Kodak Dp2900 Projector User Manual

Setting up the Projector
21
Connecting with an S-video cable:
 3.Plug the audio adapter’s white connector into the left “audio out” 
connector on your video source. Plug the adapter’s red connector 
into the right “audio out” connector on the video source.
 4. Plug the audio adapter’s white connector into the left “audio out” 
connector on your video source. Plug the adapter’s red connector 
into the right “audio out” connector on the video source. Plug the 
audio adapter’s other end into the audio...

User Guide KODAK DP2900 Digital Projector 
22
Starting the Projector
We recommend using a surge protector power strip when connecting 
your projector. 
&DXWLRQ $OZD\VXVHWKHSRZHUFRUGWKDWVKLSSHGZLWKWKH
SURMHFWRU
 1. Remove the lens cap.
 2. Plug the power cord into the side of the projector, then plug it into 
your electrical outlet. 
The fans start to run, and the Lamp LED on the top of the 
projector lights orange until the software has initialized. When 
initialization is complete, the Lamp...

Setting up the Projector
23
 5.Turn on your computer. Make sure your laptop’s external video 
port is activated; see “Portable and Laptop Activation Chart” on 
page 57 for details.
Note: With some computers, the order in which you power up the 
equipment is very important. Most computers should be 
turned on last, after all other peripherals have been turned on. 
Refer to your computer’s documentation to determine the 
correct order.
The computer image should display on the projection screen. If a 
video...

25
Using the Projector
This section describes how to use and make adjustments to the 
projector. It also provides a reference to the keypad and remote 
buttons and the options available from the on-screen menus.
Basic Image Adjustment
•Make sure you have turned on your equipment in the right order 
(page 22).
•If the image doesn’t display completely, zoom the image (page 26), 
adjust the height of the projector (page 26) or center the image by 
adjusting its horizontal or vertical position (page 37). Be...

User Guide KODAK DP2900 Digital Projector 
26
Adjusting the Projector
To focus the image, rotate the focus ring until the image is clear. To 
zoom the image, rotate the zoom ring. This adjusts the image size 
without affecting focus.
The projector is equipped with a self-locking, quick-release elevator 
foot and button.
To raise the projector:
 1. Press and hold the elevator button.
 2. Raise the projector to the height you want, then release the button 
to lock the elevator foot into position. 
focus...

Using the Projector
27
Using the Remote Control
,PSRUWDQW 7RFRQWUROWKHFRPSXWHU·VPRXVHIURPWKHSURMHFWRU·VUHPRWHRUNH\SDG
\RXPXVWFRQQHFWWKHPRXVHFRQQHFWRURQWKHFRPSXWHUFDEOHWRWKH
FRPSXWHU6HHSDJH IRUGHWDLOV
The projector ships with a remote control that has four function 
buttons, a disk mouse and two mouse buttons—one on the top of the 
remote and one on the bottom.
Point the remote control at the projection screen or at the front of the 
projector. The range for optimum...

User Guide KODAK DP2900 Digital Projector 
28
If you are creating presentations in MICROSOFT POWERPOINT, 
you can use the remote control mouse buttons to navigate through 
your presentation while in Slide Show mode. To configure the 
POWERPOINT program for this, choose Options from the Tools 
menu, click the View Tab, de-select the “Popup Menu on Right 
Mouse Click” option in the Slide Show section, then click OK. Then, 
when you’re in POWERPOINT Slide Show mode, a left click 
advances to the next slide...

Using the Projector
29
Using the Keypad and Remote Buttons 
While the menus are displayed, the volume, source, and standby buttons on 
the keypad act as menu navigation buttons. See “Using the On-Screen 
Menus” on page 32 for details.
The Keypad Buttons
The Remote Control Buttons
standby - turns off the 
image without turning 
off the projector source button - toggles 
back and forth 
between video and 
computer sourceslamp LEDlamp on/off
volume - 
decreases volumevolume - 
increases volume menu button -...

User Guide KODAK DP2900 Digital Projector 
30
Lamp on/off (keypad only) 
Press the lamp on/off button  to turn the lamp on or off. The Lamp 
LED indicates the state of the lamp. A green Lamp LED indicates that 
you can turn the lamp on, or the lamp is currently on. An orange LED 
indicates the software is initializing or the lamp is cooling. Do not 
press the 
lamp on/off button  when the LED is orange.
Menu 
Press the menu button  to open the on-screen menus. Press 
menu again to close the menus. When...