Kyocera FS 1028DP User Manual

KPDL Operators
7-139
keys to the CollateDetails parameter should have the following integer values depending 
on the mode of each  e-MPS function.
Examples :
To post a print job into the virtual mailbox aliased Robert, a typical CollateDetails 
sequence of parameters will be as follows:
 setpagedevice 
KPDL Error Messages 
Depending on the setting of the  doautocontinue parameter, the printing systems having 
the operator display display errors occurring during operation in the KPDL mode as fol-
lows....

Chapter 7 Emulation
7-140
KPDL Printable Area 
This printing system does not quite print to the edges of the paper. The edge limits of the 
printable area vary depending on the paper type as determined by the paper type KPDL 
operator. The edge limits are located as shown in the following figure and table. They 
adjust automatically to the size of the paper cassette (although not to the size of manually 
fed paper). 
12 ioerror Input/output error 
13 limitcheck Path too co mplex, more than 6 files open,...

KPDL Operators
7-141
Figure 7. 53.  Printable Area
Table 7.54.  Paper Sizes and Printable Area
Paper type Paper sizeEdge limits (A above) Printable area (B above) 
Horizontal Vertical
cm Points cm Pt. cm Pt. cm Pt. 
A3
a
a
For A3/ledger models. 29.7 x 42.0 842 x 1191 0.42 12 0.35 10 28.85 x 41.31 818 x 1171 
B4
a25.7 x 36.4 728 x 1032 0.42 12 0.35 10 24.83 x 35.70 704 x 1012 
A4 21.0 x 29.7 595 x 842 0.42 12 0.35 10 20.14 x 28.99 571 x 822 
A4 Small 21.0 x 29.7 595 x 842 0.875 25 0.875 25 19.22 x 27.94...

7-142
This page is left blank intentionally.
Downloaded From ManualsPrinter.com Manuals 

i
Index
Numerics
16-bit word,  4-13
A
Absolute coordinates ,  2-19
Absolute position,  2-2
Arc,  2-10
path mode drawing ,  2-24
B
Baseline ,  1-8
Beveled line join ,  2-21
Bézier curve,  2-26
Binary number,  2-13, 4-13
Bit image,  2-34
Bitmap font ,  4-6
Bitmap fonts ,  1-6, 4-6
block,  2-10
Box,  2-6
Butt cap ,  2-20
C
Cartesian (X,Y) coordinates ,  2-5
Case,  1-12
exception ,  1-13
Cassette size ,  1-4
Character cells ,  1-8
Character path,  2-33
Character set
KC-GL ,  
7-96
Character spacing ,  1-8...

ii
control codes,  7-24
emulation,  7-21
Even-odd rule (FILL) ,  2-32
F
Fill pattern ,  2-10
defining,  2-12
Filled area ,  1-9, 2-30
Filled block ,  2-10
Flag,  5-2
Flatness of curves ,  2-28
Font
characteristics ,  
4-9
definition,  4-2
identifying characteristics ,  4-1
selection,  4-7
Font mode,  4-10, 7-22
Font name,  4-6
Font number
assigning to a scalable font (SFNT) ,  
4-8
Font orientation,  4-9
Font selection,  4-7, 7-35
by embedded software commands ,  4-12
by PRESCRIBE,  4-7
font selection...

iii
O
Origin,  1-7
P
Page direction ,  1-5
Page orientation ,  1-5
Path mode graphics ,  2-16
Pattern number,  2-22, 2-24
Permanent parameters ,  6-1
Physical page,  1-9
Pie charts,  2-14
Plotter units ,  7-100
PRESCRIBE
command length limit ,  
1-4
format,  1-4
Presentation mode ,  2-36
Print direction,  1-6
Print model,  2-1
Proportional fonts ,  1-8
Proportional spacing ,  1-8
Q
Quotation marks ,  1-11
R
Radius ,  2-9, 2-15
Raster data
in taggged image file format ,  
2-34
printing commands,  2-35...

     
Downloaded From ManualsPrinter.com Manuals 

Downloaded From ManualsPrinter.com Manuals 

Rev. 4.7 2009.7
Downloaded From ManualsPrinter.com Manuals