Kodak Dp2900 Projector User Manual

Using the Projector
41
Status Menu
This is a read-only window for informational purposes. To display the 
status window, select Show status from the menu, then click the left 
or right navigation button. To remove the window, click the left or 
right navigation button. 
Lamp hours used
Indicates how many hours the current lamp has been in use. The 
counter starts at zero hours and counts each hour the lamp is in use. 
Change the bulb when the brightness is no longer acceptable. See 
“Replacing the...

User Guide KODAK DP2900 Digital Projector 
42
Source
Indicates the active source, Computer analog, Computer digital, or 
Video.
Software version
Indicates the projector’s software version. This information is useful 
when contacting Technical Support.
Startup screen version
Indicates the projector’s splash screen version. This information is 
useful when contacting Technical Support.
Boot version
Indicates the projector’s boot software version. This information is 
useful when contacting Technical Support. 

Using the Projector
43
Using KODAK Image Manager
With one click, Kodak’s exclusive Image Manager lets you choose the best 
image settings for your presentation type.
Important:The KODAK Image Manager settings work best if you select Reset 
from the Adjust tab each time before selecting an Image Manager 
setting.
Move the cursor to the option you want, then click the left or right navigation 
button.
Photos (PC) matches the higher contrast found on a standard PC monitor. 
This feature is best for:
•...

45
Maintenance &
Troubleshooting
This section describes how to:
• clean the lens
• replace the projection lamp 
• replace the batteries in the remote
• use the security lock feature
• troubleshoot the projector
Cleaning the Lens
Follow these steps to clean the projection lens:
 1. Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
• Avoid using an excessive amount of cleaner.
• Abrasive cleaners, solvents or other harsh chemicals might 
scratch the lens.
 2. Lightly wipe the cleaning cloth...

User Guide KODAK DP2900 Digital Projector 
46
Replacing the Projection Lamp
Warning: To avoid burns, allow the projector to cool for at least 30 
minutes before you open the lamp module door. Never 
extract the lamp module while the lamp is operating.
,PSRUWDQW 7KHODPSLQWKH.2$.3FRQWDLQVWUDFHDPRXQWVRIPHUFXU\
6RPHJRYHUQPHQWVUHTXLUHVSHFLDOGLVSRVDORIODPSVFRQWDLQLQJPHUFXU\
LVSRVHRIODPSVLQDFFRUGDQFHZLWKWKHODZDQGDQ\DSSOLFDEOHORFDO
UHJXODWLRQV
The lamp hour counter in the...

Maintenance & Troubleshooting
47
 4. Pull the lamp door up and remove it.
Warning:Be extremely careful when removing the lamp module. In 
the unlikely event that the bulb ruptures, small glass 
fragments may be generated. The lamp module is 
designed to contain these fragments, but use caution 
when removing the lamp module
&DXWLRQ 1HYHURSHUDWHWKHSURMHFWRUZLWKWKHODPSGRRURSHQRU
UHPRYHG7KLVGLVUXSWVWKHDLUIORZDQGFDXVHVWKH
SURMHFWRUWRRYHUKHDW
 5. Loosen the two non-removable screws on...

User Guide KODAK DP2900 Digital Projector 
48
 6. Lift and grasp the pull tab and lift the module out. Dispose of the 
lamp module in an environmentally proper manner.
Warning: Do not drop the lamp module or touch the glass bulb! 
The glass may shatter and cause injury.
 7. Install the new lamp module, being sure to align the connectors 
properly.
 8. Push the module in until it is flush with the bottom case of the 
projector.
 9. Tighten the screws on the outside of the module. 
...

Maintenance & Troubleshooting
49
Replacing the Batteries in the Remote 
Control
The life of the batteries depends on how often and how long you use 
the remote. Symptoms of low battery charge include erratic responses 
when using the remote and a reduced range of operation.
Follow these steps to replace the batteries:
 1. Turn the remote face down in your hand.
 2. Slide the battery cover off the end of the remote.
 3. Remove the old batteries and dispose of them in an 
environmentally proper manner.
 4....

User Guide KODAK DP2900 Digital Projector 
50
Troubleshooting
If you don’t find the answer to your problem here, visit our Web site at 
www.kodak.com/go/projectors 
for the latest updates on 
troubleshooting.
Sound
Remote Control
Problem Cause and Solution
No sound. • Adjust volume.
• Verify audio / input connections.
• Adjust audio source.
Poor sound quality. • Make sure you are connected to the 
earphone jack on your laptop or line out 
jack on your desktop. 
• Make sure the volume setting on your...