Kodak Dp 800 Projector User Manual

							Contents
51Using the menusThe TV-Tuner can be purchased as an
optional add-on to the Projector. You can
easily install the TV-Tuner yourself. See fig. 15.
This user manual will, in connection with the
main user manual for the Projector, give you
all the information necessary to operate the
TV-Tuner.Enter the MAIN MENUWith the Interactive Remote Control, or the Control
Panel, press the MENU key to get the MAIN MENU.
Then use the pressure sensing pad to move the mouse
pointer to a menu icon and click the button (left mouse)
underneath the Interactive Remote Control or the Enter
key of the Control Panel. You click once to select the
icon, and once more to activate it. If the icon has a level
2 window, this will now appear on the screen. You may
change the settings in the level 2 window.1.If you click OK you store the displayed settings and
exit from the menus.
2.If you click Cancel you discard any changes you
made to the settings in the current level 2 window,
and return to the MAIN MENU.
9 Projector: TV-Tuner
Fig. 15,  Changing/installing the TV-Tuner card 
						

							Contents
52How to Change the settingsRead the section in the main user manual (page 30) on
adjusting the settings in a level 2 window. In the chapter
on the TV-Tuner Setup Menu we will explain in detail
how to use this specific menu.Removing the MAIN MENUTo remove the MAIN MENU from the screen press the
MENU key on the Interactive Remote Control, or on the
Control Panel of the Projector. It will also automatically
disappear after 20 seconds.If a TV-Tuner is installed in your Projector, you can see
the above icon in the Source section of the MAIN
MENU. If you activate this icon the Projector will tell you
that you have selected TV-Tuner as source. To enter the
TV-Tuner menu you simply press the MENU key again.
You will now see the TV-Tuner addition to the MAIN
MENU.
TV-Tuner  
						

							Contents
53Above you see the MAIN MENU with the 
TV-Tuner icons present.
Activating this icon will open the TV-Tuner Setup Menu
where you can adjust the TV-Tuner settings.
Select the above icon from the MAIN MENU. You will
get the window below.The TV-Tuner Setup Menu has five main parts:
TV System:
First you should select the right TV System for your
tuner. In the TV Systems section you can choose
between the following two systems:
West Europe
USA
Use the up or down arrows to scroll and select between
the different systems.TV-Tuner MAIN MENU
TV-Tuner settings  
						

							Contents
54TV Program:
Here you can program your TV channels. Using the up
and down arrows you can select between programs 1 -
30. Each of these programs can be assigned to TV
channels.
Assign button:
If this button is pushed the TV Channel shown will be
assigned to the TV Program shown. The User will get
feedback in the form of a TV Channel name change in
the TV Program box (if there is a change), and that
arrows above and under the assign button gives a short
green blink.
TV Channel Name:
The channel frequencies will have different names
depending on your TV System, and the names shown
are the technical names for the channel frequencies.
This means that you cannot find the publicly known
name of TV channel you are looking for, but you should
use the up and down arrows to scroll the channels.
When you get to a channel that you would like to have
easy access to you can assign it to the current TV Pro-
gram (1 - 30) by pressing the assign button. Go through
all of the channels and assign up to 30 programs for
easy access.Close button:
When you are finished adjusting the TV-Tuner settings
you press this button to leave the menus. The channel
programmed at the currently shown TV Program will be
shown on your screen.
Select the above icon from the MAIN MENU. You will
get the window below.
TV Program menu:
When you have assigned TV Channels to your different
TV Programs you can enter the TV Program menu by
activating the TV Program icon in the MAIN MENU. This
will bring up a small menu consisting only of a number
and up and down arrows. You move through your
assigned TV Programs by using the arrows. You can
TV-program menu  
						

							Contents
55also use the LEFT and RIGHT arrows in the Control
Panel to move between channels. This menu will not
dissappear until closed by the user, so you can keep it
on the screen for as long as you want. If you want to
close the menu you just press Menu on the interactive
remote control or the touch panel.Operational TipsThe Projector TV-Tuner will behave just like a normal
TV. This means that you should consider the following
when adjusting the TV-Tuner settings:
Source of TV signals
There are basically three ways of taking in the TV
signals to the Projector.u
Antenna
u
Cable
u
Satellite dish
These three work differently, and it is important to
consider the options of each when adjusting the Projec-
tor TV-Tuner settings.Antenna:
When you adjust your TV to signals from an antenna
you must store each channel in a different location
meaning that you must switch channels on the TV itself.
The same is true for the Projector TV-Tuner. When
hooked up to an antenna you assign the different chan-
nels to the programs in the TV-Tuner Setup Menu. Then
you use the Up and Down arrows in the menu to go
from one channel to another.
Cable:
When you are connected to a cable system you can
have two options. If you have a cable decoder you set
your TV to the channel for the cable, and then you use
the remote control for the decoder to switch between
channels. If you do not have a decoder you simply set
your TV up just like you would with an antenna. This is
also the same with the Projector. You must scroll the
channel name in the TV-Tuner Setup Menu until you
find the correct channel for your cable system. When
this channel has been assigned to one of the program
numbers you simply select this program and use your
decoders remote control to switch between channels. 
						

							Contents
56Satellite dish:
This works like the cable decoder meaning that you
easily select the channel that reads the signals from the
satellite dish, and then you use the decoders remote
control to switch between channels. Follow the
explanation under cable to set up the correct channel,
and then use your decoder for the satellite dish to
switch between the different channels.
Follow the instructions in the TV-Tuner Setup Menu to
assign channels to the different TV Programs.
Programming ChannelsYou are free to program the different TV Programs to
the number you want from 1 - 30.
The chosen programming will stay in place even if you
move the Projector, as long as the programs are locked
to that channel. Channel locations might be different in
different areas, and also wether you are receiving from
antenna, cable or satellite dish. 
						

							Contents
57Aadjust picture position, .......34 
adjust Zoom / Focus ..........35
adjusting brightness, ..........31 
adjusting contrast, .............31
advanced picture 
adjustments ....................38
alternative picture mode ....39
audio adjustments,............44
automatic system setup .....36 Bbalance, ............................44 
bass, .................................44 
batteries, changing,  ..........46 
brightness, ........................30 
brightness, adjusting,  ........31 Cceiling mounting,  ...............37 
change settings, menus,  ...30 
changing batteries,  ...........44 
changing bulb, ...................46 
changing fuses, .................48 
choose Menu Language,  ..39 
colourmode, ......................32 
composite video, 
connecting ......................11 
selecting, .......................42 
using, .............................11 
compress image,VGA,  ......35 
compress image,SVGA, ....36 connecting
to a Apple Macintosh 
desktop computer,  ...........9 
to a desktop PC,  ..............9 
to a laptop or notebook, .10 
to a video player,  ...........11 
to an Apple Macintosh 
Powerbook, ....................10 
contrast, ............................31 
contrast, adjusting, ............31 
control panel,  ....................26 
cooling, .............................14 
cooling fan,  .......................14
Eexpand image VGA  ...........35
expand image SVGA  ........36
external computer, 
selecting, .......................42 Ffan, cooling,  ......................14 HHardcase ............................5 
I
image compressing, ..........35 
interactive remote 
control, ...........................15 
driver software,  ..............21
keys, ..............................16 IR receiver, ........................15
Info, product, suport  ..........41 
Llanguage, choosing menu..39 
light conditions,  .................13 
lamp time ...........................40 Mmenus
change settings,  ............30 
MAIN MENU,  .................28 
MAIN MENU functions,  .31 
removing, .......................30
overview ........................29
microphone select/
deselect .........................45PPAL video,  .........................32 
picture mode ......................39
picture orientation,  ............37 
picture position, 
adjusting, ........................34 
pressure sensing 
mouse pad,  .....................17 
projection screen,  .............14 Rremove MAIN MENU,  .......30 
resolution, VGA,  ................35 
resolution, SVGA,  .............36 
RGB Out,  ............................9 
Ssaturation, .........................32 
screen resolution,VGA  ......35
screen resolution,SVGA  ...36 
spare parts, .......................48 
S-video, .............................12 
using, .............................12
standby ..............................42 
system setup, ....................36 
Scart video .........................12 Ttest picture,  .......................42 
tint, ....................................32 
treble, ................................44
TV-tuner .............................51
main menue,  ..................53 
setings ............................53
setup menu
Tv-program menue Vvolume, .............................44 Wwarranty card,  .....................7 ZZAP button,  .......................41 
INDEX 
						

							•
IDENTIFYING THE DIFFERENT PARTS OF THE 
PROJECTOR
.......................................................................5
•
Before you start ....................................................................5
Contents 
						

							•
CONNECTING THE  PROJECTOR 
PROJECTOR TO YOUR  COMPUTER
..............................8
•
Connecting to a desktop computer ....................................9
•
Connecting to an Apple Macintosh desktop computer ....9
•
Connecting to a standard laptop, notebook ....................10
•
Connecting to an Apple Macintosh Powerbook ..............10
Contents 
						

							•
CONNECTING THE  PROJECTOR 
PROJECTOR TO YOUR VIDEO  PLAYER
.....................11
•
Using composite video ......................................................11
•
Using Scart video ...............................................................12
•
Using S-video......................................................................12
Contents