Kodak Dp1100 Projector User Manual

Reference Manual KODAK DP900 / DP1100 
383/99
Standby Time
This option lets you select how long the lamp stays on and the 
blank screen is displayed when the projector enters standby mode 
before the projector turns off. Select among 1, 5, 10, and 15 
minutes and 1 and 2 hours by clicking either mouse button and 
cycling through the options.
Ceiling Projection
Note: To order the Ceiling Mount Kit, refer to “Optional 
Accessories” on page 60.
When you turn 
Ceiling Projection on, the projector turns the...

Using the Projector
3/9939
Plug and Play
This setting toggles between On and Off. When it is On, most 
new computers will automatically recognize the projector, then 
set the monitor resolution and refresh rate accordingly. You need 
to set the Plug and Play setting to Off for the projector to display 
properly on some older computers. The Plug and Play setting 
does not affect video images.
If the projector’s display constantly changes between the 
computer image and the message, “Perfecting the image”,...

Reference Manual KODAK DP900 / DP1100 
403/99
Language Menu
Figure 20 Language menu
You can display the on-screen menus in English, French, 
German, and Spanish. 
Move the cursor to the language you want, then click 
either mouse button. The menus redraw immediately.
Status Menu
This is a read-only window for informational purposes. To 
display the status window, select Show status from the menu, 
then click either mouse button. To remove the window, click 
either mouse button.
Figure 21 Status menu 

Using the Projector
3/9941
Lamp hours used
Indicates how many hours the current lamp has been in use. The 
counter starts at zero hours and counts each hour the lamp is in 
use. Change the bulb when the brightness is no longer acceptable. 
See “Replacing the Projection Lamp” on page 46 for details.
Computer resolution 
Shows your computer’s resolution setting. To change this, go to 
your computer’s Control Panel and adjust the resolution in the 
Display tab. See your computer’s user’s guide for details....

Reference Manual KODAK DP900 / DP1100 
423/99
Kodak Menu
Kodak’s exclusive Image Manager feature allows you to select 
the image display setting best suited for your specific 
presentation material and projection environment.
.
Image Manager Settings
Photo-PC Setting matches the higher contrast found on a 
standard PC monitor. This option is best for:
 images created on a PC
 images from a KODAK digital camera
 a starting point for composite or S-video inputs.
Photo-Mac Photo matches the lower...

Using the Projector
3/9943
Using the Image Manager
 1. Click the Kodak menu.
 2. Select the setting best suited for your presentation material 
and environment.
The new contrast setting is immediately applied to the image.
 3. Click OK to save the setting as your default Image Manager 
setting for the current and future presentations. 

3/9945
Maintenance &
Troubleshooting
This section describes how to:
 clean the lens
 replace the projection lamp 
 replace the batteries in the remote
 use the Kensington lock feature
 troubleshoot the projector
Cleaning the Lens
Follow these steps to clean the projection lens:
 1. Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
 Avoid using an excessive amount of cleaner.
 Abrasive cleaners, solvents or other harsh chemicals 
might scratch the lens.
 2. Lightly wipe the cleaning...

Reference Manual KODAK DP900 / DP1100 
463/99
Replacing the Projection Lamp

 
				
						
	%&					
			
	#	!	
			
	
		
	

 

					(			
			
	)&&&	
		*	

	
										

	

The lamp hour counter in the Status menu counts the number of 
hours the lamp has...

Maintenance & Troubleshooting
3/9947
 5. Loosen the two non-removable screws on the outside of the 
module.
Figure 23 Loosening the screws on the lamp module
 6. Slide the lamp connector to the right to disconnect it from the 
projector (Figure 24).
Figure 24 Sliding the lamp connector
 7. Remove the module (Figure 25). 

Reference Manual KODAK DP900 / DP1100 
483/99

 			
				
	
		
+	

			
			
Figure 25 Removing the lamp module
 8. Align the new lamp module in the correct direction.
 9. Gently push the module in as far as it goes.
 10. Tighten the screws on the outside of the module. 
 11. Slide the lamp connector to the left to re-attach it.
 12. Insert the tabs at the top of the lamp door into the projector 
and press the lamp door into place.
 13....