Konica Minolta PagePro 4650EN User Manual

Finishing 111 Offset Printing
If offset printing is selected, the paper is fed out shifted as shown below.
When PAPER MENU/COLLATE is set to ON, the pages are fed out 
in sets as shown below.
- When 
COLLATE is set to ON- When COLLATE is set to OFF
321321
321
333222
111
Downloaded From ManualsPrinter.com Manuals 

Media Storage 112
Media Storage
How do I store media?
„Keep media on a flat, level surface in its original wrapper until it is time to
load it.
Media that has been stored for a long time out of its packaging may dry up 
too much and cause misfeeding.
„If media has been removed from its wrapper, place it in its original pack-
aging and store in a cool, dark place on a level surface.
„Avoid moisture, excessive humidity, direct sunlight, excessive heat (above 
35°C [95°F]), and dust.
„Avoid leaning media...

Replacing
Consumables
Downloaded From ManualsPrinter.com Manuals 

Replacing Consumables 114
Replacing Consumables
Before replacing consumables, make sure that the power of the printer is 
turned off.
Note
Failure to follow instructions as outlined in this manual could result in 
voiding your warranty.
Note
If an error message (TONER OUT, FUSER UNIT END OF LIFE, etc.) 
appears, print out the configuration page, and then check the status of the 
consumables. For details on the error messages, refer to “Error Messages 
(Warning:)” on page 182. For details on printing the...

Replacing Consumables 115
Refer to the following URL for recycling information. 
US: printer.konicaminolta.net/products/recycle/index.asp 
Europe: www.konicaminolta.eu/printing-solutions/more-information/
clean-planet.html
Other regions: printer.konicaminolta.com
Note
Do not use refilled toner cartridges or unapproved toner cartridges. Any 
damage to the printer or quality problems caused by a refilled toner 
cartridge or an unapproved toner cartridge will void your warranty. No 
technical support is...

Replacing Consumables 116
The maximum storage temperature is 35°C (95°F) and the maximum 
storage humidity is 85% (noncondensing). If the toner cartridge is moved 
from a cold place to a warm, humid place, condensation may occur, 
degrading print quality. Allow the toner to adapt to the environment for 
about one hour before use.
„Level during handling and storage. 
Do not hold, stand or store a cartridge on its ends or turn it upside down; 
the toner inside the cartridge may become caked or unequally...

Replacing Consumables 117 Replacing a Toner Cartridge
Note
Be careful not to spill toner while replacing a toner cartridge. If toner 
spills, immediately wipe it off with a soft, dry cloth.
If 
TONER LOW on the SYS DEFAULT MENU/ENABLE WARNING is set 
to 
ON, the message TONER LOW appears when the toner cartridge becomes 
near empty. Follow the steps below to replace the toner cartridge.
If TONER LOW on the SYS DEFAULT MENU/ENABLE WARNING 
is set to 
OFF, you are advised to replace the toner cartridge...

Replacing Consumables 118
4Holding it firmly with both hands, 
rock the toner cartridge left and 
right, forward and backward, to 
distribute the toner evenly.
Do not touch the devel-
oping roller of the toner 
cartridge; otherwise 
image quality may 
decrease.
5Placing the toner cartridge on a 
flat surface, pull out the seal hor-
izontally.
6Hold the toner cartridge by the 
grip, and then insert it into the 
slot inside the printer.
Downloaded From ManualsPrinter.com Manuals 

Replacing Consumables 119
7Close the top cover securely.
Note
Dispose of the used toner cartridge according to your local regulations. 
Do not burn the toner cartridge.
For details, refer to “About toner cartridge” on page 114.
Replacing the Fuser Unit
When it is time to replace the fuser unit, the message FUSER UNIT END 
OF LIFE
 appears. Printing can continue even after this message appears; 
however, since the print quality is reduced, the fuser unit should be replaced 
immediately.
Downloaded From...

Replacing Consumables 120
1Turn off the printer and discon-
nect the power cord.
There are extremely hot 
parts within the machine. 
Before replacing the 
fuser unit, wait about 30 
minutes after turning off 
the machine, and then 
check that the fusing sec-
tion has reached room 
temperature; otherwise, 
you may get burnt.
2Lift the lever shown in the figure.
3Open the rear cover.
Do not touch any parts 
inside the printer.
Downloaded From ManualsPrinter.com Manuals