Kodak Dp 800 Projector User Manual

							Contents
31The MAIN MENU functionsThis icon will only appear when connected to a
computer source.
Select the above icon from the MAIN MENU. You will
get the window below.Adjust brightness and contrast with the two slider
controls. If you want the Projector always to use the
optimal contrast, switch on the check box “Auto con-
trast”. When the check box is on it is not possible to
adjust the contrast with the slider.
Colour Managerwhich is a system where you can
select how you want the Projector to treath colours.
We have programed the Projector for four different
modes which are:
True colours, High brightness, Warm colours I and
Warm colours II.
Select the Colour Manager mode you wish to use.
Select OK to save your changes and exit, or select
Cancel to exit without saving your changes.
Adjusting brightness and contrast 
						

							Contents
32This icon will only appear when connected to a video
source.
Select the above icon from the MAIN MENU.
You will get one of the windows below depending on
the video system connected.
The window above is the one you get if you have
connected NTSC video standard as source, and the
window to the left is the one you get if you have con-
nected PAL or SECAM video standards as source. In
these windows you can adjust four video parameters,
tint (only in NTSC), saturation, brightness and contrast.
Adjust the sliders until the screen image looks satis-
fying, or choose Default to get a predefined setting.
In the PAL/SECAM window you also have checkboxes
for each system. The default setting is PAL, so if you 
Adjust image settings
Adjust image settingsAdjust image settings 
						

							Contents
33need to show SECAM video you must change this
setting by clicking in the SECAM box.
Both windows have the Colour Manager which is a
system where you can select how you want the
Projector to treat colours. We have programed the
Projector for four different modes which are:
True colours, High brightness, Warm colours I and
Warm colours II.
Select the Colour Manager mode you wish to use.
Select OK to save your changes and exit, or select
Cancel to exit without saving your changes.This icon will only appear when connected to a
computer source.
Select the above icon from the MAIN MENU. You will
get the window below.
Use this function to synchronize the Projector with the
source if you have flicker in the picture.
Adjust product/source 
synchronization
Adjust product/source synchronization 
						

							Contents
34Select the above icon from the MAIN MENU. You will
get the window below.Adjust vertical and horizontal position of the picture on
the screen with the two sliders. If you want the Projector
always to select the optimal position, switch on the
check box Auto position. When this check box is on it
is still possible to adjust the position with the two slid-
ers. This will result in the auto position function being
disabled.
NB!  The auto position is only available with a 
computer as source.
Select OK to save your changes and exit, or select
Cancel to exit without saving your changes.
Adjust picture position
Adjust picture position 
						

							Contents
35Select the above icon from the MAIN MENU. You will
get the window below.
In this window you can adjust the Zoom and Focus of
the Projector by clicking on the up and down arrows in
the menu. When you have adjusted the image to your
satisfaction click on the CLOSE button to exit and save
your new settings.
Projector VGA:One of these icons will appear if resolution is higher or
lower than 640x480.
Select one of the above icons from the MAIN MENU.
This function will expand or compress the screen image
vertically. This is useful if you are displaying software
that has lower resolution than 640x480 or PAL video
with resolution higher than 640x480.
If you have expanded the image and want to compress
it, select the compress icon.
If you have compressed the image and you want to
expand it, select the expand icon.
Zoom / Focus Adjustments
Expand / compress 
image vertically 
Zoom / Focus Adjustments 
						

							Contents
36Projector SVGA:One of these icons will appear if resolution is  lower
than 800x600.
Expand image
If you have a computer resolution of less than 800 x
600, or a NTSC Video image you can expand it to fill
the screen by clicking on the expand icon.
If you have expanded the image and want to compress
it, select the compress icon.
Compress image
If you have a higher computer resolution than 800 x
600 the image will allways be shown in compressed
mode and none of the icons will apear.Select the icon above to run an automatic system
setup. This optimizes the Projectorsettings to fit the
selected source.
Expand / compress 
image vertically 
Run automatic system setup 
						

							Contents
37The Projector is designed for rear projection and ceiling
mounting upside down. These adjustments let you
easily set up the correct image for your application.
Select the above icon from the MAIN MENU. You will
get the window below.Switch on the leftmost check box to rotate the screen
image 180° (front ceiling mounting). Switching on the
rightmost check box will mirror the screen image (rear
projection). Switch on both for rear ceiling mounting.
Select OK to save your changes and exit, or select
Cancel to exit without saving your changes.
Change picture orientation
Change picture orientation 
						

							Contents
38Projector:When you select this icon you get the window below.In this window you can tune the values for the parame-
ters Htot, Hsize and Vsize.
The Projector has 15 different set-ups to choose, 
and will automatically configure the Projector to the
correct mode.
The purpose of these Advanced Adjustments is that
you, as a user can manually override all parameters,
and fine tune settings to make them fit your particular
application exactly. This is very useful if you, eg. have a
scaleable graphics board.
NB! If you find, that adjusting the parameters here
reduces image quality, press DEFAULT to return to
factory settings.
NB! Make sure both the Hsync and Vsync values
are within the Projector specifications.
Advanced picture adjustments
Advanced picture adjustments 
						

							Contents
39Select the above icon from the MAIN MENU. You will
get the window below.
Click on the icon with the flag representing the lan-
guage you want to use. The window will disappear, and
the selected language will be used in the MAIN MENU
and in all the level 2 windows.This icon will only appear if alternative picture mode is
available.
You will have the option of selecting an alternative
picture mode, if the system recognizes a graphics
mode which has the exact characteristics of a different
mode, and where the system is not able to distinguish
between the two. An example of 2 modes which have
identical characteristics is VGA text (720x400
resolution) and VGA 320x200 graphics.
Select the above icon to change to an alternative
picture mode.
Choose menu language
Change to alternative picture mode
Choose language 
						

							Contents
40Selecting the above icon gives you the window below.
In this window you can see the accumulated time that
the lamp has been used. You also use this window to
reset the accumulated lamp time when you have
changed the lamp.
The lamp reset indicator and the whole lamp replace-
ment mechanism of the Projector  is designed with user
convenience in mind, eliminating the need for costly
service calls.
Show accumulated lamp time
Show accumulated lamp time
WARNING! Do not reset the lamp indicator
unless you have just installed a new lamp
Resetting the lamp when it is not warranted
may cause you to use the lamp longer than
recommended, and may cause damage to
the Projector