Kenwood Rc2000 Mobile Controller Instruction Manual

17
M.IN
Press to enter the Memory Scroll mode {TS-2000
page 60}.  ÒMSRÓ appears on the display.  Turn the
MULTI/ CH control to select your desired memory
channel number.  Press [M.IN] to write the data to
memory.  You can also press [MN.IN] to enter and select
the Memory Name and Memory Group.  Select your
desired character using the MULTI/ CH control, or the
[b]/ [a] and [DEL] keys.  Press [OK] to store the
Memory Name.  Press [G-SEL] to enter the Memory
Group selection.  Select a desired Memory Group...

18
GROUP B KEYS
ÒANT1Ó or ÒANT2Ó appears only when you are operating on the HF ~ 50 MHz band.  ÒANTÓ appears for all other bands
in group BÐ1.  Detailed explanations of each function are provided on the following pages:
n o i t c A] 1 Ð B [] E R P [] T T A [] 1 T N A [] . T . C . P [] L T A S [
: y e k e h t s s e r P2Ð B o t e v o Mr e i f i l p m a - e r P
F F O / N OF F O / N O r o t a u n e t t Ar e h t o n a t c e l e S
a n n e t n ae n u T r e t s u l C t e k c a P
F F O / N Oe d o M e t i l l e t...

19
GROUP BÐ1
PRE
Press to switch the receiver preamplifier ON or OFF
{TS-2000 page 57}.  ÒPREÓ appears on the display when
this function is ON.  ÒP/AÓ appears on the display when
both ÒPREÓ and ÒATTÓ are ON.
AT T
Press to switch the receiver attenuator ON or OFF.
ÒATTÓ appears on the display when this function is ON.
ÒP/AÓ appears on the display when both ÒPREÓ and ÒATTÓ
are ON.
ANT1/ ANT2/ ANT
When operating on the HF ~ 50 MHz band, ÒANT1Ó or
ÒANT2Ó appears.  ÒANTÓ appears when operating on the
144 MHz...

20
GROUP BÐ3
SCAN
Press to start or stop various Scan functions.
AUTO
Press to switch the Auto mode selection function ON or
OFF.  When it is active, ÒAÓ appears on the display.
SG SEL
Press to enter the Scan Group select mode.  Select your
desired memory group numbers using the [b]/ [a] key,
or by turning or pressing the MULTI/ CH control, then
press [SEL] to toggle the selection.  The selected group
numbers are highlighted.  You can also press [ALL]  to
deselect all the group numbers.  Press [OK] to...

21
GROUP C KEYS
The available group C keys change, depending on the current operating mode.  Detailed explanations of each function
are provided on the following pages:
USB/ LSB MODE
GROUP CÐ1
PROC
Press to switch the Speech Processor function ON or
OFF.  ÒPROCÓ appears on the display when it is ON.
Press and hold to configure the Speech Processor
compression level.  While pressing Mic [PTT], speak in
your normal tone and level of voice.  Adjust the input
level using the [c]/ [d] keys or by turning the...

22
T-MON
Press to adjust the monitor level of your transmission
signal.  Adjust the monitor level using the [c]/ [d] keys
or by turning the MULTI/ CH control, then press either
[EXIT] or the MULTI/ CH control to store the setting.
PWR
Press to adjust the output power {TS-2000 page 20}.
Adjust the output power using the [c]/ [d] keys or by
turning the MULTI/ CH control, then press either [EXIT]
or the MULTI/ CH control to store the setting.
GROUP CÐ2
VOX
Press to switch the Voice-Operated Transmission...

23
CW MODE
GROUP CÐ1
CW TUNE
Press to activate the CW Auto Tune function.  Press
[CW TUN] again or [CLR] to exit the function.
CAR
Press to enter the carrier level adjustment mode.  Press
Mic [PTT] to transmit.  Adjust the carrier level within the
ALC zone using the [c]/ [d] keys or by turning the
MULTI/ CH control, then press either [EXIT] or the
MULTI/ CH control to change the setting.
REV
Press to reverse the side-tone pitch.  ÒCWRÓ appears
when it is ON.
PWR
Refer to the USB/ LSB section {page 22}.
n...

24
GROUP CÐ2
VOX
Press to switch the CW break-in function ON or OFF.
BK DLY
Press to adjust the CW break-in delay time {TS-2000
page 42}.  Select your desired break-in delay time using
the [c]/ [d] keys or by turning the MULTI/ CH control,
then press either [EXIT] or the MULTI/ CH control to
change the setting.  The values range from FBK (full
break-in) to 100 which is the slowest delay time.
KEY
Press to adjust the keying speed of the electric keyer.
Select your desired keying speed using the [c]/ [d]...

25
FM MODE
GROUP CÐ1
PROC
Refer to PROC in the USB/ LSB section {page 21}.
ASC
Press to switch the Automatic Simplex function ON/ OFF.
When it is ON, Ò[R]Ó appears.
REV
Press to swap the TX and RX frequency when the
SHIFT function is ON.
T-MON
Refer to T-MON in the USB/ LSB section {page 22}.
PWR
Refer to PWR in the USB/ LSB section {page 22} .
n o i t c A] 1 Ð C [] C O R P [] C S A [] V E R [] N O M - T [] R W P [
y e k e h t s s e r P2Ð C o t e v o Mr o s s e c o r P h c e e p S
F F O / N Ox e l p m i...

26
GROUP CÐ2
VOX
Refer to VOX in the USB/ LSB section {page 22} .
V GAIN
Refer to V GAIN in the USB/ LSB section {page 22}.
V DLY
Refer to V DLY in the USB/ LSB section {page 22}.
NAR
Press to select FM narrow bandwidth operation.  ÒFMNÓ
appears when you operate FM narrow bandwidth.
RF
Refer to RF in the CW section {page 24}.
GROUP CÐ3
CTCSS
Press to activate the CTCSS function.  Press and hold
the key to select your desired CTCSS tone using the
[c]/ [d] keys or by turning the MULTI/ CH control, then...