Kodak Dp1050 Projector User Manual

Contents
114.1 Using external speakersIn order to use external speakers with the KODAK
DP1050 ULTRA you need an amplifier. Connect the
amplifier to the audio out on the KODAK DP1050
ULTRA. When external speakers are connected, these can be
turned on or off from the KODAK DP1050 ULTRA. To
control the internal speakers, see section on Adjust
audio settings, section 7.3.3.Figure 10: Using external speakers
1332 (ELEK). KODAK ENG  15.07.98  13:33  Side 11 

Contents
12A TV-tuner is optional for the 
KODAK DP1050 ULTRANOTE! Requires TV tuner to be installed.
In order to use the KODAK DP1050 ULTRA as a TV
output; connect the TV antenna to the TV connector on
the KODAK DP1050 ULTRA plug panel. The KODAK DP1050 ULTRA behaves just like a
normal TV. See the menus section 7.2.6 on how to
adjust the TV settings.
There are basically three ways of receiving the TV
signals to the KODAK DP1050 ULTRA:
u
Antenna (Terrestrial)
u
Cable 
u
Set-up box for satellite  
These...

Contents13
1332 (ELEK). KODAK ENG  15.07.98  13:33  Side 13 

Contents
146.1 Different program modes for the 
KODAK DP1050 ULTRAKODAK DP1050 ULTRA has different modes 
of operation:u
Stand-by mode
u
Normal mode
u
Quick mode
u
Menu mode
u
Pointer mode
u
Blank modeStand-by mode
In stand-by mode the projector is turned off and can be
turned on by using defined keys, see section 6.3
Normal mode
In normal mode a picture will be shown on the screen.
The mouse will function as a normal PC/MAC mouse.
Quick mode
Quick mode is used with the interactive remote control
(quick...

Contents
156.2 KODAK Remote controlThe KODAK Remote control has two purposes:1.
To access the Main Menu and control the various
image adjustments and utility functions of the
KODAK DP1050 ULTRA
2.
To allow remote control of your computer
Pointing it towards the projection screen operates the
remote control. An infra red beam bounces from the
screen to an infrared receiver on the KODAK DP1050
ULTRA.
NOTE!
Make sure nothing is blocking the IR receiver in
front of projector located beside the lens, as this...

Contents
16The Remote control is very easy to operate. It has only
six keys in addition to the pressure sensing mouse pad. 
The six keys are:
Key underneath the control
Left mouse key
Small gray key
Interrupt/break an action (right mouse key)
Menu
The menu key gives access to the KODAK menu con-
trol functions. To move within the various menu func-
tions, position the arrow cursor by pressing the sensi-
tive mouse pad and click with the left mouse button
which is located underneath the remote control.
If...

Contents
176.3 Using the touch panel on the 
KODAK DP1050 ULTRA
The touch panel gives you direct access to the most
important functions of the KODAK DP1050 ULTRA. It is
very handy to use when the remote control has low
batteries, or you simply have forgotten to bring it with
you. The key functions are as follows:
Source
The KODAK DP1050 ULTRA has direct keys for four
sources:
Functionality Text/coloru
Computer (PC/MAC)  (PC)  
u
TV (TV)   
u
Composite video (V)  
u
S-video (S-V)  
The TV source button...

Contents
18Volume (+/-)
The Volume key is used to control the sound level
when the KODAK DP1050 ULTRA is connected to an
audio source.
Channel  
Click on the arrows left/right to switch between 
pre-programmed TV channels when TV is 
selected as source.    
Brightness
The Brightness key is used to control the brightness in
data and video image.
Contrast
The Contrast key is used to control the contrast in data
and video image.
Stand by
The stand by key will set the KODAK DP1050 ULTRA
in stand by mode. The...

Contents19
7. Using the menus
TVPC
Main menu. 
1
2
1332 (ELEK). KODAK ENG  15.07.98  13:33  Side 19 

Contents
207.1.1 Main menuThe main menu is divided into two parts:u
Icons
u
Help text
Icons
The icons illustrate a function and are grouped into
groups with similar functionality. Clicking an icon acti-
vates it. Some icons have a direct function and some
will activate a second level menu.
Help text
By moving the cursor over the icons the text area will
give a short description of the icon.Stand by
This function sets the projector in 
stand-by mode
Auto set-up
Auto set-up will do automatic set-up of the...