Kyocera FS 1128MFP User Manual

Default Setting (System Menu) 
OPERATION GUIDE8-123
8
4Press the OK key. The Address Book list screen 
appears.
5Press the U  or V key to select the destination you 
want to edit.
6Press [Menu] (the  Right Select key). Menu 
appears.
7Press the  U or  V key to select [Detail/Edit].
8Press the  OK key. This displays the screen for 
editing the selected destination.
The screen shown is the one when an individuals 
destination is selected.
9Edit items as necessary.
For how to edit ea ch item, refer to...

Default Setting (System Menu) 
8-124OPERATION GUIDE
Adding a Destination on One-touch Key
This machine has 11 one-touch keys and you can register 2 destinations to each of them.
The one-touch keys are arranged as shown below:
NOTE: Refer to One-Touch Key on page 3-7 for how to use them.
Registering new destination
Use the procedure below to register a  new destination under a One-touch key.
1In the basic screen, press the one-touch key to 
which you want to register the destination and hold 
it (2...

Default Setting (System Menu) 
OPERATION GUIDE8-125
8
Editing One-touch Key
Edit/delete the destinations you added to One-touch Key.
Use the procedure below to edit the one-touch key.
1In the basic screen, press the one-touch key where 
you want to edit the destination and hold it (2 
seconds or longer). Select Key Set. appears.
The screen shown is the one when No.1/No.12 is 
pressed and held.
2Press the U or  V key to select the key number 
where you want to edit the destination.
3Press the  OK key. The...

Default Setting (System Menu) 
8-126OPERATION GUIDE
7Press the OK key. A confirmation screen appears.
8Press [Yes] (the  Left Select key). The selected 
destination is registered to the one-touch key, 
overwriting the previous one.  Registered. is 
displayed and the screen returns to the basic 
screen.
Overwrite.
Are you sure?
z No. 1
[ Yes ] [ No ]
Downloaded From ManualsPrinter.com Manuals 

Default Setting (System Menu) 
OPERATION GUIDE8-127
8
Restarting the System
Restart the printer without turning the main power 
switch off. Use this to deal with any unstable operation 
by the machine. (Same as  the computer restart.) 
Use the procedure below to restart the system.
1In the Sys. Menu/Count. menu, press the  U or  V 
key to select [System], and press the  OK key.
When you are performing user management and 
have not logged in, a login screen will appear. 
Then, enter the user ID and...

Default Setting (System Menu) 
8-128OPERATION GUIDE
Network Setup
The following network settings are available.
• LAN Interface Setup …8-128
• TCP/IP (IPv4) Setup …8-129
• TCP/IP (IPv6)  Setup …8-129
• NetWare Setup …8-130
• AppleTalk Setup …8-132
• Protocol Detail …8-135
LAN Interface Setup
Specify the settings for the LAN interface to be used. The default setting is  Auto.
Use the procedure below to select the interface.
1In the Sys. Menu/Count. menu, press the  U or  V 
key to select [System], and...

Default Setting (System Menu) 
OPERATION GUIDE8-129
8
6Press the OK key. LAN Interface appears.
7Press the  U or  V key to select the desired LAN 
interface.
The available LAN interfaces are as follows:
Auto
10Base-Half
10Base-Full
100Base-Half
100Base-Full
8Press the  OK key.  Completed.  is displayed and the 
screen returns to the  Network Setting menu.
TCP/IP (IPv4) Setup
Set up TCP/IP to connect to the Windows network.
Refer to TCP/IP (IPv4) Setup (by Entering IP Addresses) on page 2-12  about the...

Default Setting (System Menu) 
8-130OPERATION GUIDE
2The System menu appears.
3Press the U or  V key to select [Network Setting].
4Press the  OK key. The Network Setting menu 
appears.
5Press the  U or  V key to select [TCP/IP Settings].
6Press the  OK key. The TCP/IP Settings menu 
appears.
7Press the  U or  V key to select [IPv6 Setting].
8Press the  OK key. IPv6 Setting appears. 
9Press the  U or  V key to select [On] or [Off]. 
10Press the  OK key.  Completed.  is displayed and the 
screen returns to...

Default Setting (System Menu) 
OPERATION GUIDE8-131
8
1In the Sys. Menu/Count. menu, press the U or  V 
key to select [System], and press the  OK key.
When you are performing user management and 
have not logged in, a login screen will appear. 
Then, enter the user ID and password to log in, and 
press [Login] (the  Right Select key).
2The System menu appears.
3Press the U or  V key to select [Network Setting].
4Press the  OK key. The Network Setting menu 
appears.
5Press the  U or  V key to select...

Default Setting (System Menu) 
8-132OPERATION GUIDE
Ether-II
802.2
SNAP
8Press the 
OK key.  Completed.  is displayed and the 
screen returns to the  Network Setting menu.
For detailed information on restarting the system, 
refer to  Restarting the System on page 8-127.
AppleTalk Setup
Select the Apple Talk network connection.
Refer to  AppleTalk Setup on page 2-22  about the procedures.
WSD Scan Setup
Select whether or not to use WS D Scan. The default setting is On.
Use the procedure below to setup the...