Konica Minolta magicolor 4650DN User Manual

Cleaning the Printer 167
Cleaning the Media Feed Rollers (Tray 2/3)
1Pull out the tray.
2Clean the media feed rollers by 
wiping them with a soft, dry 
cloth.
3Close the tray.
Downloaded From ManualsPrinter.com Manuals 

Cleaning the Printer 168
Cleaning the Media Transfer Rollers for Tray 3
1Open the right side cover of 
Tray 3.
Before opening the right 
side cover of Tray 3 , fold 
up Tray 1.
2Clean the media transfer rollers 
by wiping them with a soft, dry 
cloth.
3Close the right side cover of 
Tray 3.
Downloaded From ManualsPrinter.com Manuals 

Cleaning the Printer 169 Cleaning the Laser Lens
This printer is constructed with four laser lenses. Clean all lenses as 
described below. The laser lens cleaning tool should be attached to the inside 
of the front cover.
1Open the printer’s front cover 
and remove the cleaning tool 
from the machine’s front cover.
 
2Insert the laser lens cleaning 
tool into the laser lens cleaning 
opening, pull it out, and then 
repeat this back and forth move-
ment 2 or 3 times.
3Clean between each of the laser...

Cleaning the Printer 170
4Return the laser lens cleaning tool to its holder on the inside of the front 
cover.
5Close the front cover.
Downloaded From ManualsPrinter.com Manuals 

10
Troubleshooting
Downloaded From ManualsPrinter.com Manuals 

Introduction 172
Introduction
This chapter provides information to aid you in resolving printer problems you 
may encounter, or at least guide you to the proper sources for help. 
Printing a Configuration Page
Print a configuration page to verify the printer is printing correctly, or to check 
the printer configuration.Printing the configuration page Page 172
Preventing media misfeeds Page 173
Understanding the media path Page 174
Clearing media misfeeds Page 175
Solving problems with media misfeeds Page...

Preventing Media Misfeeds 173
Preventing Media Misfeeds
Make sure that...
Media matches the printer specifications.
Media is flat, especially on the leading edge.
The printer is on a hard, flat, level surface.
You store media in a dry location away from moisture and humidity.
You remove transparencies from the output tray immediately after printing to 
avoid static buildup.
You always adjust the media guides in the tray after inserting the media (a 
guide that is not properly adjusted can cause poor...

Understanding the Media Path 174
Understanding the Media Path
Understanding the printer’s media path will help you locate media misfeeds
1 Toner cartridge 6 Tray 3 (optional lower feeder 
unit)
2 Output tray 7 Tray 2
3 Fuser unit 8 Laser
4 Duplex (magicolor 4650DN only) 9 Imaging unit
5 Tray 1 (Manual feed tray) 10 Transfer belt unit
321
9 10
5
4
8
7
6
Downloaded From ManualsPrinter.com Manuals 

Clearing Media Misfeeds 175
Clearing Media Misfeeds 
To avoid damage, always remove misfed media gently, without tearing it. Any 
piece of media left in the printer, whether large or small, can obstruct the 
media path and cause further misfeeds. Do not reload media that has misfed.
Note
The image is not fixed on the media before the fusing process. If you 
touch the printed surface, the toner may stick to your hands, so be 
careful not to touch the printed face when removing the misfed media. 
Make sure...

Clearing Media Misfeeds 176
Media Misfeed Messages and Clearing Procedures
If the message PAPER JAM/VERTICAL TRANS appears, check 
for media misfeeds in the transfer roller section of the right side covers 
for Tray 3. Media Misfeed Message Page Reference
PAPER JAM
TRAY 2Page 177
PAPER JAM
TRAY 3Page 181
PAPER JAM 
DUPLEX 1Page 183
PAPER JAM
DUPLEX 2Page 183
PAPER JAM
FUSER/EXITPage 184
PAPER JAM
TRAY 1Page 188
PAPER JAM
SECOND TRANSPage 188
PAPER JAM
VERTICAL TRANSPage 181, Page 188
Downloaded From...