Kodak Dp1050 Projector User Manual

							Contents
114.1 Using external speakersIn order to use external speakers with the KODAK
DP1050 ULTRA you need an amplifier. Connect the
amplifier to the audio out on the KODAK DP1050
ULTRA. When external speakers are connected, these can be
turned on or off from the KODAK DP1050 ULTRA. To
control the internal speakers, see section on Adjust
audio settings, section 7.3.3.Figure 10: Using external speakers
1332 (ELEK). KODAK ENG  15.07.98  13:33  Side 11 
						

							Contents
12A TV-tuner is optional for the 
KODAK DP1050 ULTRANOTE! Requires TV tuner to be installed.
In order to use the KODAK DP1050 ULTRA as a TV
output; connect the TV antenna to the TV connector on
the KODAK DP1050 ULTRA plug panel. The KODAK DP1050 ULTRA behaves just like a
normal TV. See the menus section 7.2.6 on how to
adjust the TV settings.
There are basically three ways of receiving the TV
signals to the KODAK DP1050 ULTRA:
u
Antenna (Terrestrial)
u
Cable 
u
Set-up box for satellite  
These three work differently and it is important to
consider the options of each when adjusting the
KODAK DP1050 ULTRA settings.
Antenna
When you adjust your TV to signals from an antenna
you must store each channel in a different program. .
The same is true for the KODAK DP1050 ULTRA TV-
tuner. When connected to an antenna you assign the
different channels to the programs in the Television
Setup Menu. Then you use the Up and Down arrows 
in the menu, remote control or the channel up/down
button on the control panel to switch between channels.
5. Connecting a TV- source to the 
KODAK DP1050 ULTRA
Figure 11: Connecting to TV- source
1332 (ELEK). KODAK ENG  15.07.98  13:33  Side 12 
						

							Contents13
1332 (ELEK). KODAK ENG  15.07.98  13:33  Side 13 
						

							Contents
146.1 Different program modes for the 
KODAK DP1050 ULTRAKODAK DP1050 ULTRA has different modes 
of operation:u
Stand-by mode
u
Normal mode
u
Quick mode
u
Menu mode
u
Pointer mode
u
Blank modeStand-by mode
In stand-by mode the projector is turned off and can be
turned on by using defined keys, see section 6.3
Normal mode
In normal mode a picture will be shown on the screen.
The mouse will function as a normal PC/MAC mouse.
Quick mode
Quick mode is used with the interactive remote control
(quick key). You assign functionality for the quick key
on the remote control in the quick menu (see section
7.2.5). When clicking on the Quick key you will be able
to switch between all the functions you have selected in
this menu.
Menu mode
In menu mode the menu system is activated and you
use the mouse pad and the mouse buttons on the
remote control to navigate in the menu. 
Pointer mode
In pointer mode you can move a pointer cursor on the
screen by using the mouse function.
Blank mode
In blank mode the screen is blanked out (black). 6. Using the KODAK DP1050 ULTRA
1332 (ELEK). KODAK ENG  15.07.98  13:33  Side 14 
						

							Contents
156.2 KODAK Remote controlThe KODAK Remote control has two purposes:1.
To access the Main Menu and control the various
image adjustments and utility functions of the
KODAK DP1050 ULTRA
2.
To allow remote control of your computer
Pointing it towards the projection screen operates the
remote control. An infra red beam bounces from the
screen to an infrared receiver on the KODAK DP1050
ULTRA.
NOTE!
Make sure nothing is blocking the IR receiver in
front of projector located beside the lens, as this
will prevent the communication between the remote
control and the KODAK DP1050 ULTRA.
To ensure smooth operation, the combined dis-
tance from the remote control to the screen and
back to the projector should not exceed 10 meters
(33 ft). If the distance via the screen is longer, you
should point the remote control directly towards
the IR receiver.The remote control works with Macintosh and with
Microsoft Windows, for interactive distance control of
your computer. A unique pressure-sensing pad on the
remote makes it very easy to control the computer and
to perform the exact same operations as you would
with a normal mouse.
Figure 12: Kodak remote control
1332 (ELEK). KODAK ENG  15.07.98  13:33  Side 15 
						

							Contents
16The Remote control is very easy to operate. It has only
six keys in addition to the pressure sensing mouse pad. 
The six keys are:
Key underneath the control
Left mouse key
Small gray key
Interrupt/break an action (right mouse key)
Menu
The menu key gives access to the KODAK menu con-
trol functions. To move within the various menu func-
tions, position the arrow cursor by pressing the sensi-
tive mouse pad and click with the left mouse button
which is located underneath the remote control.
If you are in menu mode and press the menu key you
will return to normal mode
Zap
The two zap keys can be programmed to perform an
assigned function. To assign a function to the zap keys,
select the Zap icon from the menu. The zap keys can
be programmed to do the same function e.g. volume
up/down. See section 7.2.5 for further explanations of
the zap menu.Quick
When pressing the Quick key you can switch between
all selected functions for the Quick key. See section
7.2.4 for how to select functions for the Quick key.
Figure 13:  The remote mouse communicates with the 
KODAK DP1050 ULTRA projector via 
the projection screen
1332 (ELEK). KODAK ENG  15.07.98  13:33  Side 16 
						

							Contents
176.3 Using the touch panel on the 
KODAK DP1050 ULTRA
The touch panel gives you direct access to the most
important functions of the KODAK DP1050 ULTRA. It is
very handy to use when the remote control has low
batteries, or you simply have forgotten to bring it with
you. The key functions are as follows:
Source
The KODAK DP1050 ULTRA has direct keys for four
sources:
Functionality Text/coloru
Computer (PC/MAC)  (PC)  
u
TV (TV)   
u
Composite video (V)  
u
S-video (S-V)  
The TV source button will only work when a 
TV-tuner is installed.
CHAN
PC
TV
S-VV
Figure 14:  The keys on the touch panel on the 
KODAK DP1050 ULTRA projector
1332 (ELEK). KODAK ENG  15.07.98  13:33  Side 17 
						

							Contents
18Volume (+/-)
The Volume key is used to control the sound level
when the KODAK DP1050 ULTRA is connected to an
audio source.
Channel  
Click on the arrows left/right to switch between 
pre-programmed TV channels when TV is 
selected as source.    
Brightness
The Brightness key is used to control the brightness in
data and video image.
Contrast
The Contrast key is used to control the contrast in data
and video image.
Stand by
The stand by key will set the KODAK DP1050 ULTRA
in stand by mode. The lamp will turn off, and the fans
will run for a little while cooling the projector before
stopping. To return to normal mode, press the Stand by
key once more, or press the Menu key on the remote
control.Automatic set-up
The automatic set-up key will set up the projector with
optimal settings for the connected source. If you want
to do manual adjustments you can do this by using the
menus (see section 7). 
Note!
You can not access the screen menu 
system without the remote control.
6.4 Adjusting the height and angle of 
the KODAK DP1050 ULTRAYou can adjust the height and angle of the KODAK
DP1050 ULTRA by adjusting the four small feet under-
neath the product. 
NOTE!
The KODAK DP1050 ULTRA should never be left
with an angle of more than 15 degrees over a
longer period of time. This will shorten the 
lifetime of the lamp.
1332 (ELEK). KODAK ENG  15.07.98  13:33  Side 18 
						

							Contents19
7. Using the menus
TVPC
Main menu. 
1
2
1332 (ELEK). KODAK ENG  15.07.98  13:33  Side 19 
						

							Contents
207.1.1 Main menuThe main menu is divided into two parts:u
Icons
u
Help text
Icons
The icons illustrate a function and are grouped into
groups with similar functionality. Clicking an icon acti-
vates it. Some icons have a direct function and some
will activate a second level menu.
Help text
By moving the cursor over the icons the text area will
give a short description of the icon.Stand by
This function sets the projector in 
stand-by mode
Auto set-up
Auto set-up will do automatic set-up of the projector:
u
Horizontal and vertical position
u
Sampling clock
u
Phase
u
Chooses between available video formats and
NTSC/PAL auto detection
1332 (ELEK). KODAK ENG  15.07.98  13:33  Side 20