Kyocera FS 1320D User Manual

Connecting and Printing3-17
Others Tab
The Others tab enables you to configure the printer settings  shown 
below.
Item Description
Auto sleep Configures the amount of time when the printer 
automatically enters Sleep Mode. Click  Advanced to 
turn Auto sleep On  or Off . 
EcoFuser Enables or disables the EcoFuser. Select  On to 
reduce the power consumption to a minimum by 
turning off the heater of the fixing unit at Sleep Mode. 
The default setting is  On.
Panel lock Locks or unlocks the operation...

3-18Connecting and Printing
Uninstalling Software (Windows PC)
The software can be uninstalled (removed) using the CD-ROM (Product 
Library) supplied with the printer.
1Exit all active software applications.
2Insert the enclosed CD-ROM (Product Library) into the CD-ROM 
drive. In Windows 7, Windows Server 2008 and Windows Vista, the 
user account control window may appear. Click Allow .
3Following the procedure used to install the printer driver, click 
Remove Software. The Kyocera Uninstaller wizard...

Maintenance4-1
4 Maintenance
This chapter explains how to replace the toner container and clean the 
printer
.
General Information 4-2
Toner Container Replacement 4-2
Maintenance Kit Replacement 4-5
Cleaning the Printer 4-6
Prolonged Non-Use and Moving of the Printer 4-9
Downloaded From ManualsPrinter.com Manuals 

4-2Maintenance
General Information
This chapter describes basic maintenance tasks you can perform for the 
printer. You can replace the toner container according to the printers 
status:
Also, the internal parts need periodic cleaning.
Toner Container Replacement
The Toner indicator identifies the toner status at two stages of toner 
usage. 
•When the printer becomes low on toner, the Toner  indicator flashes. 
Note the replacement is not always necessary at this stage. 
• If you ignore the above status...

Maintenance4-3
Replacing the Toner Container
This section explains how to replace the toner container.
1Open the top cover.
2Turn the lock lever to the unlock position. Push the lock lever to the 
position marked by the arrow and pull out the toner container.
CAUTION  Do not attempt to incinerate the Toner 
Container. Dangerous sparks may cause burns.
IMPORTANT During toner container replacement, temporarily move 
storage media and computer supplies (such as floppy disks) away 
from the toner container....

4-4Maintenance
3Take the new toner container out of the toner kit. Shake the new 
toner container at least 5 times as shown in the figure in order to 
distribute the toner evenly inside the container.
4Remove the label from the toner container.
5Install the new toner container in the printer. Push firmly on the top of 
the container at the positions marked PUSH, until you hear a click.
Downloaded From ManualsPrinter.com Manuals 

Maintenance4-5
6Turn the lock lever to the lock position.
7Close the top cover.
Maintenance Kit Replacement
When the machine prints 100,000 pages, a message is printed indicating 
that the maintenance kit should be replaced. The maintenance kit must 
then be replaced immediately. 
To replace the maintenance kit, contact your service technician.
IMPORTANTWhen the waste toner in the drum unit is almost full, 
[Attention]  indicator and  [Toner] indicator are flashing. Replace the 
maintenance kit....

4-6Maintenance
Cleaning the Printer
To avoid print quality problems, the interior of the printer must be 
cleaned with every toner container replacement.
1Open the top cover and front cover.
2Lift the developer unit together with the toner container out of the 
printer.
3Remove the drum unit from the printer by holding the green levers 
with both hands.
Developer 
Unit
Drum 
UnitNoteThe drum unit is sensitive to light. Never expose the 
drum unit to light for more than five minutes.
Downloaded From...

Maintenance4-7
4Place the drum unit flat on a clean, level surface.
5Use a clean, lint free cloth to clean dust and dirt away from the metal 
registration roller.
6On the drum unit, slide the charger cleaner (green) back and forth 2 
or 3 times to clean the charger wire, then return it to its original 
position (CLEANER HOME POSITION ).
7When cleaning is complete, return the drum unit to the original 
position.
IMPORTANTDo not place the drum unit on end.
IMPORTANTTake care not to touch the transfer...

4-8Maintenance
8Return the developer unit to its position, aligning the guides at both 
ends with the slots in the printer. Then, close the front cover and top 
cover.
Downloaded From ManualsPrinter.com Manuals