LaCie 120 Users Manual
Have a look at the manual LaCie 120 Users Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 9 LaCie manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
2. Your LaCie 120 Monitor page 11 LaCie 120 Monitor User’s Manual 2.2. Rear View On/off switch Power Supply Connector DVI port VGA port1 2 3 4 2 3 1 4
3. Using Your LaCie 120 Monitor page 12 LaCie 120 Monitor User’s Manual 3. Setting Up Your LaCie 120 Monitor 3.1. Height, Tilt, and Swivel Adjustment For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitors angle to your own preference. Hold the stand so you do not topple the monitor when you change the monitors angle. 1 Important Info: • Do not touch the LCD screen when making the adjustments above. It may cause damage or break the LCD screen. • Careful attention is required not to catch your fingers or hands when making the adjustments above.
4. External Controls 4. External Controls page 13 LaCie 120 Monitor User’s Manual 1 5 6 7 Important Info: To lock the OSD, press and hold the MENU button while the monitor is off and then press power button to turn the monitor on. To un-lock the OSD - press and hold the MENU button while the monitor is off and then press power button to turn the monitor on. 3 4 2 SOURCE - Select the VGA or DVI function. Auto - When OSD menu is in active status, this button will act as EXIT-KEY (EXIT OSD menu) or go back to the previous menu. When OSD menu is in off status, press this button for 2 seconds to activate the Auto Adjustment function. The Auto Adjustment function is used to set the HPos, VPos, Clock and Focus. (Precise auto adjustment available only in analog mode.) Brightness - adjust brightness or function adjust Contrast - adjust contrast or function adjust Menu- active OSD or function adjust Power Indicator - notes status of monitor: BLUE - on, ORANGE - standby, RED - of f Power Button - press to power on or power off monitor
5. How to Adjust a Setting page 14 LaCie 120 Monitor User’s Manual 5. How To Adjust a Setting 1. Press the MENU-button to activate the OSD window. 2. Press or to navigate through the functions. Once the desired function is highlighted, press the MENU- button to activate it. If the function selected has a sub- menu, press or again to navigate through the sub-menu functions. Once the desired function is high- lighted, press MENU-button to activate it. 3. Press or to change the settings of the selected function. 4. To exit and save, select the exit function. If you want to adjust any other function, repeat steps 2-3. 5.1 Descriptions for function control LEDS Main Menu Item Sub Menu Item Description Luminance Image setup Image positionContrast Brightness Focus Clock H. position V. positionContrast from Digital-register. Backlight adjustment Adjust picture phase to reduce horizontal line noise Adjust picture phase to reduce vertical line noise. Adjust horizontal picture Adjust vertical picture
5. How to Adjust a Setting page 15 LaCie 120 Monitor User’s Manual Main Menu Item Sub Menu Item Description Color Temp. Input Select OSD Setup Language Information Reset EXITC1 C2 sRGB USER Analog or digital H. Position V. Position OSD Timeout English, Deutsch, Français, Español, Italiano, or Chinese Yes/NoRecall C1 Temperature from EEPROM Recall C2 Temperature from EEPROM Recall sRGB Temperature from EEPROM Red Gain from Digital-register. Green Gain Digital-register. Blue Gain from Digital-register. Select input signal from analog (D-Sub) or digital (DVI) source Adjust the horizontal position of the OSD. Adjust the vertical position of the OSD. Adjust the OSD timeout. Set OSD display language to desired lan- guage, (EN, DE, FR, ES, IT, simplified Chinese) Show the resolution, H/V frequency and input port of current input timing. Ye s—Clear each old status of Auto-config- uration and set the color temperature to Cool.No— Do not execute reset, return to main menu EXIT OSD
6. Troubleshooting page 16 LaCie 120 Monitor User’s Manual Possible Solutions • Make sure power switch is in ON position. • Check power cord connections. • Check if PC system is Plug & Play • Check if Video Card system is Plug & Play • Check if D-15 plug pin of video cable is bent • Make sure monitors drivers are installed. • Adjust contrast and brightness controls. • Move electrical devices that may cause interference. • POWER switch must be ON • Video card must be snugly fit into position. • Check cable connection. • Inspect pins on cable to be sure all are straight. • Make sure computer is operational by typing the CAPS LOCK key while observing CAPS LOCK LED. The LED should be operational. Inspect the video cable to be sure none of the pins are bent. Adjust pixel frequency (CLOCK) and FOCUS or press hot-key (AUTO-key). Adjust RGB color or select color temperature. The Problem Power LED not on No Plug & Play Fuzzy Picture Picture bounces of there is a wave pattern The POWER LED is on but there is no video or picture, Missing RED, GREEN or BLUE Screen Image not centered Picture has defects, for example white does not look white. 6. Troubleshooting
6. Troubleshooting page 17 LaCie 120 Monitor User’s Manual Possible Solutions • Make sure signal cable is properly connected. If loose, tighten screws. • Check signal cable connection pins for damage. Your computer has been set to an unsuitable display mode. Set the computer to a display mode given in the preset display modes table. The Problem ERROR MESSAGE: Cable not Connected ERROR MESSAGE: Input not Supported
7. Preset Display Modes STANDARD RESOLUTION HORIZONTAL FREQUENCY(KHZ) VERTICAL FREQUENCY(HZ) IBM DOS 720 _ 400 31.47 70.0 VGA 640 _ 480 31.47 60.0 640 _ 480 37.50 75.0 SVGA 800 _ 600 37.879 60.0 800 _ 600 46.875 75.0 VESA XGA 1024 _ 768 48.363 60.0 1024 _ 768 56.476 70.0 1024 x 768 60.02 75.0 1024 x 768 48.780 60.0 1024 x 768 60.241 75.0 SXGA 1280 _ 1024 64.00 60.0 1280 _ 1024 80.00 75.0 UXGA 1600 x 1200 75.00 60.0 7. Preset Display Modes page 18 LaCie 120 Monitor User’s Manual Important Info:• LCD monitors have a fixed size & number of pixels. Due to this, an interpolation is necessary to operate the monitor in a resolution below it’s native resolution which may slightly degrade the display quality. Therefore, it is highly recommended to operate the monitor at it’s native resolution of 1600 x 1200 @ 60Hz.
8. Connector Pin Assignment page 19 LaCie 120 Monitor User’s Manual 8. Connector Pin Assignment PIN # DESCRIPTION PI N # DESCRIPTION 1. Video-Red 9. +5V 2. Video-Green 10. Detect Cable 3. Video-Blue 11. NC 4. NC 12. DDC-Serial data 5. Ground 13. H-sync 6. GND-R 14. V-sync 7. GND-G 15. DDC-Serial clock 8. GND-B PIN # DESCRIPTION PI N # DESCRIPTION 1. TMDS Data 2- 13. TMDS Data 3+ 2. TMDS Data 2+ 14. +5V Power 3. TMDS Data 2/4 Shield 15. Ground(for+5V) 4. TMDS Data 4- 16. Hot Plug Detect 5. TMDS Data 4+ 17. TMDS Data 0- 6. DDC Clock 18. TMDS Data 0+ 7. DDC Data 19. TMDS Data 0/5 Shield 8. NC 20. TMDS Data 5- 9. TMDS Data 1- 21. TMDS Data 5+ 10. TMDS Data 1+ 22. TMDS Clock Shield 11. TMDS Data 1/3 Shield 23. TMDS Clock + 12. TMDS Data 3- 24. TMDS Clock - 24 - Pin Color Display Signal Cable 24 - Pin Color Display Signal Cable 15 - Pin Color Display Signal Cable 15 - Pin Color Display Signal Cable
9. Contacting Customer Support page 20 LaCie 120 Monitor User’s Manual 9. Contacting Customer Support Before You Contact Technical Support 1) Read the manuals and review the Troubleshootingsection. If you have asked yourself all of the pertinent questions in the troubleshooting checklist, and you still cant get your LaCie monitor to work properly, contact us via the provided Web link. Before contacting us, make sure that you are in front of your computer and that you have the following information on hand: • Your LaCie monitor’s serial number • Operating system (Mac OS or Windows) and version • Computer brand and model • Graphics board brand and model • Type of video signal used (analog/VGA/D-sub or digital/DVI connector)