Konica Minolta bizhub C452 User Manual

							bizhub C652/C652DS/C552/C552DS/C4527-13
7.1 System Settings7
Leading Edge Adjustment
Adjust the starting print position at the leading edge of each type of paper (with respect to the paper feed 
direction).
1Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment] 
ö [Printer Adjustment] ö [Leading Edge Adjustment].
%To adjust the starting print position at the leading edge of the second side for 2-sided printing (with 
respect to the paper feed direction), press [Leading Edge Adjustment (Duplex Side 2)].
2Select a paper type to be adjusted.
3Load the paper into the bypass tray.
4Press the [Start] key.
A test pattern is printed.
5Check that the distance from the starting print position of the test 
pattern to the edge of the paper (a) is 4.2 mm. 
%Press [+] or [-] to adjust the width. 
Press the [Start] key to print a test pattern.
6Press [OK].
Centering
Adjust the starting print position at the left edge of each paper tray (with respect to the paper feed direction).
0Only 8-1/2 e 11 v (A4 v) paper can be used to adjust the bypass tray.
1Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment] 
ö [Printer Adjustment] ö [Centering].
%To adjust the starting print position at the left edge of the second side for 2-sided printing (with 
respect to the paper feed direction), press [Centering (Duplex 2nd Side)].
2Select a paper tray to be adjusted.
3Press the [Start] kay.
A test pattern is printed. Color Registration Adjust 0 dot
Prior Detection Setting Yes
Warning Display: TYPE1
Detection Level: Std.
Prior Detection Setting 
(front)Yes
Warning Display: TYPE1
Detection Level: Std.
Prior Detection Setting 
(back)
Feed Cleaning Settings Remove
Non-Image Area Erase Op-
eration SettingsErase Operation: Specify
Erase Method: Rectangular
Original Density: 3 Factory default
a
a:4.2mm
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C4527-14
7.1 System Settings7
4Check that the distance from the starting print position of the test 
pattern to the left edge of the paper (b) is 3.0 mm (+/-0.5 mm).
%Press [+] or [-] to adjust the width. 
Press the [Start] key to print a test pattern.
5Press [OK].
Media Adjustment
Adjust defective print images caused by paper type features.
1Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment] 
ö [Printer Adjustment] ö [Media Adjustment].
2Select a paper type to be adjusted.
%If defective images exist on the back side of 2-sided copy paper, select [2nd Side].
3Press [+] or [-] to specify an adjusted value.
%If missing parts or white spots exist in print images, press [-]. If the surface of the print image is 
rough, press [+].
4Press [OK] ö [Close].
5Copy, and then check the print image.
Center Staple Position
Adjust the stapling position for each paper size when printing with the center staple function.
0Adjust the half-fold position before adjusting the center stapling position.
0Before making any adjustments, create a sample using the center staple function. Adjust the center 
staple position while checking the created sample.
0It can be adjusted only when the saddle sticher is installed.
0When stapling in parallel with the left edge of paper, contact your service representative.
1Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment] 
ö [Finisher Adjustment] ö [Center Staple Position].
2Select the size of paper of which the center staple position is adjusted.
3Press [+] or [-] to adjust the staple position while checking the sample.
4Press [OK].
5Create a sample, and check the print result.
b
b:3.0mm±0.5mm
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C4527-15
7.1 System Settings7
dReference
To adjust the half-fold position:
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment] ö 
[Finisher Adjustment] ö [Half-Fold Position].
Half-Fold Position
Adjust the center staple & fold and half-fold positions.
0Before making any adjustments, create a sample using the half-fold function. Adjust the half-fold 
position while checking the created sample.
0It can be adjusted only when the saddle sticher is installed.
0When adjusting the half-fold position in parallel with the left edge of paper, contact your service 
representative.
1Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment] 
ö [Finisher Adjustment] ö [Half-Fold Position].
2Select the size of paper of which half-fold position is adjusted.
3Press [+] or [-] to adjust the punched hole position while checking the sample.
4Press [OK].
5Create a sample, and check the print result.
Tri-Fold Position Adjustment
Adjust the folding position for each paper size when printing with the tri-fold function. The folding width 
depends on the paper size, which cannot be changed.
0Before making any adjustments, create a sample using the tri-fold function. Adjust the tri-fold position 
while checking the created sample.
0It can be adjusted when the Finisher FS-526 and Saddle Stitcher SD-508 are installed.
1Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment] 
ö [Finisher Adjustment] ö [Tri-Fold Position Adjustment].
2Select the size of paper of which tri-fold position is adjusted.
3Press [+] or [-] to adjust the tri-fold position while checking the sample.
4Press [OK].
5Create a sample, and check the print result.
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C4527-16
7.1 System Settings7
Punch Vertical Position Adjustment
Adjust the vertical position of the punched holes for each paper size.
0Before making any adjustments, create a sample using the punch settings. Adjust the punched hole 
position while checking the created sample.
0This adjustment is available if the Finisher FS-526 and Punch Kit PK-516 are installed.
1Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment] 
ö [Finisher Adjustment] ö [Punch Vertical Position Adjustment]. 
2Select the paper size to adjust the vertical punch position.
3Press [+] or [-] to adjust the punched hole position while checking the sample.
4Press [OK].
5Create a sample, and check the print result.
Punch Horizontal Position Adjustment
Adjust the horizontal position of the punched holes. Adjust the horizontal position of the punched holes as 
appropriate for each installed option or paper type.
0Before making any adjustments, create a sample using the punch settings. Adjust the punched hole 
position while checking the created sample.
0The horizontal position of the punched holes can be adjusted as appropriate for each installed option 
if the finisher FS-526, punch kit PK-516, and post inserter are installed.
0This adjustment is available for each paper type if the Finisher FS-527 and Punch Kit PK-517 are 
installed.
1Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment] 
ö [Finisher Adjustment] ö [Punch Horizontal Position Adjustment].
%Select an option to adjust the horizontal position of the punched holes if the post inserter is installed.
%First, select the paper type if the finisher FS-527 and punch kit PK-517 are installed.
2Press [+] or [-] to adjust the punched hole position while checking the sample.
3Press [OK].
4Create a sample, and check the print result.
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C4527-17
7.1 System Settings7
Punch Regist Loop Size Adjustment
Correct the orientation of the paper and adjust the punched hole position to be parallel with the left edge of 
the paper. The punched hole array is corrected by adjusting the resistance applied to the paper for each 
paper type.
0This adjustment is available if the punch kit is installed.
1Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment] 
ö [Finisher Adjustment] ö [Punch Regist Loop Size Adjustment].
First select the option to adjust the inclination of punch holes when the Finisher FS-526 and Post 
Inserter PI-505 or Z Folding Unit ZU-606 are installed.
2Select a paper type for which the punch hole angle is adjusted.
3Press [+] or [-] to adjust the punched hole position.
4Press [OK].
5Create a sample, and check the print result.
Punch Edge Sensor Adjustment
If the punch position is displaced depending on the paper tray, the punch kit is automatically adjusted.
0This adjustment is available if the Finisher FS-526 and the Punch Kit PK-516 are installed.
1Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment] 
ö [Finisher Adjustment] ö [Punch Edge Sensor Adjustment].
2Press the [Start] key.
The punch edge sensor is automatically adjusted.
The adjusted result appears.
Vertical Punch (Z-Fold) Position Adjustment
Adjust the vertical position of the punched holes for each paper size.
0Before making any adjustments, create a sample using the punch settings. Adjust the center staple 
position while checking the created sample.
0This adjustment is available if the Z Folding Unit is installed.
1Select [Utility/Counter] ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment] ö 
[Finisher Adjustment] ö [Vertical Punch (Z-Fold) Position Adjustment].
2Select the size of paper of which the vertical punched hole position is adjusted.
3Press [+] or [-] to adjust the punched hole position while checking the sample.
4Press [OK].
5Create a sample, and check the print result.
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C4527-18
7.1 System Settings7
Horizontal Punch (Z-Fold) Position Adjustment
Adjust the horizontal position of the punched holes for each paper size.
0Before making any adjustments, create a sample using the punch settings. Adjust the center staple 
position while checking the created sample.
0This adjustment is available if the Z Folding Unit is installed.
1Select [Utility/Counter] ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment] ö 
[Finisher Adjustment] ö [Horizontal Punch (Z-Fold) Position Adjustment].
2Press [+] or [-] to adjust the punched hole position while checking the sample.
3Press [OK].
4Create a sample, and check the print result.
1st Z-Fold Position Adjustment
Adjust the first paper folding position for each paper size when using the Z-fold function. 
0Before making any adjustments, create a sample using the Z-fold function. Adjust the center staple 
position while checking the created sample.
0This adjustment is available if the Z Folding Unit is installed.
1Select [Utility/Counter] ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment] ö 
[Finisher Adjustment] ö [1st Z-Fold Position Adjustment].
2While checking the sample, press [+] or [-] to adjust the first folding position.
3Press [OK].
4Create a sample, and check the print result.
1st Z-Fold Position
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C4527-19
7.1 System Settings7
2nd Z-Fold Position Adjustment
Adjust the second paper folding position for each paper size when using the Z-fold function. 
0Before making any adjustments, create a sample using the Z-fold function. Adjust the center staple 
position while checking the created sample.
0This adjustment is available if the Z Folding Unit is installed.
1Select [Utility/Counter] ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment] ö 
[Finisher Adjustment] ö [2nd Z-Fold Position Adjustment].
2While checking the sample, press [+] or [-] to adjust the second folding position.
%The distance between the left end of paper and the second Z-fold position must be 2 mm or more.
3Press [OK].
4Create a sample, and check the print result.
Punch Unit Size Detect Sensor
If the punch position is displaced depending on the paper tray, the punch unit is automatically adjusted.
0This adjustment is available if the Z Folding Unit or Punch Kit PK-516 is installed.
1Select [Utility/Counter] ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment] ö 
[Finisher Adjustment] ö [Punch Unit Size Detect Sensor].
2Press [Start].
%The punch unit edge sensor is automatically adjusted.
%The adjusted result appears.
2nd Z-Fold Position
2 mm or more
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C4527-20
7.1 System Settings7
Color Registration Adjust
If color shifts are detected in the print result, adjust the each color print position for each paper type.
0The procedure for adjusting the color registration is the same for yellow, magenta and cyan.
1Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment] 
ö [Color Registration Adjust].
2Select a color to be corrected.
3Select a paper type for which color registration is adjusted.
4Load the paper into the bypass tray.
%The loadable paper size is 11 e 17w, 8-1/2 e 11v, A3 w, or A4 v.
5Press the [Start] key.
A test pattern is printed.
6Check that the black line aligns with the color line to be adjusted 
at the X and Y positions of the test pattern.
%Press [+] or [-] to adjust the color line to be corrected while checking the sample.
The color registration is adjusted.
7Press the [Start] key to print a test pattern, and then check the print result.
8Press [OK].
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C4527-21
7.1 System Settings7
Gradation Adjustment
Adjust irregular gradation levels of print images.
0Adjust each correction item three times.
1Turn off the main power switch of this machine.
2Wait at least 10 seconds, and then turn it on again.
3Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment] 
ö [Gradation Adjustment].
4Press the [Start] key.
The image stabilization operation starts.
The correction items on the right of the touch panel become enabled.
5Select an item to be corrected.
6Select paper used to output a test pattern.
%As a paper size, select 11 e 17w, 8-1/2 e 11v, A3w or A4 v. By default, 11 e 17 w (A3 w) is 
selected.
%Paper in the bypass tray cannot be selected.
7Press the [Start] key.
A test pattern is printed.
%Selecting 11 e 17w or A3w outputs one sheets, and selecting 8-1/2 e 11v or A4v outputs two 
sheets.
8Place the printed test pattern on the original glass in orientation displayed in the touch panel.
%For the test patterns of 8-1/2 e 11v or A4v, place the output two sheets side by side.
9Place 10 or more sheets of blank paper on top of the test pattern to prevent it from becoming 
transparent.
10Close the ADF.
11Press the [Start] key.
The test pattern is scanned.
The gradation level is automatically adjusted.
12Repeat steps 5 through 11 two more times.
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C4527-22
7.1 System Settings7
7.1.8 List/Counter
Configure the job settings list print settings and paper count settings for this machine. 
%Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [List/Counter].
Settings
Management List Job Settings List Configure paper tray settings for printing the job 
settings list and specify a print side.
Paper Size/Type Counter Register a combination of paper size and paper type for a counter. Every 
time the counter is changed, the count is reset to 0.
Counter Clear Resets the count to 0.
Paper Size Select the paper size of the counter.
Paper Type Select the paper type of the counter.
Factory default
Job Settings List • 1-Sided
• Tray 1
Downloaded From ManualsPrinter.com Manuals