Kodak Dp2000 Projector User Manual

Using the Projector
25
Using the On-Screen Menus
The projector has seven drop-down menus that allow you to make 
image adjustments and change a variety of settings. Most of these 
adjustments aren’t available directly from the keypad.
Note: Some menu items may be grayed out at certain times. This 
indicates that the item is not applicable to your setup (for 
example, video standards do not apply to computer sources) 
or the item is not enabled until another selection is made (for 
example, Manual...

User’s Guide KODAK DP2000 Digital Projector 
26
Some submenus, such as Brightness, consist of a slider bar you use to 
increase or decrease a value. Some submenus, such as Standby Time, 
consist of options you scroll through to select the desired one. All 
changes are saved when you close the menus. 
To access another menu, use the up and down navigation buttons or 
the disk mouse on the remote control to move back to the top of the 
current menu, then use the left and right navigation buttons to move...

Using the Projector
27
Tint
The tint adjusts the red-green color balance in the projected image. 
Changing the Tint setting has no effect on PAL or SECAM video 
sources. 
•Press the left navigation button on the keypad to increase 
the amount of green in the image.
•Press the right navigation button on the keypad to increase 
the amount of red in the image.
Color
The color setting adjusts a video image from black and white to fully 
saturated color.
•Press the left mouse button to decrease the amount of...

User’s Guide KODAK DP2000 Digital Projector 
28
Image Menu

Auto Image
Note: Some screen savers interfere with the operation of Auto 
Image. If you’re experiencing problems, try turning your 
screen saver off, then turning Auto Image off and back on.
The projector automatically adjusts tracking, signal synchronization 
and vertical and horizontal position for most computers (Auto Image 
does not apply to video sources). If you want to adjust these features 
manually, you must turn off 
Auto Image first...

Using the Projector
29
Manual Sync
Note: The Manual Sync option is available only for computer 
sources. The projector sets this option automatically for a 
video source.
The projector adjusts signal synchronization automatically for most 
computers. But if the projected computer image looks fuzzy or 
streaked, try turning 
Auto Image off then back on again. If the image 
still looks bad, try adjusting the signal synchronization manually:
 1. Turn Auto Image off.
 2. Highlight Manual sync, then press the...

User’s Guide KODAK DP2000 Digital Projector 
30
Vertical position
Note: The Vert. Position option is available only for computer 
sources. The projector sets this option automatically for a 
video source.
Follow these steps to manually adjust the vertical position.
 1. Turn Auto Image off.
 2. Highlight Vertical position, then press the left navigation button 
to move the image down or press the right navigation button to 
move the image up.
Positioning adjustments are saved when you power off the...

Using the Projector
31
Standby Time
This option lets you select how long the lamp stays on and how long 
the blank screen is displayed in standby mode before the projector 
turns off. Select among 1, 5, 10, and 15 minutes and 1 and 2 hours by 
clicking the left or right navigation button and cycling through the 
options.
Rear Projection
When you turn 
Rear Projection on, the projector reverses the image so 
you can project from behind a translucent screen. Highlight Rear 
Projection, then click the left...

User’s Guide KODAK DP2000 Digital Projector 
32
Plug and Play
This setting toggles between On and Off. When it is On, most new 
computers will automatically recognize the projector, then set the 
monitor resolution and refresh rate accordingly. You need to set the 
Plug and Play setting to Off for the projector to display properly on 
some older computers. The Plug and Play setting does not affect 
video images.
If the projector’s display constantly changes between the computer 
image and the message,...

Using the Projector
33
Language Menu
You can display the on-screen menus in English, French, German, 
and Spanish. 
Move the cursor to the language you want, then click the left or right 
navigation button. The menus redraw immediately.
Status Menu
This is a read-only window for informational purposes. To display the 
status window, select Show status from the menu, then click the left 
or right navigation button. To remove the window, click the left or 
right navigation button. 

User’s Guide KODAK DP2000 Digital Projector 
34
Lamp hours used
Indicates how many hours the current lamp has been in use. The 
counter starts at zero hours and counts each hour the lamp is in use. 
Change the bulb when the brightness is no longer acceptable. See 
“Replacing the Projection Lamp” on page 38 for details.
Computer resolution 
Shows your computer’s resolution setting. To change this, go to your 
computer’s Control Panel and adjust the resolution in the Display tab. 
See your computer user’s...