Kenwood Rc2000 Mobile Controller Instruction Manual

							17
M.IN
Press to enter the Memory Scroll mode {TS-2000
page 60}.  ÒMSRÓ appears on the display.  Turn the
MULTI/ CH control to select your desired memory
channel number.  Press [M.IN] to write the data to
memory.  You can also press [MN.IN] to enter and select
the Memory Name and Memory Group.  Select your
desired character using the MULTI/ CH control, or the
[b]/ [a] and [DEL] keys.  Press [OK] to store the
Memory Name.  Press [G-SEL] to enter the Memory
Group selection.  Select a desired Memory Group using
the MULTI/ CH control or [b]/ [a] keys, then press
[SEL].  Press [OK] to store the new Memory Group
selection.
V/M
Press to select either VFO or Memory Recall mode
{TS-2000 page 59}.  In Memory Recall mode, ÒtMÓ or
ÒMsÓ appears on the display.  Turn the MULTI/ CH
control to select your desired memory channel.
GROUP AÐ5
AÐ5 functions appear only when recalling Memory
Channels 290 ~ 299 {TS-2000 page 62}.
SET
Turn the Tuning control and press [SET] to set the
frequency point of Program Scan Partially Slowed on the
main transceiver {TS-2000 page 67}.  The Ò
Ó icon
appears on the display when you tune to the marked
frequency.  Press and hold the key to clear all the
frequency points that you have configured.
OPEN
Press to confirm the start frequency when you recall a
memory channel from 290 ~ 299 {TS-2000 page 62}.
CLOSE
Press to confirm the end frequency when you recall a
memory channel from 290 ~ 299 {TS-2000 page 62}. 
						

							18
GROUP B KEYS
ÒANT1Ó or ÒANT2Ó appears only when you are operating on the HF ~ 50 MHz band.  ÒANTÓ appears for all other bands
in group BÐ1.  Detailed explanations of each function are provided on the following pages:
n o i t c A] 1 Ð B [] E R P [] T T A [] 1 T N A [] . T . C . P [] L T A S [
: y e k e h t s s e r P2Ð B o t e v o Mr e i f i l p m a - e r P
F F O / N OF F O / N O r o t a u n e t t Ar e h t o n a t c e l e S
a n n e t n ae n u T r e t s u l C t e k c a P
F F O / N Oe d o M e t i l l e t a S
F F O / N O
d n a s s e r P
: y e k e h t d l o h1 Ð C p u o r g o t e v o M ÑÑÑÑÑ
n o i t c A] 2 Ð B [] C E R [] 1 H C [] 2 H C [] 3 H C [
: y e k e h t s s e r P3Ð B o t e v o Mr o f y b - d n a t S
a g n i d r o c e r
e g a s s e mÑ1 H C e h t y a l P
e g a s s e m2 H C e h t y a l P
e g a s s e m3 H C e h t y a l P
e g a s s e m
d n a s s e r P
: y e k e h t d l o h1 Ð C p u o r g o t e v o MÑÑe c i o v a d r o c e R
n i 1 H C n o e g a s s e m
e d o m C E Re c i o v a d r o c e R
n i 2 H C n o e g a s s e m
e d o m C E Re c i o v a d r o c e R
n i 3 H C n o e g a s s e m
e d o m C E R
n o i t c A] 3 Ð B [] N A C S [] O T U A [] L E S G S [] L A U S I V [
: y e k e h t s s e r P4Ð B o t e v o MFF O / N O n a c Sn o i t c n u f e d o m - o t u A
F F O / N On a c S e h t t c e l e S
p u o r GÑn a c S l a u s i V
F F O / N O
d n a s s e r P
: y e k e h t d l o h1 Ð C p u o r g o t e v o M ÑÑÑÑÑ
n o i t c A] 4 Ð B [] L A U D [] L R T C [] K C O L [] M . Q [] R E T E M [
: y e k e h t s s e r P1Ð B o t e v o Mr e v i e c e r - b u S
F F O / N Ol o r t n o C e h t e v o M
r e h t o n a o t d n a b
r e v i e c e ry e K e h t e t a v i t c A
n o i t c n u f k c o lk c i u Q a l l a c e R
l e n n a h c y r o m e Mr e t e m e h t e g n a h C
, C L A , R W S ( e d o m
) y l n o P M O C d n a
g n i t t i m s n a r t e l i h w
d n a s s e r P
: y e k e h t d l o h1 Ð C p u o r g o t e v o MÑÑk c o l y e K e h t t i x E
n o i t c n u fÑr e t e m e h t e l g g o T
r o R W P : e d o m
P M O C / C L A / R W S 
						

							19
GROUP BÐ1
PRE
Press to switch the receiver preamplifier ON or OFF
{TS-2000 page 57}.  ÒPREÓ appears on the display when
this function is ON.  ÒP/AÓ appears on the display when
both ÒPREÓ and ÒATTÓ are ON.
AT T
Press to switch the receiver attenuator ON or OFF.
ÒATTÓ appears on the display when this function is ON.
ÒP/AÓ appears on the display when both ÒPREÓ and ÒATTÓ
are ON.
ANT1/ ANT2/ ANT
When operating on the HF ~ 50 MHz band, ÒANT1Ó or
ÒANT2Ó appears.  ÒANTÓ appears when operating on the
144 MHz ~ 1.2 GHz bands.  Press to select another
antenna when operating on the HF ~ 50 MHz band.
P.C.T.
Press to switch the P.C.T. (Packet Cluster Tune) function
ON or OFF {page 37, TS-2000 page 53}.
SATL
Press to switch the Satellite mode ON or OFF {page 31,
TS-2000 page 53}.
GROUP BÐ2
REC
Press to enter stand-by mode for message recording
{TS-2000 pages 43, 89}.  To start recording a message,
press [CH1], [CH2], or [CH3].
CH1
Press to play back the message which has been
recorded in channel 1.  When [REC] is pressed and the
transceiver is standing by for recording, press this key to
start recording in CH1.
CH2
Press to play back the message which has been
recorded in channel 2.  When [REC] is pressed and the
transceiver is standing by for recording, press this key to
start recording in CH2.
CH3
Press to play back the message which has been
recorded in channel 3.  When [REC] is pressed and the
transceiver is standing by for recording, press this key to
start recording in CH3. 
						

							20
GROUP BÐ3
SCAN
Press to start or stop various Scan functions.
AUTO
Press to switch the Auto mode selection function ON or
OFF.  When it is active, ÒAÓ appears on the display.
SG SEL
Press to enter the Scan Group select mode.  Select your
desired memory group numbers using the [b]/ [a] key,
or by turning or pressing the MULTI/ CH control, then
press [SEL] to toggle the selection.  The selected group
numbers are highlighted.  You can also press [ALL]  to
deselect all the group numbers.  Press [OK] to save the
setting or [CLR] to cancel the selection.
VISUAL
Press to activate the Visual Scan function {page 39,
TS-2000 page 70}.
GROUP BÐ4
DUAL
Press to switch the sub-receiver ON or OFF.
CTRL
Press to move the Control band to another receiver.  The
frequency display of the Control band appears in a large
font.  If the same band is selected for the TX band and
Control band, only ÒPTTÓ appears on the display.
LOCK
Press to lock all the keys and controls of the RC-2000.
Press and hold to unlock the keys and controls of the
RC-2000.
Q.M
Press to recall the Quick Memory channel.  ÒQnnÓ
appears, indicating which Quick Memory channel is
recalled (where ÒnnÓ = 00 ~ 09).  Turn the MULTI/ CH
control to scroll through the Quick Memory channels.
METER
Press to change the meter mode between SWR,  ALC,
and COMP.  Press and hold to toggle the meter mode
between PWR and SWR/ ALC/ COMP. 
						

							21
GROUP C KEYS
The available group C keys change, depending on the current operating mode.  Detailed explanations of each function
are provided on the following pages:
USB/ LSB MODE
GROUP CÐ1
PROC
Press to switch the Speech Processor function ON or
OFF.  ÒPROCÓ appears on the display when it is ON.
Press and hold to configure the Speech Processor
compression level.  While pressing Mic [PTT], speak in
your normal tone and level of voice.  Adjust the input
level using the [c]/ [d] keys or by turning the
MULTI/ CH control, then press either [EXIT] or the
MULTI/ CH control to accept the new setting.
MIC
Press to enter the Mic Gain adjustment mode.  While
pressing Mic [PTT], speak in your normal tone and level
of voice.  Adjust the microphone gain using the [c]/ [d]
keys or by turning the MULTI/ CH control, then press
either [EXIT] or the MULTI/ CH control to store the
setting.  While the Speech Processor function is ON, it
works as the Speech Processor output level adjustment
control.
n o i t c A] 1 Ð C [] C O R P [] C I M [] N O M - T [] R W P [
: y e k e h t s s e r P2Ð C o t e v o Mr o s s e c o r P h c e e p S
F F O / N OÑtn e m t s u j d a n i a g C I Ml e v e l r o t i n o M X T
t n e m t s u j d ar e w o p t u p t u O
t n e m t s u j d a
d n a s s e r P
: y e k e h t d l o h1 Ð A p u o r g o t e v o Mr o s s e c o r P h c e e p S
l e v e l t u p n i
t n e m t s u j d aÑÑÑÑ
n o i t c A] 2 Ð C [] X O V [] N I A G V [] Y L D V [] F R [
: y e k e h t s s e r P3Ð C o t e v o MFF O / N O X O Vn i a g X O V
t n e m t s u j d ay a l e d X O V
t n e m t s u j d aÑtn e m t s u j d a n i a g F R
d n a s s e r P
: y e k e h t d l o h1 Ð A p u o r g o t e v o M ÑÑÑÑÑ
n o i t c A] 3 Ð C [] . R . N [] . N . A [] . C . B [] . C . B . M [] R E T L I F [
: y e k e h t s s e r P1Ð C o t e v o M1 n o i t c u d e R e s i o N
F F O / N O 2 r oh c t o N o t u A
F F O / N Ol e c n a C t a e B
F F O / N Ol e c n a C t a e B l a u n a M
F F O / N Or e t l i f P S D e r u g i f n o C
g n i t t e s
d n a s s e r P
: y e k e h t d l o h1 Ð A p u o r g o t e v o Me s i o N e h t t s u j d A
r e t e m a r a p n o i t c u d e Rl e v e l h c t o N o t u A
t n e m t s u j d aÑt a e B l a u n a M t s u j d A
y c n e u q e r f l e c n a CÑ 
						

							22
T-MON
Press to adjust the monitor level of your transmission
signal.  Adjust the monitor level using the [c]/ [d] keys
or by turning the MULTI/ CH control, then press either
[EXIT] or the MULTI/ CH control to store the setting.
PWR
Press to adjust the output power {TS-2000 page 20}.
Adjust the output power using the [c]/ [d] keys or by
turning the MULTI/ CH control, then press either [EXIT]
or the MULTI/ CH control to store the setting.
GROUP CÐ2
VOX
Press to switch the Voice-Operated Transmission
function ON or OFF {TS-2000 page 39}.
V GAIN
Press to adjust the VOX gain {TS-2000 page 39}.  While
pressing Mic [PTT], adjust the VOX gain using the [c]/
[d] keys or by turning the MULTI/ CH control, then
press either [EXIT] or the MULTI/ CH control to store the
setting.
V DLY
Press to adjust the VOX delay time.  Select your desired
delay time using the [c]/ [d] keys or by turning the
MULTI/ CH control, then press either [EXIT] or the
MULTI/ CH control to change the setting.
RF
Refer to RF in the CW section {page 24}.
GROUP CÐ3
N.R.
Press to activate Noise Reduction 1, Noise Reduction 2,
or to turn the function OFF.  When the noise reduction
function is ON, ÒN.R.1Ó or ÒN.R.2Ó appears above the
key.  When it is ON, press and hold the key to change
the noise reduction level.  Adjust the noise reduction
level using the [c]/ [d] keys or by turning the
MULTI/ CH control, then press either [EXIT] or the
MULTI/ CH control to store the setting.
A.N.
Press to switch the Auto Notch function ON or OFF.
Press and hold the key to change the Auto Notch level.
Adjust the Auto Notch tracking time constant using the
[c]/ [d] keys or by turning the MULTI/ CH control, then
press either [EXIT] or the MULTI/ CH control to store the
setting.
B.C.
Press to switch the automatic Beat Cancel function ON
or OFF.  ÒB.C.Ó and ÒDSPÓ appear when it is ON.
M.B.C.
Refer to M.B.C. in the CW section {page 24}.
FILTER
Refer to FILTER in the CW section {page 24}. 
						

							23
CW MODE
GROUP CÐ1
CW TUNE
Press to activate the CW Auto Tune function.  Press
[CW TUN] again or [CLR] to exit the function.
CAR
Press to enter the carrier level adjustment mode.  Press
Mic [PTT] to transmit.  Adjust the carrier level within the
ALC zone using the [c]/ [d] keys or by turning the
MULTI/ CH control, then press either [EXIT] or the
MULTI/ CH control to change the setting.
REV
Press to reverse the side-tone pitch.  ÒCWRÓ appears
when it is ON.
PWR
Refer to the USB/ LSB section {page 22}.
n o i t c A] 1 Ð C [] N U T W C [] R A C [] V E R [] R W P [
: y e k e h t s s e r P2Ð C o t e v o Mn o i t c n u f e n u T W C
F F O / N Ol e v e l r e i r r a c a t s u j d A- e d i s e h t e s r e v e R
y c n e u q e r f h c t i p e n o tÑr e w o p t u p t u O
t n e m t s u j d a
d n a s s e r P
: y e k e h t d l o h1 Ð A p u o r g o t e v o Mn o i t c n u f e n u T W C
F F O / N OÑÑÑÑ
n o i t c A] 2 Ð C [] X O V [] Y L D K B [] Y E K [] F R [
: y e k e h t s s e r P3Ð C o t e v o MFF O / N O n i - k a e r BÑn i - k a e r B e h t t s u j d A
e m i t y a l e dc i r t c e l e e h t t s u j d A
d e e p s r e y e kt n e m t s u j d a n i a g F R
d n a s s e r P
: y e k e h t d l o h1 Ð A p u o r g o t e v o M ÑÑÑÑÑ
n o i t c A] 3 Ð C [] . R . N [] . C . B . M [] R E T L I F [
: y e k e h t s s e r P1Ð C o t e v o M1 n o i t c u d e R e s i o N
F F O / N O 2 r oÑÑl e c n a C t a e B l a u n a M
F F O / N Or e t l i f P S D e r u g i f n o C
g n i t t e s
d n a s s e r P
: y e k e h t d l o h1 Ð A p u o r g o t e v o Me s i o N e h t t s u j d A
r e t e m a r a p n i o t c u d e RÑÑt a e B l a u n a M t s u j d A
y c n e u q e r f l e c n a CÑ 
						

							24
GROUP CÐ2
VOX
Press to switch the CW break-in function ON or OFF.
BK DLY
Press to adjust the CW break-in delay time {TS-2000
page 42}.  Select your desired break-in delay time using
the [c]/ [d] keys or by turning the MULTI/ CH control,
then press either [EXIT] or the MULTI/ CH control to
change the setting.  The values range from FBK (full
break-in) to 100 which is the slowest delay time.
KEY
Press to adjust the keying speed of the electric keyer.
Select your desired keying speed using the [c]/ [d]
keys or by turning the MULTI/ CH control, then press
either [EXIT] or MULTI/ CH control to change the setting.
The adjustable  keying speed is between 10 (WPM) and
60 (WPM).
RF
Press to adjust the Radio Frequency (RF) gain for the
main transceiver.  Select your desired RF gain value
using the [c]/ [d] keys or by turning the MULTI/ CH
control, then press either [EXIT] or the MULTI/ CH
control to change the setting.  The minimum RF gain
value is 0 and the maximum value is 255.
GROUP CÐ3
N.R.
Refer to N.R. in the USB/ LSB section {page 22}.
M.B.C.
Press to switch the Manual Beat Cancel function ON or
OFF.  Press and hold the key to enter the manual beat
cancel frequency adjustment mode.  Adjust the beat
cancel frequency using the [c]/ [d] keys or by turning
the MULTI/ CH control, then press either [EXIT] or the
MULTI/ CH control to store the setting.
FILTER
USB/ LSB/ FM/ AM mode:
Press to adjust the low cut-off or high cut-off frequency
of the DSP.  Press [HI] or [LOW] to select the high or
low cut-off, then press [
c cc c
c]/ [
d dd d
d] or turn the MULTI/ CH
control to select the desired cut-off frequency.  Press
[EXIT] or MULTI/ CH control to accept the new setting.
CW/ FSK mode:
Press to adjust the DSP filter width or shift frequency.
Press [SFT] to adjust the shift frequency, then press
[
c cc c
c]/ [
d dd d
d] or turn the MULTI/ CH control to select the
desired shift  frequency.  Press [EXIT] to accept the new
setting.  Press [WID] to adjust the filter width, then press
[
c cc c
c]/ [
d dd d
d] or turn the MULTI/ CH control to select the
desired shift  frequency.  Press [EXIT] or MULTI/ CH
control to accept the new setting. 
						

							25
FM MODE
GROUP CÐ1
PROC
Refer to PROC in the USB/ LSB section {page 21}.
ASC
Press to switch the Automatic Simplex function ON/ OFF.
When it is ON, Ò[R]Ó appears.
REV
Press to swap the TX and RX frequency when the
SHIFT function is ON.
T-MON
Refer to T-MON in the USB/ LSB section {page 22}.
PWR
Refer to PWR in the USB/ LSB section {page 22} .
n o i t c A] 1 Ð C [] C O R P [] C S A [] V E R [] N O M - T [] R W P [
y e k e h t s s e r P2Ð C o t e v o Mr o s s e c o r P h c e e p S
F F O / N Ox e l p m i S c i t a m o t u A
F F O / N O k c e h Ce s r e v e r t f i h S
F F O / N Ol e v e l r o t i n o M X T
t n e m t s u j d ar e w o p t u p t u O
t n e m t s u j d a
d n a s s e r P
y e k e h t d l o h1 Ð A p u o r g o t e v o Mr o s s e c o r P h c e e p S
l e v e l t u p n i
t n e m t s u j d aÑÑÑÑ
n o i t c A] 2 Ð C [] X O V [] N I A G V [] Y L D V [] R A N [] F R [
y e k e h t s s e r P3Ð C o t e v o MFF O / N O X O Vn i a g X O V
t n e m t s u j d ay a l e d X O V
t n e m t s u j d ah t d i w d n a b w o r r a N
F F O / N Ot n e m t s u j d a n i a g F R
d n a s s e r P
y e k e h t d l o h1 Ð A p u o r g o t e v o M ÑÑÑÑÑ
n o i t c A] 3 Ð C [] S S C T C [] E N O T [] S C D [] T L A [] T F I H S [
y e k e h t s s e r P4Ð C o t e v o MFF O / N O S S C T CFF O / N O E N O TFF O / N O S C DFF O / N O T L Ae h t t c e l e S
n o i t c e r i d T F I H S
d n a s s e r P
y e k e h t d l o h1 Ð A p u o r g o t e v o Men o t S S C T C t c e l e Sz H 0 5 7 1 t i m s n a r T
e n o te d o c S C D t c e l e SÑt e s f f o e h t t s u j d A
y c n e u q e r f
n o i t c A] 4 Ð C [] . R . N [] L E S . T [] . C . B . M [] R E T L I F [
y e k e h t s s e r P1Ð C o t e v o M1 n o i t c u d e R e s i o N
F F O / N Oe n o t - b u s a t c e l e S
y c n e u q e r fÑl e c n a C t a e B l a u n a M
F F O / N Or e t l i f P S D e r u g i f n o C
s g n i t t e s
d n a s s e r P
y e k e h t d l o h1 Ð A p u o r g o t e v o Me s i o N e h t e r u g i f n o C
r e t e m a r a p n o i t c u d e RÑÑt a e B l a u n a M t s u j d A
y c n e u q e r f l e c n a CÑ 
						

							26
GROUP CÐ2
VOX
Refer to VOX in the USB/ LSB section {page 22} .
V GAIN
Refer to V GAIN in the USB/ LSB section {page 22}.
V DLY
Refer to V DLY in the USB/ LSB section {page 22}.
NAR
Press to select FM narrow bandwidth operation.  ÒFMNÓ
appears when you operate FM narrow bandwidth.
RF
Refer to RF in the CW section {page 24}.
GROUP CÐ3
CTCSS
Press to activate the CTCSS function.  Press and hold
the key to select your desired CTCSS tone using the
[c]/ [d] keys or by turning the MULTI/ CH control, then
press either [EXIT] or the MULTI/ CH control to change
the setting.  Press [SCAN] to start the CTCSS Freq. ID
Scan.
TONE
Press to activate the TONE function.
DCS
Press to activate the DCS function.  Press and hold the
key to select your desired DCS code using the [c]/ [d]
keys or by turning the MULTI/ CH control, then press
either [EXIT] or the MULTI/ CH control to change the
setting.  Press [SCAN] to start the DCS code ID Scan.
ALT
Press to activate the Auto Lock Tuning (ALT) function
(1.2 GHz band only).  When it is ON, Ò
Ó appears.
SHIFT
Press to select the desired repeater shift direction. ÒÐÓ,
Ò+Ó, or Ò=Ó appears to indicate the shift direction.
GROUP CÐ4
N.R.
Refer to N.R. in the USB/ LSB section {page 22}.
T.SEL
Press to select your desired TONE frequency using the
[c]/ [d] keys or by turning the MULTI/ CH control, then
press either [EXIT] or the MULTI/ CH control to change
the setting.  Press [SCAN] to start the TONE ID Scan.
M.B.C.
Refer to M.B.C. in the CW section {page 24}.
FILTER
Refer to FILTER in the CW section {page 24}.