H. Position
V. Position
OSD Timeout
English, Deutsch,
Français, Español,
Italiano, or Chinese
Yes/NoRecall C1 Temperature from EEPROM
Recall C2 Temperature from EEPROM
Recall sRGB Temperature from EEPROM
Red Gain from Digital-register.
Green Gain Digital-register.
Blue Gain from Digital-register....

6. Troubleshooting
page 16
LaCie 120 Monitor
User’s Manual
Possible Solutions
• Make sure power switch is in ON position.
• Check power cord connections.
• Check if PC system is Plug & Play
• Check if Video Card system is Plug & Play
• Check if D-15 plug pin of video cable is bent
• Make sure monitors drivers are installed.
• Adjust contrast and brightness controls.
• Move electrical devices that may cause interference.
• POWER switch must be ON
• Video card must be snugly fit into position.
• Check...

6. Troubleshooting
page 17
LaCie 120 Monitor
User’s Manual
Possible Solutions
• Make sure signal cable is properly connected. If loose, tighten screws.
• Check signal cable connection pins for damage.
Your computer has been set to an unsuitable display mode. Set the computer to a display mode
given in the preset display modes table.  The Problem
ERROR MESSAGE: Cable
not Connected
ERROR MESSAGE: Input
not Supported
 

7. Preset Display Modes
STANDARD RESOLUTION HORIZONTAL FREQUENCY(KHZ) VERTICAL FREQUENCY(HZ)
IBM DOS 720 _ 400 31.47 70.0
VGA 640 _ 480 31.47 60.0
640 _ 480 37.50 75.0
SVGA 800 _ 600 37.879 60.0
800 _ 600 46.875 75.0
VESA XGA 1024 _ 768 48.363 60.0
1024 _ 768 56.476 70.0
1024 x 768 60.02 75.0
1024 x 768 48.780 60.0
1024 x 768 60.241 75.0
SXGA 1280 _ 1024 64.00 60.0
1280 _ 1024 80.00 75.0
UXGA 1600 x 1200 75.00 60.0 
7. Preset Display Modes
page 18
LaCie 120 Monitor
User’s Manual
Important Info:• LCD...

8. Connector Pin Assignment 
page 19
LaCie 120 Monitor
User’s Manual
8. Connector Pin Assignment
PIN # DESCRIPTION PI N # DESCRIPTION
1. Video-Red 9. +5V
2. Video-Green 10. Detect Cable
3. Video-Blue 11. NC
4. NC 12. DDC-Serial data
5. Ground 13. H-sync
6. GND-R 14. V-sync
7. GND-G 15. DDC-Serial clock
8. GND-B
PIN # DESCRIPTION PI N # DESCRIPTION
1. TMDS Data 2- 13. TMDS Data 3+
2. TMDS Data 2+ 14. +5V Power
3. TMDS Data 2/4 Shield 15. Ground(for+5V)
4. TMDS Data 4- 16. Hot Plug Detect
5. TMDS Data 4+...

9. Contacting Customer Support
page 20
LaCie 120 Monitor
User’s Manual
9. Contacting Customer Support
Before You Contact Technical Support
1) Read the manuals and review the Troubleshootingsection.
If you have asked yourself all of the pertinent questions in the troubleshooting checklist, and you still cant get your LaCie
monitor to work properly, contact us via the provided Web link. Before contacting us, make sure that you are in front of your
computer and that you have the following information on...