Kodak Dp1050 Projector User Manual

							When PAL/SECAM video is selected brightness,
contrast and saturation will be available. 
All options will be available for NTSC video. 
Select OK to save your changes and exit, or select
Cancel to exit without saving your changes.
Selecting Default restores factory settings.
Contents
31
1332 (ELEK). KODAK ENG  15.07.98  13:33  Side 31 
						

							Contents
327.3.2  Picture positioning Picture positioning 
Adjust vertical and horizontal position of the picture on
the screen with the two sliders.
Select OK to save your changes and exit, or select
Cancel to exit without saving your changes.
7.3.3   Audio controlAudio control
Select this function when you have connected an audio
signal to the ‘Audio in’ on the KODAK DP1050 ULTRA
connectors (or through the EVC cable). Use the four
sliders to adjust volume, bass, treble and balance until
you have a satisfying sound.
Select Internal Mute to mute the internal speakers.
Select External Mute to mute the external audio output.
Select OK to save your changes and exit, or select
Cancel to exit without saving your changes. 
Selecting Default restores factory settings.
1332 (ELEK). KODAK ENG  15.07.98  13:33  Side 32 
						

							Contents
337.3.4  Synchronization AdjustmentsSynchronization Adjustments
It is possible to adjust the synchronization in Computer
mode by adjusting the Phase and the Frequency. The
synchronization will be set by the automatic set-up
function. Manual sync adjustments should typically not
be required.
7.3.5  Color managerColor tone settings
The color manager is designed to give you maximum
performance from your KODAK DP1050 ULTRA projec-
tor, independent of ambient light conditions.  
In the color manager menu you can choose between
four pre-defined Color settings.
1332 (ELEK). KODAK ENG  15.07.98  13:33  Side 33 
						

							Contents
347.4  Product informationProduct information
Click on the product information icon in order to get
information about the product and company. 
Select Exit to leave the menu.
All maintenance should be done by 
KODAK authorized service personnel.
Contact your KODAK dealer for 
maintenance.
8. Maintenance
1332 (ELEK). KODAK ENG Z  12.08.98  13:47  Side 34 
						

							Contents35
9. What do I do if ( Trouble shooting)
1332 (ELEK). KODAK ENG  15.07.98  13:33  Side 35 
						

							Contents
36The image is not good (noise)
Possible causes and remedies:1.
The automatic image set-up is not activated. Run
auto set-up by pressing the green button on the
touch panel or run auto set-up from the menu.
2.
The synchronization on the PC is not set optimally. 
There is poor response from the Interactive 
Remote Control
Possible causes and remedies:
1.
Check that nothing is blocking the IR receiver at the
front of the KODAK DP1050 ULTRA.
2.
Make sure the remote is pointed towards the
screen.
3.
Make sure there is no more than 10m/33ft in
distance to the projector.
4.
Batteries might be low. Change batteries in the
remote control.
5.
Electromagnetic or optic noise may influence the
remote control. 
Turn off sharp fluorescent tubes, mobile phones etc
that are near the projector.No Image Appears
Possible causes and remedies:
1
.
The KODAK DP1050 ULTRA has not been
switched on. Check the ON/OFF switch at the back.
2.
There is no electricity in the power outlet in the
wall. Check that there is power in the power outlet.
NOTE! When all connections to electricity are OK,
there will be a green light at the control panel.
1332 (ELEK). KODAK ENG  15.07.98  13:33  Side 36 
						

							BEFORE YOU  START ................................................................2•
1.1 Color coding for ease of use .........................................2
•
1.2 Accessories .....................................................................3
•
1.2.1 Computer accessories for external PC/MAC .....3
•
1.2.2 Video accessories ................................................3
•
1.2.3 Other cables/accessories ....................................3
•
1.2.4 Optional cables and accessories .......................3
•
1.3 Insert batteries in the remote control ...........................5
Contents
1.
1332 (ELEK). KODAK ENG  15.07.98  13:33  Side 37 
						

							CONNECTING A VIDEO SOURCE TO THE 
KODAK DP1050 ULTRA .........................................................10•
4.1 Using external speakers...............................................11
Contents
4.
1332 (ELEK). KODAK ENG  15.07.98  13:33  Side 38 
						

							USING THE KODAK DP1050 ULTRA .....................................14•
6.1 Different program modes for the 
KODAK DP1050 ULTRA ................................................14
•
6.2 KODAK Remote control................................................15
•
6.3 Using the touch panel on the 
KODAK DP1050 ULTRA ................................................17
•
6.4 Adjusting the height and angle of the 
KODAK DP1050 ULTRA ................................................18
•
6.5 Adjusting Focus / Zoom ...............................................19
Contents
6.
1332 (ELEK). KODAK ENG  15.07.98  13:33  Side 39 
						

							USING THE MENU S.................................................................19
Contents
7.
1332 (ELEK). KODAK ENG  15.07.98  13:33  Side 40