Kyocera KM 3060 User Manual

							Troubleshooting 
OPERATION GUIDE6-21
6
Paper Feed Unit
Follow the steps below to clear paper jams in the paper feed unit.
1Pull up left cover 1 lever and 
open the left cover.
2Remove the jammed paper.
If the paper tears, remove 
every loose scrap from inside 
the machine.
3Open front cover.
4Turn the lower green knob 
(A1) clockwise.
Downloaded From ManualsPrinter.com Manuals 
						

							Troubleshooting 
6-22OPERATION GUIDE
5Remove the jammed paper.
If you cannot remove the 
paper, proceed with the next 
step.
6Pull out paper feed unit (A2).
7Open paper feed unit cover 
(A3) and remove the jammed 
paper.
8Push paper feed unit (A2) back in place, and close the front cover.
9Press the specified position to 
close left cover 1.
Downloaded From ManualsPrinter.com Manuals 
						

							Troubleshooting 
OPERATION GUIDE6-23
6
Built-in Finisher (optional)
If paper is jammed in the optional built-in finisher, use the procedure below 
to remove the paper.
1Remove any paper left in the finisher output slot.
2Remove the output tray.
3Pull up left cover 1 lever and 
open left cover 1.
4Remove the jammed paper.
5Press the indicated position to 
close left cover 1.
2
1
Downloaded From ManualsPrinter.com Manuals 
						

							Troubleshooting 
6-24OPERATION GUIDE
6Re-attach the output tray.
7Turn the lever to lower the 
finisher process tray.
8Remove any paper from the 
tray.
9Raise the finisher process tray.
1
2
Downloaded From ManualsPrinter.com Manuals 
						

							Troubleshooting 
OPERATION GUIDE6-25
6
Optional Document Processor
Follow the steps below to clear paper jams in the optional document 
processor.
1Remove the original from the 
original tray.
2Open the document processor 
top cover.
3Remove the jammed original.
If the original tears, remove 
every loose scrap from inside 
the machine.
4Lift up paper feed unit A.A
Downloaded From ManualsPrinter.com Manuals 
						

							Troubleshooting 
6-26OPERATION GUIDE
5Remove the jammed original.
If the original tears, remove every loose scrap from inside the machine.
6Remove the original by turning 
the dial C as shown in the 
figure.
7Put paper feed unit A back in its original place and close the document 
processor top cover.
8Reload the originals on the document processor tray.
Optional Document Finisher
If a misfeed occurs in the optional document finisher, refer to the respective 
Operation Guides to clear the jam.
Optional Job Separator (optional)
Follow the steps below to clear paper jams in the optional job separator.
1If jammed paper is seen 
through the paper output slot 
of the job separator, pull it 
toward your side to remove it.
If the paper tears, remove 
every loose scrap from inside 
the machine.
2Pull up left cover 1 lever and 
open left cover 1.
C
Downloaded From ManualsPrinter.com Manuals 
						

							Troubleshooting 
OPERATION GUIDE6-27
6
3Remove the jammed paper.
If the paper tears, remove 
every loose scrap from inside 
the machine.
4Press the indicated position to 
close left cover 1.
Downloaded From ManualsPrinter.com Manuals 
						

							Troubleshooting 
6-28OPERATION GUIDE
Downloaded From ManualsPrinter.com Manuals 
						

							OPERATION GUIDEAppendix-1
Appendix
• Character Entry Method .................................. Appendix-2
• Paper ............................................................... Appendix-6
• Specifications .................................................. Appendix-7
Downloaded From ManualsPrinter.com Manuals 
						

							 
Appendix-2OPERATION GUIDE
Character Entry Method
To enter characters for a name, use the on-display keyboard in the touch 
panel following the steps as explained below.
NOTE: QWERTY, QWERTZ and AZERTY are available as keyboard 
layouts the same as a PC keyboard. Press the System Menu, [Common 
Settings] and then [Change] of Keyboard to choose desired layout. 
QWERTY layout is used here as an example. You may use another layout 
following the same steps. 
Entry Screens
Lower-case Letter Entry Screen
No. Display/Key Description
1 Display Displays entered characters.
2 Limit Display Displays maximum number of characters.
3 Cursor Key Press to move the cursor on the display.
4 [Backspace] Press to delete a character to the left of the 
cursor.
5 Keyboard Press a character to enter.
6 [Upper-case] Press to use upper-case letters.
7 [Lower-case] Press to use lower-case letters,
8 [No./Symbol] Press to enter numbers and symbols.
9 [Space] Press to insert a space.
Us e t he keyboard t o ent er.
Backspace
Upper - c as eLower-cas eNo ./Sy m bol Spac e
Cancel OK Pat h
Input :   c harac t ers Limit:     characters
0 1261
2
4
5
6
7891011
3
Downloaded From ManualsPrinter.com Manuals