Konica Minolta PagePro 4650EN User Manual

Antistatic Protection 191
Antistatic Protection
Note
It’s very important to protect the printer controller board from 
electrostatic damage while performing any task involving the controller 
board.
Turn off all power switches first. If an antistatic wrist strap is provided in 
your printer option kit, attach one end of it to your wrist and the other 
end to the bare metal chassis on the back of your printer. Never attach 
the wrist strap to any piece of equipment with an electrical current 
present....

Dual In-Line Memory Module (DIMM) 192
Dual In-Line Memory Module (DIMM)
You may need additional memory (DIMM) for complex graphics and 
for duplex (double-sided) printing. 
This printer detects only half of the amount of the installed memory.
Dual in-line memory module (or DIMM) is compact circuit board with sur-
face-mount memory chips.
There is 256 MB of onboard memory and one available memory expansion 
slot. The memory can be expanded to a maximum of 384 MB (128 MB + 256 
MB).
Installing a DIMM...

Dual In-Line Memory Module (DIMM) 193
2Using a screwdriver, loosen the 
screw of the right cover, located 
at the rear side.
3Remove the right side cover.
4Using a screwdriver, loosen the 
two screws. (Do not remove 
them from the printer.)
Downloaded From ManualsPrinter.com Manuals 

Dual In-Line Memory Module (DIMM) 194
5Remove the panel.
6Insert the DIMM at an angle 
(about 45°) into the connector, 
making sure that the notch on 
the unit aligns with the tab on 
connector, and then press down 
carefully until it clicks into place.
Be sure to handle the 
DIMM by the edges only.
You will hear a click when 
the DIMM is properly 
placed.
7Reinstall the panel and tighten 
the two screws.
8Attach the right side cover.
9Reconnect all interface cables.
10Reconnect the power cord, and...

Dual In-Line Memory Module (DIMM) 195
11Declare the additional Printer Memory in the Windows printer driver 
(Properties/Configure tab).
12Print a configuration page (PRINT MENU/CONFIGURATION PG) and 
verify that the total amount of the RAM installed in your printer is listed.
Downloaded From ManualsPrinter.com Manuals 

Hard Disk Kit 196
Hard Disk Kit
If you install a hard disk kit, the followings can be performed:
–Collate printing
–Job printing/saving
–Fonts/forms download
–User Authentication/Account Track
–Direct printing
A hard disk kit and a CF adapter cannot be installed simultaneously.
Installing the Hard Disk kit
Note
It’s very important to protect the printer controller board and any 
associated circuit boards from electrostatic damage. Before performing 
this procedure, review the antistatic caution on page...

Hard Disk Kit 197
2Using a screwdriver, loosen the 
screw of the right cover, located 
at the rear side.
3Remove the right side cover.
4Using a screwdriver, loosen the 
two screws. (Do not remove 
them from the printer.)
Downloaded From ManualsPrinter.com Manuals 

Hard Disk Kit 198
5Remove the panel.
6Plug the cable on the hard disk 
kit into the connector on the con-
troller board.
7Mount the hard disk kit onto the 
controller board as shown in the 
figure, and then tighten the two 
screws.
8Reinstall the panel and tighten the two screws.
9Attach the right side cover.
Downloaded From ManualsPrinter.com Manuals 

Hard Disk Kit 199
10Reconnect all interface cables.
11Reconnect the power cord, and 
turn on the printer.
12Declare the Hard Disk in the Windows printer driver (Properties/Configure 
tab).
Downloaded From ManualsPrinter.com Manuals 

CompactFlash 200
CompactFlash
If you install a CF Adapter and CompactFlash card, the followings can be per-
formed:
–Collate printing
–Fonts/forms download
–Authentication/Account Track
–Direct printing (including the use of PageScope Direct Print)
Only CompactFlash cards with a capacity of 256 MB, 512 MB, 1 GB, 2 
GB or 4 GB can be used.
The job printing/saving function is not available with a CompactFlash 
card. This function requires that an optional hard disk kit be installed.
A hard disk kit and...