Kyocera KM 3650w User Manual

Chapter 3     Error Correction  3-18
3. 1. 3. 5     In Power Save Mode 
 
When “In Power Save Mode.” is displayed, KM-3650w is in the Power Save Mode to save the 
power consumption. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
(1)  The Power Save Mode works automatically if you make no operation for the time  
      specified in advance. 
      The machine ceases controlling the temperature of Fuser Unit completely to save the  
      power consumption. (Power Save Mode...

Chapter 3     Error Correction  3-19
3. 2     Service Call Errors 
 
 
You will note an error message “A significant error occurred. Call the service” on the operation 
panel if the machine has the fatal error. 
At this time one of the following sub messages is displayed also. 
 
 Counter Error 
 Cutter Error 
  Developer Motor Error 
 FPGA Error 
  Fuser Low temp 
  Fuser Motor Error 
  Fuser Over temp 
 HV Charger Error 
  License Key Error 
 Main Motor Error 
 
 
 
 
 
 
PLEASE CALL YOUR TRAINED...

Chapter 4     Maintenance  4-1  
 
 
 
Chapter 4 
 
Maintenance 
 
 
Page 
4. 1     Cleaning of Each Part         4-  2 
   4. 1. 1     Scanner Unit                  4-  2 
   4. 1. 2     Print Engine                  4-  4 
   4. 1. 3     Operation Panel                  4-  6 
 
Downloaded From ManualsPrinter.com Manuals 

Chapter 4     Maintenance  4-2
4. 1     Cleaning of Each Part 
 
 
4. 1. 1     Scanner Unit 
 
Clean each Scan Glass, Feeding Rollers and Guide Plates once per a week, as the scan/copy 
image may become defective if these parts are dirty. 
 
 1.  Confirm that the machine is turned off. 
 
 
 2.  Open the Scanner Unit pulling up the Levers (1). 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 3.  Wipe each Scan Glass (2) and Feeding Rollers (3) with a soft cloth. 
      Use the neutral detergent mixed with 50%...

Chapter 4     Maintenance  4-3  4.  Wipe both the Upper Guide Plate (4) and the Lower Guide Plate (5) with a soft dry cloth. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 5.  Move the Scanner Unit a little to the rear side to unlock, and then close it. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
4
5
Downloaded From ManualsPrinter.com Manuals 

Chapter 4     Maintenance  4-4
4. 1. 2     Print Engine 
 
Clean each Guide Film and Guide Plate once per a week, as the toner or paper dust may 
accumulates on such part which may result in a defective print image. 
 
 1.  Confirm that the machine is turned off. 
 
 
 2.  Open the Engine Unit pulling up the Engine Unit Open Levers (1). 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 3.  Wipe each Guide Film (2) and Guide Plate (3) with a soft dry cloth to remove the toner or paper  
     dust....

Chapter 4     Maintenance  4-5  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 4.  Close the Engine Unit. 
 
 
 
 
 
 
 
 
 
 
 
 
         NOTE 
 
(1)  Photoconductive Drum (large green cylinder) right above the Guide Film. 
      You need to replace the Drum if damaged, as it is a very important part in creating the  
      print image. 
 
      Be careful about the following matters. 
 
         a.)  Do not touch the drum.  
               If you put your...

Chapter 4     Maintenance  4-6
4. 1. 3     Operation Panel 
 
Clean the Operation Panel once per a week. 
 
 1.  Confirm that the machine is turned off. 
 
 
 2.  Wipe the Operation Panel with a dry cloth. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
         NOTE 
 
Do not use water, alcohol, organic solvent and glass cleaner for the cleaning. 
Downloaded From ManualsPrinter.com Manuals 

For best results and machine performance, we re commend that you use only our original supplies for 
your products.
Downloaded From ManualsPrinter.com Manuals 

Downloaded From ManualsPrinter.com Manuals