Konica Minolta magicolor 1600W User Manual

							Replacing Consumables 5-4
Keep toner cartridges: 
„In their packaging until you’re ready to install them.
„In a cool, dry location away from sunlight (due to heat). 
The maximum storage temperature is 35° C (95° F) and the maximum 
storage humidity is 85% (noncondensing). If the toner cartridge is moved 
from a cold place to a warm, humid place, condensation may occur, 
degrading print quality. Allow the toner to adapt to the environment for 
about one hour before use.
„Level during handling and storage. 
Do not hold, stand or store 
cartridges on their ends or turn 
them upside down; the toner 
inside the cartridges may 
become caked or unequally 
distributed.
„Away from salty air and corrosive gases such as aerosols.
Downloaded From ManualsPrinter.com Manuals 
						

							Replacing Consumables5-5
Replacing a Toner Cartridge
Note
Be careful not to spill toner while replacing a toner cartridge. If toner 
spills, immediately wipe it off with a soft, dry cloth.
When the toner is empty, the toner indicator lights up. Follow the procedure 
described below to replace the toner cartridge.
1Check the control panel to see which color of toner is empty. 
As an example, the procedure for replacing the magenta toner cartridge is 
described below.
If the toner becomes empty, the toner indicator lights up and the 
empty toner cartridge is automatically moved so that it can be 
replaced.
 
If this has occurred, skip step 2 and continue with step 3.
2Use either operation described below to switch the printer to Change 
Toner mode.
zPress the Rotate Toner key.
zOn the Panel tab of the Remote Panel Utility, select Change Toner, 
and then click the Rotate Toner button.
The printer enters Change Toner mode, and the magenta toner 
indicator lights up.
With each additional press of the Rotate Toner key, the cyan, 
black, then yellow toner cartridge moves so that they can be 
replaced. The indicator for the toner cartridge that was moved 
so that it can be replaced lights up.
To exit Change Toner mode, press the Clear key.
Downloaded From ManualsPrinter.com Manuals 
						

							Replacing Consumables 5-6
3Open the front cover.
Before opening the front 
cover, open Tray 1 if it is 
not already open.
4Check that the toner cartridge to be replaced has been moved to the front.
You can identify the toner cartridge by the color of the handle.
5Pull down the handle on the 
toner cartridge until the toner 
cartridge is unlocked and moves 
out slightly toward you.
 
Remove the toner cartridge.
Do not manually rotate 
the toner cartridge carou
-
sel. In addition, do not 
rotate the carousel with 
force, otherwise it may be 
damaged.
Downloaded From ManualsPrinter.com Manuals 
						

							Replacing Consumables5-7
Note
Do not touch the contact 
indicated in the illustration.
 
 
 
 
 
 
 
 
 
 
 
 
Note
Dispose of the empty toner cartridge according to your local 
regulations. Do not burn the toner cartridge.
 
For details, refer to “About Toner Cartridges” on page 5-2.
6Prepare a new toner cartridge.
7Shake the cartridge a few times 
to distribute the toner.
Make sure that the toner 
roller cover is securely 
attached before shaking 
the toner cartridge.
Downloaded From ManualsPrinter.com Manuals 
						

							Replacing Consumables 5-8
8Remove the cover from the 
toner roller.
Do not touch or scratch 
the toner roller.
9Align the shaft on each end of 
the toner cartridge with its hold
-
ers, and then insert the car-
tridge.
Before inserting the toner 
cartridge, make sure that 
the color of the toner car
-
tridge to be installed is 
the same as the label on 
the toner cartridge carou
-
sel.
Downloaded From ManualsPrinter.com Manuals 
						

							Replacing Consumables5-9
Note
Do not touch the contact 
indicated in the illustration.
 
 
 
 
 
 
 
 
 
 
 
 
10Press in the toner cartridge until 
it locks into place.
11Close the front cover.
To replace the toner car-
tridge for another color, 
after the front cover has 
been closed, check that 
the indicator for the toner 
to be replaced is lit (if 
necessary, press the 
Rotate Toner key), and 
then replace the toner 
cartridge as described in 
steps 3 through 11.
12Press the Clear key to reset the 
printer and clear the indicator message.
Downloaded From ManualsPrinter.com Manuals 
						

							Replacing Consumables 5-10
The printer must complete a calibration cycle (less than 2 minutes) 
after a toner cartridge has been replaced. If you open the top or 
front cover before the printer is reset, the calibration stops, then 
starts over again after the cover is closed.
Downloaded From ManualsPrinter.com Manuals 
						

							Replacing Consumables5-11
Replacing All Toner Cartridges at the Same Time
Note
Be careful not to spill toner while replacing a toner cartridge. If toner 
spills, immediately wipe it off with a soft, dry cloth.
By using the Eject All Toner mode, all toner cartridges can be replaced at the 
same time.
Follow the procedure described below to use the Eject All Toner mode.
1Use either operation described below to switch the printer to Eject All 
Toner mode.
zHold down the Rotate Toner key for more than 10 seconds.
zOn the Panel tab of the Remote Panel Utility, select Eject All Toner, 
and then click the Rotate Toner button.
The printer enters Eject All Toner mode, and the magenta toner 
indicator lights up.
To exit Eject All Toner mode, press the Clear key.
2Perform the operations described in steps 3 through 11 of “Replacing a 
Toner Cartridge” on page 5-6 through 5-9 to replace the magenta toner 
cartridge.
3Follow the same procedure to replace the cartridges for the cyan, black, 
then yellow toners.
4Press the Clear key to reset the printer and clear the indicator message.
The printer must complete a calibration cycle (less than 2 minutes) 
after a toner cartridge has been replaced. If you open the top or 
front cover before the printer is reset, the calibration stops, then 
starts over again after the cover is closed.
Downloaded From ManualsPrinter.com Manuals 
						

							Replacing Consumables 5-12
Replacing the Imaging Cartridge
When replacing an imaging cartridge, refer to the following table. For opti-
mum print quality and performance, use only approved KONICA MINOLTA 
imaging cartridge for your specific printer type, as listed in the table below. 
You can find your machine type and the imaging cartridge part numbers on 
the consumables reorder label  inside the top cover your machine.
For optimum print quality and performance, use only the corre-
sponded TYPE genuine KONICA MINOLTA imaging cartridge.
1Open the top cover.
If there is paper in the 
output tray, remove it, 
and then fold up the out
-
put tray before opening 
the top cover.
2Grab the handle and lift it up 
slightly to the back, and then 
slowly pull the imaging cartridge 
out vertically.
Printer 
Ty p ePrinter Part 
NumberPart NameImaging Cartridge 
Part Number
AMA034 011Imaging CartridgeA0VU 011
EUA034 021A0VU 0Y1
APA034 041A0VU 0Y1
GCA034 081A0VU 0Y1
Downloaded From ManualsPrinter.com Manuals 
						

							Replacing Consumables5-13
Note
Dispose of the used imaging cartridge according to your local 
regulations. Do not burn the imaging cartridge.
3Prepare the new imaging cartridge.
Note
Do not touch the PC drum and the transfer belt on the imaging 
cartridge.
 
 
 
 
 
 
 
 
 
 
 
4Slowly insert the new imaging 
cartridge vertically, and then 
push it slightly down toward you 
to finish installing the imaging 
cartridge.
Downloaded From ManualsPrinter.com Manuals