JVC Th V70r Instructions

							28
2 Insert a disc into the disc slot with the label side facing the front or up as shown below.
Insert a disc halfway, then it is pulled into the center unit automatically.
L
R
L
LFE
LS
RS CR
SURROUNDDIGITAL
Current chapter number Playing back a DVD:
(EX. When a DVD encoded with
Dolby Digital 5.1ch is played)
Time information
Signal indicators (see page 34.)
Current surround mode and digital signal format (see page 33.)
Playing back a VCD/SVCD/
Audio CD:
(EX. When a VCD is played)
Current track numberCurrent disc type
Playback information on the display window
While loading and playing a disc, the current title/chapter/track numbers, time, and status information appear on the display
window.
NOTES:
•You can change the time information mode. See page 38.
•You can also check the playback information on the TV screen. See page 37.
•The current disc type information appears as follows:
– “VCD”: shows a VCD or SVCD is loaded.
– “CD”: shows an Audio CD is loaded.
•When a Video CD or SVCD with PBC function is played, the time information does not appear, but “PBC” appears.
Time information
DVDAUDIO
CD
SUPER
VCD
VIDEO
CD
Stopping playback temporarily
From the remote control:Press PAUSE.
On the center unit:Press 8.
To return to normal playback,
Press PLAY (or 3 on the center unit).
When the center unit is placed horizontally, the moving panel
closes after inserting the disc.
After the system reads the disc information, playback starts.
To remove a disc
Press 0 again. The disc comes out from the disc slot. “EJECT” appears on the display window and on the TV screen.
NOTE: When the center unit is placed vertically
When AM, FM, AUX, or AUX DIGITAL is selected as the source, if the indication as illustrated below appears on the
display window, a disc is already inserted. Press 0 to remove the disc before inserting another disc.
Example: When “AUX” is selected.
NOTES:
•With Video CDs/SVCDs with PBC function (see page 7), or some DVD Video discs, the menu display may appear on the TV screen after
starting playback. In such a case, select an item to be played back from the menu. See page 39.
•When the system is in standby mode, pressing 
0 also turns on the system.
•The stored position for the resume playback is canceled when removing a disc.
•You can check the playback information on the display window and the TV screen (see page 37).
DVD DIGITAL THEATER SYSTEMTH-V70
•When the center unit is placed vertically•When the center unit is placed horizontally
Label sideDisc slot
Disc slot
Label side
L
R
This indication shows
that a disc is inserted.
EN21-30TH-V70[J]B02.3.13, 9:16 PM 28
 
						

							29
Basic playback
CHANNEL VOLUME
TV  VOL
TUNINGS TOP
DIMMER P
A USE
FF//REW
TV/VIDEO1MUTING¡
REC PL
AYD O WN   UP
MEMO RY 
STROBE
CONT ROL  – SUB WOOFER + EFFECT
–     CENTER     +
–  
    REAR-R       +
TEST
SLEEP TV
VCR
SETTING
TV RETURN
ENTER
ON
SCREEN
CHOICE
A UDIO/
TV/VCR
SUR ROUNDMODE
FM MODE
1 2
3
4   56
7   8
 
9
10 0 +10100+
C ATV/DBS
–      REAR-L     +
Number
b uttons
1 / ¡
b uttons
FF/  ¢  b utton
\f /REW
b utton
SOURCE   VOL
7 b utton
\f  b utton
¢
 b utton
DVDAUDIO
CD
SUPER
VCD
VIDEO
CD
Stopping pl ayba ck complete ly
From the remote control:  Press STOP.
On the center unit:  Press 7.
7 When the resume pl ayba ck is set to  “ ON ” (see p ag e 62):
Once you p ress the button, playback stops and the position whe re playback has been stopped is sto red. (The RESUME
indicator lights up.)
T o clear the sto red position, p ress STOP (or  7  on the center unit) again.
7  Sta rting pl ayba ck  again
From the remote control:  Press PLAY.
On the center unit:  Press 3.
7 When the resume pl ayba ck is set to  “ ON ” (see p ag e 62):
When the system sto red the position whe re playback has been stopped, playback sta rts f rom the sto red position (the  resume
playback). (The RESUME indicator goes o ff.)
When the sto red position has been clea red, playback sta rts f rom the beginning of the disc.
N O TE:
The resume pl ayba ck do es not wo rk  for  Audio CD s.
Moving back the playback position during DVD playback
During playback of a DVD, you can move back the playback position by 10 \
seconds from the current position.
From the remote control:Press PLAY during playback of DVD.
On the center unit:Press  3 during playback of DVD.
The playback position moves back by 10 seconds from the current position.
NO TES:
• This function w orks betw een chapters in the same title .
• This function ma y not work  f or some D VDs.
3 button
PLAY button
STOP button
DVD
EN21-30TH-V70[J]B 02.3.13, 9:16 PM
29
 
						

							30
Searching for a particular point
You can search for a particular point while playing a disc.
7Method 1 (from the remote control ONLY):
To fast-forward playback, press ¡ during playback.
Each time you press the button, the search speed changes as follows.
] 
x2 ] x5 ] x10] x20] x60*
To fast-reverse playback, press 1during playback.
Each time you press the button, the search speed changes as follows.
] 
x2 ] x5 ] x10] x20] x60*
To return to the normal speed playback
Press PLAY (or 3 on the center unit).
7Method 2:
Press and hold FF/¢ or 4/REW (or ¢ or 4 on the center unit).
Continuously pressing ¢ or 4 increases the fast-forward/reverse playback speed as follows:
x5 ] x20
To return to the normal speed playback, release the button.
NOTES:
•When a DVD, Video CD, or SVCD is played back, no sound comes out during fast-forward/reverse playback.
•This function may not work for some DVDs.
Locating the beginning of a desired chapter or track
You can locate the beginning of a chapter (for DVD Video) or track (for Video CD/Audio CD) by
pressing ¢ or 4.
7For DVD: During playback
For Video CD/SVCD: During playback without PBC function
For Audio CD: During playback or while stopped
Press FF/¢ or 4/REW (or ¢ or 4 on the center unit).
• To skip chapters or tracks forward, press ¢as many times as required.
• To skip to the beginning of the current chapter or track, press 4once.
• To skip chapters or tracks backward, press  4as many times as required.
NOTES:
•This function may not work for some DVDs.
•While playing a VCD or SVCD with the PBC function, 
¢ and 4 may be used for the operations of menu-driven playback (see pages 7 and 39).
Locating a desired selection using Number buttons
You can locate the desired title, chapter (for DVD Video) or track (for Video CD/SVCD/Audio CD)
by selecting its number.
7For DVD: While stopped (the title number is selected.)
During playback (the chapter number is selected.)
For Audio CD: During playback or while stopped
For Video CD/SVCD: During playback without PBC function
From the remote control ONLY:
Press Number buttons (1-10, +10) to select the desired title, chapter, or track number.
• To select 3, press 3.
• To select 14, press +10 then 4.
• To select 24, press +10, +10, then 4.
• To select 40, press +10, +10, +10 then 10.
The specified title, chapter, or track number appears on the display window, and playback begins from that location.
NOTES:
•While playing a DVD, if a menu is shown on the TV screen, Number buttons may be used for selecting an item in the menu (see page 39).
•While playing a VCD or SVCD with the PBC function, if a menu is shown on the TV screen, Number buttons are used for selecting an item in
the menu (see page 39).
DVDAUDIO
CD
SUPER
VCD
VIDEO
CD
DVDAUDIO
CD
SUPER
VCD
VIDEO
CD
DVDAUDIO
CD
SUPER
VCD
VIDEO
CD
*x60and x60 are
available to DVD only.
EN21-30TH-V70[J]B02.3.13, 9:16 PM 30
 
						

							31
Tuner operations
IMPORTANT:
When using the remote control, check to see if
its remote control mode selector is set to the
correct position:
To operate this system, set it to “AUDIO/TV/
VCR.”
Tuning in to stations manually
From the remote control ONLY:
1 Press FM/AM repeatedly to select the band.
Each time you press the button, the band alternates
between FM and AM.
The selected band appears on the display window, then
the last received staion appears.
Example: When AM is selected
2 Press TUNING UP (FF/¢) or DOWN (4/
REW) repeatedly until you find the frequency
you want.
• TUNING UP (FF/¢):Increases the frequency.
• TUNING DOWN (4/REW):Decreases the frequency.
When you hold down the button and then release it, the
system starts searching for stations and stops when a
station of sufficient signal strength is tuned in to.
AUDIO/
TV/VCR
CATV/DBS
You can browse through all the stations or use the preset function to go immediately to a particular station.
¥ Before operating the tuner from the remote control, press FM/AM to use the remote control for the tuner operations.
NOTES:
• When a station of sufficient signal strength is tuned in, the TUNED
indicator lights up on the display window.
• When an FM stereo program is received, the STEREO indicator
lights up.
Using preset tuning
Once a station is assigned to a channel number, the station
can be quickly tuned in. You can preset 30 FM and 15 AM
stations.
7To store the preset stations
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
cancelled before you finish, star t from step 2 again.
From the remote control ONLY:
1 Tune in the station you want to preset (see
“Tuning in to stations manually”).
• If you want to store the FM reception mode for an FM
station, select the reception mode you want. See
“Selecting the FM reception mode” on page 32.
ATT
L
CRMPEG–2
RESUMETUNED
STEREO AUTO MUTINGRDS TANEWS INFOATTRESUMETUNED
STEREO AUTO MUTINGRDS TANEWS INFO
ATT
L
CRMPEG–2
RESUMETUNED
STEREO AUTO MUTINGRDS TANEWS INFOATTRESUMETUNED
STEREO AUTO MUTINGRDS TANEWS INFO
CHANNEL VOLUME TV VOL
TUNINGFF//REW
TV/VIDEO1MUTING¡
PLAYDOWN UP
DV DVCR 1
AUDIOAUX
ANGLEFM/AM
SUBTITLEDECODE
RETURN DIGEST ZOOM VFP
TOP MENU MENU ZOOM
CONTROL– SUBWOOFER +EFFECT
–     CENTER     +
– 
    REAR-R     +
TEST
SLEEPTV VCR
SETTING
TV RETURN
ENTER
ON
SCREEN
CHOICE
AUDIO/
TV/VCR
SURROUNDMODE
FM MODE
12 3
45 6
78 9
100+10100+
CATV/DBS
VCR
SOUND– +
–     REAR-L     +
PROGRESSIVE
FM/AM button
TUNING DOWN
(4/REW)
buttonTUNING UP
(FF/¢)
button
CHANNEL VOLUME TV VOL
TUNINGSTOPPAUSE
FF//REW
TV/VIDEO1MUTING¡
RECPLAYDOWN UP
MEMORY
STROBE
DV DVCR 1
AUDIOAUX
ANGLEFM/AM
SUBTITLEDECODE
RETURN DIGEST ZOOM VFP
TOP MENU MENU ZOOM
CONTROL– SUBWOOFER +EFFECT
–     CENTER     +
– 
    REAR-R     +
TEST
SLEEPTV VCR
SETTING
TV RETURN
ENTER
ON
SCREEN
CHOICE
AUDIO/
TV/VCR
SURROUNDMODE
FM MODE
12 3
45 6
78 9
100+10100+
CATV/DBS
VCR
SOUND– +
–     REAR-L     +
PROGRESSIVE
FM/AM button
MEMORY
(
•REC) buttonNumber
buttons
ATT
L
CRMPEG–2
RESUMETUNED
STEREO AUTO MUTINGRDS TANEWS INFOATTRESUMETUNED
STEREO AUTO MUTINGRDS TANEWS INFO
EN31-32TH-V70[J]B02.3.13, 9:13 PM 31
 
						

							32
2 Press MEMORY (•REC).
The channel number position starts flashing on the
display window for about 5 seconds.
3 Press Number button(s) (1-10, +10) to select a
channel number while the channel number
position is flashing.
The channel number and the CH indicator start flashing.
Examples:
• For channel number 3, press 3.
• For channel number 14, press +10 then 4.
(For FM stations only)
• For channel number 24, press +10, +10, then 4.
• For channel number 30, press +10, +10, then 10.
4 Press MEMORY (•REC) again while the
selected number is flashing on the display
window.
The selected number stops flashing.
The station is assigned to the selected preset number.
5 Repeat steps 1 to 4 until you store all the
stations you want.
To erase a stored preset station
Storing a new station on a used number erases the previously
stored one.
7To tune in to a preset station
From the remote control ONLY:
1 Press FM/AM repeatedly to select the band.
Each time you press the button, the band alternates
between FM and AM.
2 Press Number button(s) (1-10, +10) to select a
preset channel number.
Examples:
• For channel number 3, press 3.
• For channel number 14, press +10 then 4.
(For FM stations only)
• For channel number 24, press +10, +10, then 4.
• For channel number 30, press +10, +10, then 10.
Selecting the FM reception
mode
When a stereo FM program tuned in currently is noisy, you
can change the FM reception mode to improve the reception.
• You can store the FM reception mode for each preset
station. See “Using preset tuning” on page 31.
From the remote control ONLY:
Press FM MODE (0) while listening to an FM
station.
The FM reception mode appears on the display window.
Each time you press the button, the FM reception mode
alternates between “AUTO MUTING” and “MONO.”
•AUTO MUTING:
When a program is broadcasted in stereo, you will hear
stereo sounds. (The STEREO indicator lights up on the
display window.) When in monaural, you will hear monaural
sounds. This mode is also useful to suppress static noise
between stations. The AUTO MUTING indicator lights up on
the display window.
•MONO:
Reception will be improved although you will lose the
stereo effect. (The STEREO indicator goes off.) In this
mode, you will hear noise untill you are tuned in to a station.
(The AUTO MUTING indicator also goes off.)
Reducing the noise of AM
broadcast
When listening to an AM broadcast with a lot of noise
interference, you can change the Beat Cut mode to reduce
the noise.
From the remote control ONLY:
Press FM MODE (0) while listening to an AM
station.
The current BEAT CUT mode appears on the display window.
Each time you press the button, the Beat Cut mode alternates
between “BEAT CUT 1” and “BEAT CUT 2.”
• Choose “BEAT CUT 1” or “BEAT CUT 2” that will give
clearer sound.
ATT
L
LFE
LS
SRS CRMPEG–2AAC
DSP
RESUMETUNED
STEREO AUTO MUTING
RDS TANEWS INFOATTRESUMETUNED
STEREO AUTO MUTINGRDS TANEWS INFO
ATT
L
LFECRMPEG–2AAC
CH
RESUMETUNED
STEREO AUTO MUTING
RDS TANEWS INFOATTRESUMETUNED
STEREO AUTO MUTINGRDS TANEWS INFO
CONTROL– SUBWOOFER +EFFECT
–     CENTER     +
– 
    REAR-R     +
TEST
SLEEPTV VCR
SETTING
TV RETURN
ON
SCREENAUDIO/
TV/VCR
FM MODE
123
45 6
78 9
100+10100+
–     REAR-L     +
CONTROL– SUBWOOFER +EFFECT
–     CENTER     +
– 
    REAR-R     +
TEST
SLEEPTV VCR
SETTING
TV RETURN
ON
SCREENAUDIO/
TV/VCR
FM MODE
123
45 6
78 9
100+10100+
–     REAR-L     +
FM MODE (0)
button
FM MODE (0)
button
EN31-32TH-V70[J]B02.3.13, 9:13 PM 32
 
						

							33
Creating the realistic sound fields
7Dolby Surround
• Dolby Pro Logic II
• Dolby Digital
7DTS Digital Surround
7DAP modes
7All Channel Stereo
7 Dolby Surround
Dolby Pro Logic II*
Dolby Pro Logic II has newly developed multichannel
playback format to decode all 2 channel sources—stereo
source and Dolby Surround encoded source—into 5.1
channel.
Matrix-based encoding/decoding method for Dolby Pro Logic II
makes no limitation for the cutoff frequency of the rear treble and
enables stereo rear sound compared to conventional Dolby Pro
Logic.
Dolby Pro Logic II enables to reproduce spacious sound from
original sound without adding any new sounds and tonal
colorations.
Dolby Pro Logic II has two modes—Movie mode and Music
mode:
Pro Logic II Movie (PL II MOVIE)—suitable for reproduction of
Dolby Surround  encoded sources bearing the mark
DOLBY SURROUND. You can enjoy soundfield very close to the one
created with discrete 5.1 channel sounds.
Pro Logic II Music (PL II MUSIC)—suitable for reproduction of
any 2 channel stereo music sources. You can enjoy wide and deep
sound by using this mode.
• When Dolby Pro Logic II is activated, the 
PRO LOGIC II
indicator lights up on the display window.
** Manufactured under license from Digital Theater Systems, Inc. US
Pat. No. 5,451,942 and other world-wide patents issued and
pending. “DTS” and “DTS Digital Surround” are trademarks of
Digital Theater Systems, Inc. Copyright 1996 Digital Theater
Systems, Inc. All rights reserved. * Manufactured under license from Dolby Laboratories. “Dolby,” “Pro
Logic,” and the double-D symbol are trademarks of Dolby
Laboratories.
Typical Multichannel (5.1 ch) reproduction
  Right rear 
speaker
Left front 
speaker
Subwoofer
Left rear 
speaker
Right front 
speaker
DVD DIGITAL THEATER SYSTEMTH-V70
Center 
speaker
You can use the following Surround modes to reproduce a realistic sound field.
Dolby Digital*
Used to reproduce multichannel soundtracks of the software
encoded with Dolby Digital (
).
Dolby Digital 5.1 ch (DOLBY D) encoding method (so-called
discrete multichannel digital audio format) records and
digitally compresses the left front channel, right front channel,
center channel, left rear channel, right rear channel, and LFE
channel signals.
Since each channel is completely independent from the other
channel signals to avoid interference, you can obtain much
better sound quality with much stereo and surround effects.
NOTE:
Dolby Digital software can be roughly grouped into two categories—
multichannel (up to “5.1” channel) and 2 channel software. To enjoy
surround sounds while playing Dolby Digital 2 ch software, you can
use Dolby Pro Logic II.
7 DTS Digital Surround**
Used to reproduce multichannel soundtracks of the software
encoded with DTS Digital Surround (
).
DTS Digital Surround (DTS SURR) is another discrete
multichannel digital audio format available on CD, LD, and
DVD software.
Compared to Dolby Digital, audio compression ratio is
relatively low. This fact allows DTS Digital Surround format to
add breadth and depth to the reproduced sounds. As a
result, DTS Digital Surround features natural, solid and clear
sound.
7 Digital signal format indicators on the display
window
DIGITAL: Lights up when Dolby Digital signals
come in.
: Lights up when DTS Digital (Surround)
signals come in.
No indication: No digital signal indicator lights up when
Linear PCM signals or analog signals
come in.
EN33-36TH-V70[J]B02.3.13, 9:14 PM 33
 
						

							34
7 DAP (Digital Acoustic Processor) modes
DAP modes have been designed to create important
acoustic surround elements.
The sound heard in a live club, dance club, hall or pavilion
consists of direct sound and indirect sound—early reflections
and reflections from behind. Direct sounds reach the listener
directly without any reflection. On the other hand, indirect
sounds are delayed by the distances of the ceiling and walls
(see the diagram below).
These indirect sounds are important elements of the acoustic
surround effects. The DAP mode can reproduce a realistic
sound field by adding these indirect sounds.
The following DAP modes are provided with this system.
LIVE CLUB:Gives the feeling of a live music club with a
low ceiling.
DANCE CLUB:Gives a throbbing bass beat.
HALL:Gives clear vocal and the feeling of a
concert hall.
PAVILION:Gives the spacious feeling of a pavilion with
a high ceiling.
These DAP modes can be used to add the acoustic surround
effects while reproducing 2 channel stereo software, either
analog or Linear PCM, and can give you a real “being there”
feeling.
• When one of the DAP modes is selected, the DSP indicator
lights up on the display window.
Creating sound field
Reflections from behind
Early reflections
Direct sounds
7 All Channel Stereo
All Channel Stereo (ALL CH ST.) mode can reproduce a
larger stereo sound field using all the connected (and
activated) speakers.
All Channel Stereo can be used while reproducing 2 channel
stereo software, either analog or Linear PCM.
• When All Channel Stereo is selected, the DSP indicator
lights up on the display.
All Channel Stereo reproduction
Normal stereo sound
All channel stereo
Available Surround modes for each input signal‡: Possible / ×: Impossible
             Mode SURROUND DOLBY DTS PLII PLII LIVE DANCE HALL PAVILION ALL CH
Signals OFF (stereo) DIGITAL SURROUND MOVIE MUSIC CLUB CLUB ST.
Dolby Digital
‡‡
× × ××× × × ×(Multichannel)
Dolby Digital
‡×ׇ‡×× × × ×(2 channel)
DTS Digital
Surround‡
×‡× ××× × × ×
(Multichannel)
DTS Digital
Surround‡
×ׇ‡×× × × ×
(2 channel)
Analog
(AUX/FM/AM)
‡
×ׇ ‡‡‡ ‡ ‡ ‡
or
Linear PCM
L
LFE
LS
SRS CR
7 The signal indicators on the display window
Light up to indicate the incoming signals.
L:Lights up when the left channel signal comes in.
C:Lights up when the center channel signal comes in.
R:Lights up when the right channel signal comes in.
LFE:Lights up when the LFE channel signal comes in.
LS:Lights up when the left surround channel signal
comes in.
RS:Lights up when the right surround channel signal
comes in.
S:Lights up when the monaural rear channel signal or 2
channel Dolby Surround signal comes in.
EN33-36TH-V70[J]B02.3.13, 9:14 PM 34
 
						

							35
Creating the realistic sound fields
Selecting the surround mode
The system is so set up in its initial state that it automatically
selects the optimal surround mode for each input signal
(AUTO SURROUND MODE).
Only when you want to change a surround mode selected
automatically, perform the following procedure.
• After having changed the surround mode, turning off the
power or changing sources resumes the auto surround
mode.
From the remote control ONLY
Press SURROUND MODE.
The current surround mode is called up and appears on the
display window.
Each time you press the button, the surround mode changes
as follows.
] PL II MOVIE ] PL II MUSIC ] LIVE CLUB
] DANCE CLUB ] HALL ] PAVILION
] ALL CH ST.] STEREO (surround off)
] (back to the beginning)
NOTES:
•When you have set the rear speakers to “NONE,” you cannot use
the DAP modes and All Channel Stereo. (See pages 60 and 66.)
•When the digital multichannel software such as Dolby Digital or
DTS Digital Surround is played back, the appropriate multichannel
Surround mode is automatically activated (“DOLBY D” or “DTS
SURR”), and you can only turn on or off (“STEREO”) the surround
mode.
•For Dolby Digital 2 channel software, you can select “PLII MUSIC,”
“PLII MOVIE,” or off (“STEREO”) by pressing SURROUND MODE.
TV RETURN
ENTER
ON
SCREEN
CHOICE
AUDIO/
TV/VCR
SURROUNDMODE
FM MODE100+
CATV/DBSSURROUND
MODE button IMPORTANT:
When using the remote control, check to see if its
remote control mode selector is set to the correct
position:
To operate this system, set it to “AUDIO/TV/VCR.”AUDIO/
TV/VCR
CATV/DBS
Using Dolby Pro Logic II, Dolby
Digital and DTS Digital Surround
Once you have adjusted the sound, the adjustment is
memorized for each source.
From the remote control ONLY
1 Start playing back software.
When playing a conponent connected to the AUX IN or
the DIGITAL IN jack, change the source to AUX or AUX
DIGITAL. (See page 22.)
2 Press SURROUND MODE to activate
Surround mode.
Each time you press the button, Surround mode turns on
and off (stereo) alternately.
• If you are playing back software encoded with Dolby
Digital multichannel, “DOLBY D” is selected.
• If you are playing back software encoded with DTS
Digital Surround, “DTS SURR” is selected.
• If you are playing back any software other than the
above, you can select “PL II MUSIC” or “PL II MOVIE”
according to the source by pressing SURROUND
MODE.
If you like to adjust sound, go to step 3.
3 Press SOUND.
The 10 keys are activated for sound adjustments.
4 Press TEST to check if you can hear the sounds
through all the speakers at the equal level.
“TEST TONE L” and the corresponding signal indicator
starts flashing on the display window, and the test tone
comes out of the speakers in the following order:
] Left front speaker ] Center speaker ] Right front
speaker ] Right rear speaker ] Left rear speaker
] (back to the beginning)
L
TOP MENU MENU ZOOM
CONTROL– SUBWOOFER +EFFECT
–     CENTER     +
– 
    REAR-R     +
TEST
SLEEPTV VCR
SETTING
TV RETURN
ENTER
ON
SCREEN
CHOICE
AUDIO/
TV/VCR
SURROUNDMODE
FM MODE
123
45 6
789
100+10100+
CATV/DBS
SOUND–
–     REAR-L     +
PROGRESSIVE
Sound setting
buttonsSOUND
button
TEST
button
SURROUND
MODE button
EN33-36TH-V70[J]B02.3.13, 9:14 PM 35
 
						

							36
5 Adjust the speaker output levels
(–10 dB to +10 dB).
Adjust the center speaker and rear speaker levels
comparing to the sound from the front speakers.
• To adjust the center speaker level, press CENTER +/–.
• To adjust the left rear speaker level, press REAR-L +/–.
• To adjust the right rear speaker level, press REAR-R +/–.
6 Press TEST again to stop the test tone.
NOTES:
•When selecting “PL II MUSIC,”  “PL II MOVIE,” “DOLBY D,” or “DTS
SURR” as the surround mode, the SURROUND indicator lights up.
•You can adjust the speaker output levels without outputting the test
tone.
•When selecting DVD, AUX, or AUX DIGITAL as the source, you can
also adjust the speaker output levels using the choice menu. See
pages 55 and 61.
•When you have set the center speaker and rear speakers to
“NONE,” the test tone does not come out from those speakers, and
you cannot adjust the output level of those speakers. (See pages
60 and 66.)
•You can output the test tone in any surround mode, or even when
surround mode is not activated.
Using DAP Modes and All
Channel Stereo
Once you have adjusted the sound, the adjustment is
memorized for each source.
• You cannot use the DAP modes and All Channel Stereo if
the rear speakers are deactivated.
• You cannot adjust the effect level for “ALL CH ST.”
From the remote control ONLY:
1 Start playing 2 channel software—either
analog or Linear PCM.
When playing a conponent connected to the AUX IN or
the DIGITAL IN jack, change the source to AUX or AUX
DIGITAL.
TOP MENU MENU ZOOM
CONTROL– SUBWOOFER +EFFECT
–     CENTER     +
– 
    REAR-R     +
TEST
SLEEPTV VCR
SETTING
TV RETURN
ENTER
ON
SCREEN
CHOICE
AUDIO/
TV/VCR
SURROUNDMODE
FM MODE
123
456
78 9
100+10100+
CATV/DBS
SOUND–
–     REAR-L     +
PROGRESSIVESOUND button
EFFECT button
SURROUND
MODE button Sound setting
buttons
2 Press SURROUND MODE repeatedly until one
of the DAP modes—“LIVE CLUB,” “DANCE
CLUB,” “HALL,” “PAVILION”—or “ALL CH ST.”
appears on the display.
The DSP indicator also lights up on the display window.
If you like to adjust sound, go to step 3.
3 Press SOUND.
The 10 keys are activated for sound adjustments.
4 Adjust the speakers output levels
(–10 dB to +10 dB).
• To adjust the left rear speaker level, press REAR•L +/–.
• To adjust the right rear speaker level, press REAR•R +/–.
For “ALL CH ST.” only:
• To adjust the center speaker level, press CENTER +/–.
5 For DAP modes only:
Press EFFECT to select the effect level (1 to 5)
you want.
Each time you press the button, the effect level changes
as follows:
] DSP EFFECT 1 ] DSP EFFECT 2 ] DSP EFFECT 3
] DSP EFFECT 4 ] DSP EFFECT 5 ] (back to the
beginning)
As the number increases, the selected mode becomes
stronger (normally, set it to “EFFECT 3”).
NOTES:
•When selecting DVD, AUX, or AUX DIGITAL as the source, you can
also adjust the speaker output level using the choice menu. See
pages 55 and 61.
•You cannot select any DAP mode and All Channel Stereo when
software encoded with Dolby Digital or DTS Digital Surround is
played back.
EN33-36TH-V70[J]B02.3.13, 9:14 PM 36
 
						

							37
8.5MbpsTITLE 14TIME  1:25:58CHAP 23
OFF1/31/3 1/3TIMECHAP.
DVD-VIDEO
w q p 23456
7891
t r
OFF TIME
PROG.RND.
TIME         4:58TRACK 14
e
SVCD
1/4
w q
ST1
5641
789
t r
OFF TIME
PROG.RND.
TIME         4:58TRACK 14VCD
q
ST
5641
789
t r
OFF TIME
PROG.RND.
TIME         4:58TRACK 14CD
5641
789
Advanced operations
Using the on-screen bar
You can check the information of a disc while the disc is
loaded, and you can use some functions through the on-
screen bar.
Showing the on-screen bar
7Whenever a disc is loaded
Press ON SCREEN.
Each time you press the button, the on-screen bar appears
on the TV.
ENTER
ON
SCREEN
CHOICE
AUDIO/
TV/VCR
SURROUNDMODE
CATV/DBSON SCREEN
button
Contents of the on-screen bar
• When a DVD is played
• When an SVCD is played
• When a VCD is played
• When a CD is played
1:shows a disc type.
2:shows the current transfer rate (Megabits per second).
3:shows the current title number.
4:shows the current chapter number (for DVD) or track
number (for Video/Audio CD and SVCD).
5:shows the time information. See page 38.
6:shows the playback condition.
: appears during playback.
/: appears during fast forward/reverse.
/: appears during playback in forward slow-
motion/reverse slow-motion.
: appears while paused.
: appears while stopped.
7:Select this to change the time information (5).
See page 38.
8:Select this to repeat playback. See page 50.
9:Select this for the time search function. See page 45.
p:Select this for the chapter search function.
See page 44.
q:Select this to change the audio language or channel.
See pages 43 and 44.
w:Select this to change the subtitle language.
See page 42.
e:Select this to change the view angle. See page 40.
DVDAUDIO
CD
SUPER
VCD
VIDEO
CD
8.5MbpsDVD-VIDEOTITLE 14TIME  1:25:58CHAP 23
8.5MbpsDVD-VIDEOTITLE 14TIME  1:25:58CHAP 23
8.5MbpsTITLE 14TIME  1:25:58CHAP 23
OFF1/31/3 1/3TIMECHAP.
DVD-VIDEO
OFF
(The On screen bar disappears)
 (back to the beginning) IMPORTANT:
When using the remote control, check to see if its
remote control mode selector is set to the correct
position:
To operate this system, set it to “AUDIO/TV/VCR.”
This section explains advanced operations of DVD, Video CD, SVCD, and Audio CD playback using the remote control.
For MP3 playback, see page 51, and for JPEG playback, see page 53.
•
DVDAUDIOCDSUPERVCDVIDEOCD shows the types of discs the operation is available for.
¥ Before operating the DVD player from the remote control, press DVD to use the remote control for the disc operations.
¥ Turn on your TV, and select the correct input mode on the TV.
¥If “
” appears on the TV screen when pressing a button, the disc cannot accept an operation you have tried to do, or
information required for that operation is not recorded on the disc.
AUDIO/
TV/VCR
CATV/DBS
EX: When a DVD is played
EN37-50TH-V70[J]B02.3.13, 9:17 PM 37