Kyocera FS 1300D User Manual

							Connecting and Printing3-17
Others Tab
The Others  tab enables you to configure the printer settings  shown 
below.
Item Description
Auto sleep Configures the amount of time when the printer  automatically enters Sleep Mode. Click  Advanced to 
turn  Auto sleep  On or Off. 
EcoFuser Enables or disables the  EcoFuser. Select On to 
reduce the power consumption to a minimum by 
turning off the heater of the fixing unit at  Sleep Mode. 
The default setting is  On.
Panel lock Locks or unlocks the operation panel. Locking the  operation panel disables key operations from the 
panel.
RAM disk Enables or disables  RAM disk mode. Enabling the 
RAM disk  allows you to use it as a temporary 
storage area for data such as font files or the 
contents of the receive buffer. You can also specify 
the RAM disk size by clicking  Enable.
Downloaded From ManualsPrinter.com Manuals 
						

							3-18Connecting and Printing
Uninstalling Software
The CD-ROM lets you remove the printer software.
1Click Remove Software . The Kyocera  Uninstall er appears.
2Select the software package to remove.
3Click Uninstall . 
The uninstaller starts.
4When Uninstall complete  screen appears, click Finish.
5Select whether you restart your computer or not, click  Finish.
NoteIn Windows Vista,  Remove Driver and Package  screen 
appears. Select Remove driver and driver package, and 
click  OK. 
Downloaded From ManualsPrinter.com Manuals 
						

							Maintenance4-1
4 Maintenance
This chapter explains how to replace the toner container and clean the 
printer
.
General Information 4-2
Toner Container Replacement 4-2
Cleaning the Printer 4-6
Prolonged Non-Use and Moving the Printer 4-9
Downloaded From ManualsPrinter.com Manuals 
						

							4-2Maintenance
General Information
This chapter describes basic maintenance tasks you can perform for the 
printer. You can replace the toner container according to the printers 
status:
Also, the internal parts need periodic cleaning.
Toner Container Replacement
The Toner indicator  identifies the toner status at two stages of toner 
usage. 
• When the printer becomes low on toner, the  Toner indicator flashes. 
Note the replacement is not always necessary at this stage. 
• If you ignore the above status and continue printing, the  To n e r 
indicator lights up just before the toner is used up. The  toner 
container  must then be replaced immediately.
In either case, replace the toner container. 
Frequency of toner container replacement
Assuming an average toner coverage of 5% and EcoPrint mode turned 
off, the  toner container  will need replacing approximately once every 
7,200 pages (FS-1300D) or 4,000 pages (FS-1100).
Starter Toner Container
The  toner container  packed with the new printer is a starter toner 
container. The  starter toner container  lasts an average of 3,600 pages 
(FS-1300D) or 2,000 pages (FS-1100).
To n e r  K i ts
For best results, we recommend that you only use genuine Kyocera 
Parts and Supplies.
A new toner kit contains the following items:
• Toner Container
• Plastic waste bag for old toner container
• Installation Guide
Note Information Collection on Memory Chips - The memory chip 
attached to the toner container is designed to improve 
convenience for the end user; to support the recycling operation of 
empty toner containers; and to gather information to support new 
product planning and development. The information gathered is 
anonymous - it cannot be associated to any specific individual and 
the data is intended to be used anonymously. 
Note Do not remove the toner container from the carton until you 
are ready to install it in the printer. 
Downloaded From ManualsPrinter.com Manuals 
						

							Maintenance4-3
Replacing the Toner Container
This section explains how to replace the toner container.
1Open the top cover.
2Turn lock lever  to the unlock position. Push lock lever  to the position 
marked arrow and pull out the toner container .
CAUTION  Do not attempt to incinerate the Toner 
Container. Dangerous sparks may cause burns.
IMPORTANT During toner container replacement, temporarily move 
storage media and computer supplies (such as floppy disks) away 
from the toner container. This is  to avoid damaging media by the 
magnetism of toner.
IMPORTANT Kyocera Mita Corporation is not liable against any 
damages or problems arising from the use of toner containers other than 
those designated as original Kyocer a toner containers. For optimum 
performance, it is also recommended to use only the Kyocera toner 
containers which are specifically intended for use in your country or 
region. If the toner container for another destinations is installed, the 
printer will stop printing.
NoteYou do not have to turn printer power off before starting 
the replacement. Any data that may be processing in the printer 
will be deleted if you turn the printer power off
. 
Note Put the old toner container in the plastic bag (supplied 
with the new toner kit) and discard it later according to the local 
code or regulations for waste disposal.
Downloaded From ManualsPrinter.com Manuals 
						

							4-4Maintenance
3Take the new toner container  out of the toner kit. Shake the new 
toner container  at least 5 times as shown in the figure in order to 
distribute the toner evenly inside the container.
4Remove the label from the  toner container.
5Install the new toner container  in the printer. Push firmly on the top of 
the container at the positions marked PUSH, until you hear a click.
Downloaded From ManualsPrinter.com Manuals 
						

							Maintenance4-5
6Turn lock lever  to the lock position.
7Close the top cover .
Downloaded From ManualsPrinter.com Manuals 
						

							4-6Maintenance
Cleaning the Printer
To avoid print quality problems, the interior of the printer must be 
cleaned with every toner container replacement.
1Open the top cover and front cover .
2Lift the process unit  together with the  toner container out of the 
printer.
3Remove the  drum unit from the printer by holding the  green levers 
with both hands.
Note The drum is sensitive to light. Never expose the  drum 
unit  to light for more than five minutes.
Downloaded From ManualsPrinter.com Manuals 
						

							Maintenance4-7
4Place the drum unit flat on a clean, level surface.
5Use a clean, lint free cloth to clean dust and dirt away from the metal 
registration roller .
6Slide the charger cleaner  (green) back and forth 2 or 3 times to clean 
the  charger wire , then return it to its original position (CLEANER 
HOME POSITION ).
7When cleaning is complete, return the drum unit  to the original 
position.
IMPORTANT Do not place the drum unit on end.
IMPORTANTTake care not to touch the  transfer roller (black) 
during cleaning.
IMPORTANT After cleaning, make sure you restore the charger 
cleaner to its home position.
Downloaded From ManualsPrinter.com Manuals 
						

							4-8Maintenance
8Return the process unit  to its position, aligning the guides at both 
ends with the slots in the printer. Then, close the  front cover and top 
cover .
Downloaded From ManualsPrinter.com Manuals