Keurig 10 Manual

							USE & CARE GUIDE  
						

							2 3 
When using electrical appliances, basic 
safety precautions should be followed, 
including the following:
 1. Read all instructions before using.
 2.  Do not touch hot surfaces. Use 
handles and knobs when available.
 3. This appliance must be properly 
installed and located in accordance 
with these instructions before   
it is used.
  4.  The use of accessory attachments 
not recommended by the appliance 
manufacturer may result in fire, 
electrical shock, or injury   
to persons.
  5. Do not place on or near a hot   
gas or electric burner, or in a 
heated oven.
  6. Do not use outdoors.
  7.  To protect against fire, electric 
shock, and injury do not immerse 
cords, plugs, or the appliance in 
water or any other liquid.
 8. Do not fill the Water Reservoir 
above the MAX FILL line.
  9.  Use only water in this appliance!  
Do not put any other liquids or 
foods in the Water Reservoir 
except as instructed in the cleaning 
instructions in this guide.
  10.  Turn off and unplug the brewer 
before cleaning or maintenance. 
Allow to cool before putting on 
or taking off parts and before 
cleaning the appliance.
 11. For best operation, plug the 
appliance into its own electrical 
outlet on a dedicated circuit to 
prevent flickering of lights,   
blowing of fuses, or tripping   
a circuit breaker.
  12. Do not operate any appliance with 
a damaged Power Cord or plug or 
after the appliance malfunctions 
or is damaged in any manner. 
Contact Keurig Customer Service 
to report any malfunction of or 
damage to the brewer.
  13. Do not let the Power Cord hang 
over the edge of the table or 
counter, or touch hot surfaces.
 14. To disconnect, press the Power 
Button on the brewer to “OFF” 
status and then remove the plug 
from the wall outlet.
 15. Close supervision is necessary 
when any appliance is used by or 
near children.
 16. Do not lift the brewer handle while 
brewing is in progress.
IMPORTANT SAFEGUARDS 
  1 7.  Always keep the Water Reservoir 
Lid on the Water Reservoir unless 
you are refilling it.
 18. This appliance is equipped with a 
Power Cord having a grounding 
wire with a grounding plug.   
The appliance must be grounded 
using a 3-hole properly grounded 
outlet. In the event of an electrical 
short circuit, grounding reduces 
the risk of electrical shock.
  19.  If the outlet is a standard 2-prong 
wall outlet, it is your personal 
responsibility and obligation to 
have it replaced with a properly 
grounded 3-prong wall outlet.
  20.  Do not, under any circumstances, 
cut or remove the third (ground) 
prong from the Power Cord or use 
an adapter.
 21. Consult a qualified electrician if 
the grounding instructions are not 
completely understood, or   
if doubt exists as to whether the 
appliance is properly grounded.
 22. Do not use the appliance for other 
than its intended use. WARNING TO USERS 
 
AND PARENTS:
 
1.  DO NOT  permit children to use 
the brewer unless there is adult 
supervision. Brewer dispenses very 
hot water.  
2.  SPECIAL NOTICE FOR 
HOT COCOA/OTHER USERS: 
IMMEDIATELY AFTER USING 
A HOT COCOA/OTHER POD, 
RUN A HOT WATER BREW 
CYCLE  without a pod to avoid 
the possibility of clogging the exit 
needle.  DO NOT  assume the next 
user will do this.
SAVE THESE 
INSTRUCTIONS.
WARNING
!
RISK OF FIRE OR  
ELECTRIC SHOCK  
DO NOT OPEN
WARNING: TO REDUCE THE RISK OF  FIRE OR ELECTRIC SHOCK, DO NOT 
REMOVE THE BOTTOM COVER. NO USER 
SERVICEABLE PARTS ARE INSIDE. REPAIR  SHOULD BE DONE BY AUTHORIZED  SERVICE PERSONNEL ONLY. 
						

							4 5 
CAUTION: There are three sharp 
needles that puncture pods, two 
above the Pod Holder and the  
other in the bottom of the Pod 
Holder. To avoid risk of injury, do 
not put your fingers in the Pod 
Holder Assembly.
CAUTION: There is extremely hot 
water in the Pod Holder during 
the brew process. To avoid risk of 
injury, do not lift the Handle or 
open the Pod Holder Assembly 
during the brewing process.
CAUTION: Please always keep the  
brewer in its upright position to 
avoid potential injury and/or 
damage to your brewer.
CAUTION: Very hot liquid. Adult 
supervision required.
SHORT CORD INSTRUCTIONS:   
A short power supply cord is 
provided to reduce the risk of 
becoming entangled in or tripping 
over a longer cord. Longer 
detachable power-supply cords or 
extension cords are available and 
may be used if care is exercised 
in their use. If an extension cord 
is used, (1) the marked electrical 
rating of the cord set or extension 
cord should be at least as great 
as the electrical rating of the 
appliance; (2) the cord should be  arranged so that it will not drape over 
the countertop or tabletop where it 
can be pulled on by children or tripped 
over unintentionally; and (3) the 
extension cord must include a 3-prong 
grounding plug.
THIS PRODUCT IS FOR HOUSEHOLD 
USE ONLY.
WARNING 
 
THIS PRODUCT CONTAINS 
CHEMICALS, INCLUDING LEAD, 
WHICH IS KNOWN TO THE STATE 
OF CALIFORNIA TO CAUSE CANCER,  BIRTH DEFECTS, OR OTHER REPRODUCTIVE HARM.
KEEP ALL PLASTIC BAGS AWAY  FROM CHILDREN
USER GUIDE TABLE OF CONTENTS
KEURIG
® CLASSIC SERIES
Features 6
Controls & Indicators  7
Unpacking Instructions  8
SECTION 1
Setup 10
Brew Your First Cup  12
SECTION 2
Controls & Indicators 14
Caring For Your Brewer   15
SECTION 3
Troubleshooting 22
SECTION 4
Warranty 24
SECTION 5
Helpful Hints  26 
						

							6 7 
FEATURESCONTROLS & INDICATORS
K200 SERIES BREWER 
 A.
 Water Reservoir Lid
  B.  MAX Fill
 C.  Water Reservoir
  D.  Ve nt
  E.  Water Reservoir 
Lock Tab Slots
  F.  Housing  P.
 Add Water Light (Blue)
 Q.  Descale Light (Red)
R.  Heating Light (Red)
 S.  Auto Off Light (Green)
 
G.  Power Cord
 H. Handle
 I. Lid
  J.  K-Cup® Pod Holder   
(J and K are the K-Cup®   
Pod Holder Assembly)  T.
 Auto Off Button
 U.  Power Light (Green)
 V.  Power Button
W.  Large Mug Button
 
K.  Funnel
  L.  K-Cup® Pod   
Assembly Housing
  M.  Drip Tray Plate
  N.  Drip Tray
  O.  Drip Tray Base  X.
 Small Mug Button
 Y.  Small Cup Button
For replacement parts, please visit www.Keurig.com
B
A
C
E H
P
Q
R
S
T
U
V
W
X
Y
I
J
K
L
M
N
O
G D
F   
						

							8 9 
UNPACKING INSTRUCTIONS
1 |
 LET’S GET BREWING!
1.  Place brewer box on a large steady surface (such as a table or 
countertop) or on the floor. Open the box.
2.  Remove enclosed literature.
3.  Turn the box on its side with front of box face down.
4.  Reach into the box and grasp the plastic bag that contains the brewer.
5.  Carefully pull the plastic bag (and packaging materials) toward you 
and out of the box. The brewer will still be encased in the polyfoam 
and be on its side.
6.  Remove the top polyfoam packaging material.
7.   Carefully lift brewer off of the bottom polyfoam and place it upright 
on a flat, steady surface.
8.  Lift plastic bag off of brewer.
9.   Record the serial number for this brewer on page 5 of this guide. The 
serial number can be found on the bottom of the brewer box or on the 
brewer behind the Drip Tray (when removed).
10.  Place the brewer upright on a flat, steady surface. Remove tape 
holding Water Reservoir in place. 
We recommend you save all packing materials in case future shipping of 
the product is necessary.
IMPORTANT:  You cannot use your Keurig® brewer until it has been set up 
for its first use.
NOTE: If brewer has been exposed to temperatures below freezing, allow 
brewer at least two hours to reach room temperature before brewing.   
A frozen or extremely cold brewer will not operate.
WARN I N G :   
Keep all plastic bags away   
from children.  
						

							1011
SETUP
2. Place a large mug (10 oz. minimum) on   
the Drip Tray Plate.
3.  Remove the Water Reservoir from 
brewer by first removing Lid from 
Reservoir, then lifting Reservoir straight 
up and away from brewer (may be 
tight). Rinse with fresh water. Fill Water 
Reservoir with bottled or filtered   
water so that the water is to and not 
beyond the MAX FILL line. 5. 
Press Power Button found on upper right 
panel of the brewer. The green Power 
Light will illuminate.  
NOTE: A K-Cup® pod should not be used for this sequence. NOTE: If the Water Reservoir is empty or not in place on the 
brewer, the blue Add Water Light will illuminate. The Small  
Mug Button will not be activated until water is added to the 
Water Reservoir.
4. Place Water Reservoir base into the left 
side of the brewer and be sure the Water 
Reservoir Lock Tabs engage with the 
brewer. Replace Lid on Water Reservoir. 6. 
The brewer will automatically fill with 
water and then the water will be heated. 
This will take about 4 minutes. During the 
heating period, the red Heating Light will 
illuminate. Once the water is heated, the 
red Heating Light will turn off and the 
Small Cup, Small Mug, and Large Mug 
Buttons will illuminate.   
NOTE: Do not lift Handle during this 
heating period.   
NOTE:  You may see small amounts 
of water coming from the Vent and 
dripping into the Water Reservoir 
during this and subsequent heating – 
this is normal.
1  |
 LET’S GET BREWING!
1.  Unwrap cord and plug the brewer into   
a grounded outlet. Remove all pieces of   
packing tape.
7.  Lift and lower the Handle. Press the 
Small Mug Button to start a cleansing 
brew. Pour the hot water into the sink. 8. 
The brewer may take 15 seconds to 
reheat water between brews during 
which time the red Heating Light may be 
illuminated. When the water has heated, 
the red Heating Light will turn off. The 
one-time setup process is now complete 
and you are ready to brew!   
						

							1213
1 |
 LET’S GET BREWING!
BREW YOUR FIRST CUP
1.  The green Power Light will illuminate to   
indicate the brewer is powered on. Place 
a cup or mug on the Drip Tray Plate. 2.
 Lift the Handle and the K-Cup® pod 
Holder will open toward you. Select   
a K-Cup® pod.
NOTE: Do not remove the foil lid or puncture the K-Cup® pod.
3.  Place a K-Cup® pod in the K-Cup®   
Pod Holder. Lower the Handle completely 
to close the Lid.
CAUTION: There are two sharp needles that puncture the 
K-Cup® pod, one above the K-Cup® Pod Holder and the other in 
the bottom of the K-Cup® Pod Holder. To avoid risk of injury, do 
not put your fingers in the K-Cup® Pod Holder.
4.  Select your brew size: The Small Cup 
choice will yield a 5.25 oz. serving, the 
Small Mug will yield a 7.25 oz. serving and 
the Large Mug will yield a 9.25 oz. serving. 
The blue Brew Button you choose will 
remain illuminated while brewing.
NOTE: If you do not push a Brew Button in 60 seconds, the  
Brew Buttons will be disabled to prevent accidental activation. 
Re-activate the Brew Buttons by lifting and lowering the  
Handle completely.
CAUTION: There is extremely hot water in the K-Cup® Pod Holder 
during the brew process. To avoid risk of injury, do not lift the 
Handle or open the K-Cup® Pod Assembly Housing during the 
brew process.
6.  Enjoy your first cup of gourmet   
coffee, tea, or hot cocoa from your 
Keurig® brewer!
5. 
There may be a short pause before the 
brewing process begins. The entire brew 
process lasts for approximately 1 minute 
and ends with a burst of air to remove all 
liquid from the K-Cup® pod  Lift the Handle 
and dispose of the used K-Cup® pod.  
 CAUTION: K-Cup® pod will be hot.
7. The red Heating Light may be illuminated 
as the water is heated for the next brew 
cycle. The brewer will be ready for use in 
approximately 15 seconds. 
NOTE: During this period, your brewer will prepare for the next 
brew. The pump may make a vibrating sound. This is normal.  
						

							1 5 
14
2  |
 TIPS & MAINTENANCE
CONTROLS & INDICATORS (LED CONTROL CENTER) CARING FOR YOUR BREWER
PROGRAMMING AUTO OFF  
TIMER FEATURE
To set the brewer to turn off two hours 
after the last brew follow the steps below. 1. 
Press the Power Button to turn on   
the brewer.
2.  Press the black Auto Off Button to 
turn on the Auto Off Timer feature. 
The green Auto Off Light will illuminate 
When the Auto Off Timer is enabled, 
your brewer will automatically turn off 
two hours after your last brew. 3. 
To disable the Auto Off Timer, simply 
press the black Auto Off Button 
again and the green Auto Off Light 
will turn off.CLEANING EXTERNAL PARTS
CLEANING THE BREWER EXTERIOR
Keep your Keurig
® Classic Series brewer looking its best by 
cleaning the exterior from time to time. Just clean with a damp, 
soapy, lint-free, non-abrasive cloth. Never immerse the brewer in 
water or other liquids.
CLEANING THE DRIP TRAY
The Drip Tray can accumulate up to 8 ounces of overflow. The Drip 
Tray and the Drip Tray Plate should occasionally be rinsed clean. 
To remove the Drip Tray, simply slide it toward you, keeping it level 
at all times to avoid spilling. Clean with a damp, soapy, lint-free, 
non-abrasive cloth.   
						

							1 6 1 7 
2 |
 TIPS & MAINTENANCE
CARING FOR YOUR BREWER
CLEANING THE K-CUP® POD HOLDER ASSEMBLY
Cleaning the Parts The K-Cup® Pod Holder Assembly can be placed 
onto the top shelf of a dishwasher. NOTE: Use low temperature 
cycles in the dishwasher. To remove from the brewer, lift the 
Handle and grasp the top of the K-Cup® Pod Holder with one hand 
while pushing up on the bottom of the K-Cup® Pod Holder from 
underneath with the other until it releases. After cleaning, align the 
K-Cup® Pod Holder with the opening using the two front ribs as a 
guide and snap into place from the top. 
Cleaning the Funnel  The Funnel can be removed from the   
K-Cup® Pod Holder by pulling on it until it pops off. The Funnel   
is dishwasher safe. To replace it, just snap it back onto the   
K-Cup® Pod Holder Assembly.
Cleaning the Exit Needle  The Exit Needle is located on the inside 
bottom of the K-Cup® Pod Holder Assembly. Should a clog arise due 
to coffee grinds, it can be cleaned using a paper clip or similar tool. 
Remove K-Cup® Pod Holder Assembly and detach Funnel. Insert the 
paper clip into the Exit Needle to loosen the clog and push it out. 
The K-Cup® Pod Holder is dishwasher safe. 
CAUTION: There are sharp needles that puncture the K-Cup® pod above the K-Cup® Pod Holder and in 
the bottom of the K-Cup® Pod Holder. To avoid risk of injury, do not put your fingers in the K-Cup® Pod 
Assembly Housing.
CLEANING THE WATER RESERVOIR & WATER RESERVOIR LID
The Water Reservoir Lid and Water Reservoir should be periodically inspected and cleaned.
The Water Reservoir Lid or Water Reservoir should not be put into the dishwasher. They 
should be cleaned with a damp, soapy, non-abrasive cloth and rinsed thoroughly. Do not 
dry the inside of the Water Reservoir with a cloth as lint may remain. 
To clean the filter screen at the base of your Water Reservoir, empty the Water Reservoir 
and follow one or all of the following procedures. 
NOTE: If you are using a water filter inside the Water Reservoir, remove it before cleaning.
1.  Rinse the filter screen with the strong force of water from your faucet. 
2.  If you have a sprayer, aim the water spray at the filter screen. 
3.  Fill the Water Reservoir with approximately two inches of clean water and agitate (shake) 
the Water Reservoir.
Empty the Water Reservoir then fill it with clean water and return it to the brewer.   
If needed, repeat above procedures.
CAUTION: Please rinse the Water Reservoir thoroughly after cleaning. This will ensure that no cleaners or cleaning solutions remain  
in this area as they may contaminate the water supply in the brewer.    
						

							1 8 1 9 
2 |
 TIPS & MAINTENANCE
CARING FOR YOUR BREWER
DESCALING YOUR BREWER
Depending on the mineral content of your water, calcium 
deposits or scale may build up in your brewer. Scale is non- toxic but if left unattended can hinder brewer performance. Regularly descaling your brewer every 3-6 months helps 
maintain the heating element, and other internal parts that 
come in contact with water. Calcium deposits may build up  faster, making it necessary to descale more often. 
You should promptly descale if the red Descale Light is  illuminated. However, even if the red Descale Light is not 
illuminated you should continue to descale your brewer every 
3-6 months. Properly follow the descaling procedure.
DESCALING PROCEDURE
Before you begin, you will need a large ceramic mug, fresh water, descale solution, 
and access to a sink. Do not use a paper cup.
•  Empty the water from the Water Reservoir. If there is a Keurig® Water Filter, 
remove and set aside. Disable “Auto Off ” features, if necessary (refer to page 14). 
STEP 1: FIRST DESCALING SOLUTION RINSE 
•  Press the Power Button to power the brewer off.
•  Pour the entire bottle of Keurig® Descaling Solution into the Water Reservoir.   
Then fill the empty bottle with water and pour into the Water Reservoir. Press   
the Power Button to turn the brewer back on.
•  Place a large mug on the Drip Tray Plate and run a cleansing brew using the 
largest brew size. Do not use a K-Cup® pod. Pour the contents of the mug   
into the sink.  STEP 2: SECOND DESCALING SOLUTION RINSE 
•  Repeat the brew process without a K-Cup® pod, until ADD WATER is 
indicated. Let brewer stand for at least 30 minutes while still on.
•  After 30 minutes, discard any residual solution and rinse the Water 
Reservoir thoroughly.
STEP 3: FRESH WATER RINSE 
•  Ensure the Water Reservoir is filled with fresh water to and not beyond   
the MA X FILL line.
•  Place a large mug on the Drip Tray Plate and run a cleansing brew using the 
largest brew size. Do not use a K-Cup® pod. Pour the contents of the mug 
into the sink.
•  Repeat brew process until you have completed at least 12 brews using the 
largest brew size. You may need to refill the Water Reservoir at least one 
time during this process. 
NOTE: If the red Descale Light is still illuminated after completing the procedure, repeat the descaling procedure above.
NOTE: The cleaning action of Keurig™ Descaling Solution may result in a foam dispensed from the brewer. This is natural, 
as the solution is reacting with the scale inside. For a brewer that is heavily scaled, the brewer may not fill properly 
after the descaler is added. If this occurs, you may see only a small or no output dispensed followed by the sound of air  blowing out. If this occurs:
•  Turn off and unplug the brewer.
•  If there is Keurig® Descaling Solution in the Water Reservoir, discard the 
contents, rinse the Water Reservoir thoroughly and refill with water.
•  Plug the brewer back in, power on, and repeat the Step 3 Fresh Water 
Rinse cycle. The brewer should begin to function normally as the solution is 
rinsed out and the scale is removed. If problem persists, allow brewer to sit  unplugged for at least 30 minutes before continuing with the rinse.
Visit us online for more information at www.Keurig.com/descaling.