Kyocera FS 4020DN User Manual
Here you can view all the pages of manual Kyocera FS 4020DN User Manual. The Kyocera manuals for Printer are available online for free. You can easily download all the documents as PDF.
Page 51
![Page 51
4-4Connecting and Printing
Changing Network Interface Parameters
This printer supports TCP/IP, TCP/IP (IPv6), NetWare, AppleTalk, IPP,
SSL Server, IPSec protocols, and Security Level. For more information,
refer to the Advanced Operation Guide .
TCP/IP, TCP/IP (IPv6) settings
1
Press [MENU] .
2Press U or V repeatedly until Network > appears.
3Press Z. Each time you press U or V, the selection changes. Refer
to the explanations below when specifying the settings.
Set this item to On when you...](http://img.usermanuals.tech/thumb/2828/37281/w300_Kyocera_FS-4020DN-50.png "Page 51
4-4Connecting and Printing
Changing Network Interface Parameters
This printer supports TCP/IP, TCP/IP (IPv6), NetWare, AppleTalk, IPP,
SSL Server, IPSec protocols, and Security Level. For more information,
refer to the Advanced Operation Guide .
TCP/IP, TCP/IP (IPv6) settings
1
Press [MENU] .
2Press U or V repeatedly until Network > appears.
3Press Z. Each time you press U or V, the selection changes. Refer
to the explanations below when specifying the settings.
Set this item to On when you...")
4-4Connecting and Printing Changing Network Interface Parameters This printer supports TCP/IP, TCP/IP (IPv6), NetWare, AppleTalk, IPP, SSL Server, IPSec protocols, and Security Level. For more information, refer to the Advanced Operation Guide . TCP/IP, TCP/IP (IPv6) settings 1 Press [MENU] . 2Press U or V repeatedly until Network > appears. 3Press Z. Each time you press U or V, the selection changes. Refer to the explanations below when specifying the settings. Set this item to On when you...
Page 52
![Page 52
Connecting and Printing4-5
TCP/IP
This section describes how to enable the TCP/IP protocol.
1If TCP/IP is set to Off, use U or V to select On and press [OK].
2Press Z. Each time you press U or V, the selection changes.
3Display the item you want to set and press [OK]. A blinking question
mark ( ?) appears while you are setting DHCP and Bonjour . A
blinking cursor ( _) appears while you are setting IP Address,
Subnet Mask and Gateway .
4Press U or V to select On or Off as the setting...](http://img.usermanuals.tech/thumb/2828/37281/w300_Kyocera_FS-4020DN-51.png "Page 52
Connecting and Printing4-5
TCP/IP
This section describes how to enable the TCP/IP protocol.
1If TCP/IP is set to Off, use U or V to select On and press [OK].
2Press Z. Each time you press U or V, the selection changes.
3Display the item you want to set and press [OK]. A blinking question
mark ( ?) appears while you are setting DHCP and Bonjour . A
blinking cursor ( _) appears while you are setting IP Address,
Subnet Mask and Gateway .
4Press U or V to select On or Off as the setting...")
Connecting and Printing4-5 TCP/IP This section describes how to enable the TCP/IP protocol. 1If TCP/IP is set to Off, use U or V to select On and press [OK]. 2Press Z. Each time you press U or V, the selection changes. 3Display the item you want to set and press [OK]. A blinking question mark ( ?) appears while you are setting DHCP and Bonjour . A blinking cursor ( _) appears while you are setting IP Address, Subnet Mask and Gateway . 4Press U or V to select On or Off as the setting...
Page 53
![Page 53
4-6Connecting and Printing
TCP/IP (IPv6)
This section describes how to enable the TCP/IP (IPv6) protocol.
1If TCP/IP (IPv6) is set to Off, use U or V to selecto On and
press [OK].
2Press Z. Each time you press U or V, the selection changes.
3Display the item you want to set and press [OK]. A blinking question
mark ( ?) appears while you are setting RA(Stateless) and
DHCPv6 .
4Press U or V to select On or Off as the setting for
RA(Stateless) and DHCPv6 .
5Press [OK].
6Press [MENU] ....](http://img.usermanuals.tech/thumb/2828/37281/w300_Kyocera_FS-4020DN-52.png "Page 53
4-6Connecting and Printing
TCP/IP (IPv6)
This section describes how to enable the TCP/IP (IPv6) protocol.
1If TCP/IP (IPv6) is set to Off, use U or V to selecto On and
press [OK].
2Press Z. Each time you press U or V, the selection changes.
3Display the item you want to set and press [OK]. A blinking question
mark ( ?) appears while you are setting RA(Stateless) and
DHCPv6 .
4Press U or V to select On or Off as the setting for
RA(Stateless) and DHCPv6 .
5Press [OK].
6Press [MENU] ....")
4-6Connecting and Printing TCP/IP (IPv6) This section describes how to enable the TCP/IP (IPv6) protocol. 1If TCP/IP (IPv6) is set to Off, use U or V to selecto On and press [OK]. 2Press Z. Each time you press U or V, the selection changes. 3Display the item you want to set and press [OK]. A blinking question mark ( ?) appears while you are setting RA(Stateless) and DHCPv6 . 4Press U or V to select On or Off as the setting for RA(Stateless) and DHCPv6 . 5Press [OK]. 6Press [MENU] ....
Page 54
![Page 54
Connecting and Printing4-7
3Press Z. Each time you press U or V, the selection changes. Refer
to the explanations below when specifying the settings.
If you are using NetWare, AppleTalk , IPP , SSL Server or
IPSec to connect to a network, you must enter an administrator ID
and press [OK]. The default setting is the numeric part of your
printers model name. If you use FS-2020D, enter 2020.
If you are using NetWare, AppleTalk , IPP , SSL Server or
IPSec to connect to a network, you must...](http://img.usermanuals.tech/thumb/2828/37281/w300_Kyocera_FS-4020DN-53.png "Page 54
Connecting and Printing4-7
3Press Z. Each time you press U or V, the selection changes. Refer
to the explanations below when specifying the settings.
If you are using NetWare, AppleTalk , IPP , SSL Server or
IPSec to connect to a network, you must enter an administrator ID
and press [OK]. The default setting is the numeric part of your
printers model name. If you use FS-2020D, enter 2020.
If you are using NetWare, AppleTalk , IPP , SSL Server or
IPSec to connect to a network, you must...")
Connecting and Printing4-7 3Press Z. Each time you press U or V, the selection changes. Refer to the explanations below when specifying the settings. If you are using NetWare, AppleTalk , IPP , SSL Server or IPSec to connect to a network, you must enter an administrator ID and press [OK]. The default setting is the numeric part of your printers model name. If you use FS-2020D, enter 2020. If you are using NetWare, AppleTalk , IPP , SSL Server or IPSec to connect to a network, you must...
Page 55
![Page 55
4-8Connecting and Printing
Set the Security Level to High .
NetWare
This section explains the procedure for enabling NetWare.
1Enter the administrator ID and password. Then, if NetWare is set to
Off , use U or V to select On and press [OK].
2Press Z.
3Press [OK]. A blinking question mark ( ?) appears. Each time you
press U or V, the selection changes.
4Display the item you want to set and press [OK].
5Press [MENU] . The display returns to Ready.
>Security Level
High
>NetWare >...](http://img.usermanuals.tech/thumb/2828/37281/w300_Kyocera_FS-4020DN-54.png "Page 55
4-8Connecting and Printing
Set the Security Level to High .
NetWare
This section explains the procedure for enabling NetWare.
1Enter the administrator ID and password. Then, if NetWare is set to
Off , use U or V to select On and press [OK].
2Press Z.
3Press [OK]. A blinking question mark ( ?) appears. Each time you
press U or V, the selection changes.
4Display the item you want to set and press [OK].
5Press [MENU] . The display returns to Ready.
>Security Level
High
>NetWare >...")
4-8Connecting and Printing Set the Security Level to High . NetWare This section explains the procedure for enabling NetWare. 1Enter the administrator ID and password. Then, if NetWare is set to Off , use U or V to select On and press [OK]. 2Press Z. 3Press [OK]. A blinking question mark ( ?) appears. Each time you press U or V, the selection changes. 4Display the item you want to set and press [OK]. 5Press [MENU] . The display returns to Ready. >Security Level High >NetWare >...
Page 56
![Page 56
Connecting and Printing4-9
AppleTalk
This section explains the procedure for enabling AppleTalk.
1Enter the administrator ID and password. Then, if AppleTalk is set
to Off , use U or V to select On.
2Press [OK]. A blinking question mark ( ?) appears.
3Press [OK] again.
4Press [MENU] . The display returns to Ready.
IPP
This section explains the procedure for enabling IPP.
1Enter the administrator ID and password. Then, if IPP is set to Off,
use U or V to select On.
2Press [OK]. A...](http://img.usermanuals.tech/thumb/2828/37281/w300_Kyocera_FS-4020DN-55.png "Page 56
Connecting and Printing4-9
AppleTalk
This section explains the procedure for enabling AppleTalk.
1Enter the administrator ID and password. Then, if AppleTalk is set
to Off , use U or V to select On.
2Press [OK]. A blinking question mark ( ?) appears.
3Press [OK] again.
4Press [MENU] . The display returns to Ready.
IPP
This section explains the procedure for enabling IPP.
1Enter the administrator ID and password. Then, if IPP is set to Off,
use U or V to select On.
2Press [OK]. A...")
Connecting and Printing4-9 AppleTalk This section explains the procedure for enabling AppleTalk. 1Enter the administrator ID and password. Then, if AppleTalk is set to Off , use U or V to select On. 2Press [OK]. A blinking question mark ( ?) appears. 3Press [OK] again. 4Press [MENU] . The display returns to Ready. IPP This section explains the procedure for enabling IPP. 1Enter the administrator ID and password. Then, if IPP is set to Off, use U or V to select On. 2Press [OK]. A...
Page 57
![Page 57
4-10Connecting and Printing
SSL Server
This section explains the procedure for enabling SSL Server.
1Enter the administrator ID and password. Then, if SSL Server is
set to Off, use U or V to select On and press [OK].
2Press Z. Each time you press U or V, the selection changes.
3Display the item you want to set and press [OK]. A blinking question
mark ( ?) appears.
4Select On or Off using U or V.
5Press [OK].
6Press [MENU] . The display returns to Ready.
IPSec
This section explains the...](http://img.usermanuals.tech/thumb/2828/37281/w300_Kyocera_FS-4020DN-56.png "Page 57
4-10Connecting and Printing
SSL Server
This section explains the procedure for enabling SSL Server.
1Enter the administrator ID and password. Then, if SSL Server is
set to Off, use U or V to select On and press [OK].
2Press Z. Each time you press U or V, the selection changes.
3Display the item you want to set and press [OK]. A blinking question
mark ( ?) appears.
4Select On or Off using U or V.
5Press [OK].
6Press [MENU] . The display returns to Ready.
IPSec
This section explains the...")
4-10Connecting and Printing SSL Server This section explains the procedure for enabling SSL Server. 1Enter the administrator ID and password. Then, if SSL Server is set to Off, use U or V to select On and press [OK]. 2Press Z. Each time you press U or V, the selection changes. 3Display the item you want to set and press [OK]. A blinking question mark ( ?) appears. 4Select On or Off using U or V. 5Press [OK]. 6Press [MENU] . The display returns to Ready. IPSec This section explains the...
Page 58
Connecting and Printing4-11 Security Level Security Level is primarily a menu used by service personnel for maintenance work. There is no need for customers to use this menu. >Security Level High Downloaded From ManualsPrinter.com Manuals
Page 59
![Page 59
4-12Connecting and Printing
Printing a Network Interface Status Page
You can print out a status page for the network interface. The network
status page shows the network addresses, and other information under
various network protocols about the network interface.
Adjust/Maintenance
Adjust/Maintenance is used to adjust the print quality and to carry out
printer maintenance.
The options available in Adjust/Maintenance are as follows:
•Restart Printer
• Service
1Press [MENU] .
2Press U or V repeatedly...](http://img.usermanuals.tech/thumb/2828/37281/w300_Kyocera_FS-4020DN-58.png "Page 59
4-12Connecting and Printing
Printing a Network Interface Status Page
You can print out a status page for the network interface. The network
status page shows the network addresses, and other information under
various network protocols about the network interface.
Adjust/Maintenance
Adjust/Maintenance is used to adjust the print quality and to carry out
printer maintenance.
The options available in Adjust/Maintenance are as follows:
•Restart Printer
• Service
1Press [MENU] .
2Press U or V repeatedly...")
4-12Connecting and Printing Printing a Network Interface Status Page You can print out a status page for the network interface. The network status page shows the network addresses, and other information under various network protocols about the network interface. Adjust/Maintenance Adjust/Maintenance is used to adjust the print quality and to carry out printer maintenance. The options available in Adjust/Maintenance are as follows: •Restart Printer • Service 1Press [MENU] . 2Press U or V repeatedly...
Page 60
Connecting and Printing4-13 Installing the Printer Driver According to the instructions of the Installation Guide, connect the PC to the printer and turn on them to install the printer driver. For more information on printer driver, refer to the KX Driver User Guide in the CD- ROM. Installing the Printer Driver on Windows PC This section explains how to install the printer driver in Windows Vista. 1Ensure the printer is plugged in and connected to the computers USB or Network port before installing...