JVC Th A30 Instructions

							24
English
Adjusting Dolby Surround
You can adjust the following settings while activating Dolby
Surround.
It is recommended that you make adjustments from your actual
listening point while listening to reproduced sounds.
–Output balance for the front speakers
–Output balance for the rear speakers
–Output level for the rear speakers*
–Output level for the subwoofer
• When Dolby 3 Stereo is activated, you cannot adjust the rear
speakers.
* The adjustment is separately memorized for Digital Multichannel
Surround (Dolby Digital and DTS Digital Surround), and for
Dolby Pro Logic.
•Dolby Surround cannot be used with DSP modes. Once one of
Dolby Surround is activated, DSP modes in use will be canceled.
Before you start, remember...
•There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 
3 again.
1Press AUX to select the external
component as the source.
2Start playing a source encoded with Dolby
Surround.
3Press PRO LOGIC repeatedly on the
remote control to select Dolby Pro
Logic or Dolby 3 Stereo.
The PRO LOGIC indicator lights up on the display.
•Each time you press the button, the indication changes as
follows:
Now, you are ready to start adjustments.
•To adjust the output balance for the front speakers and the rear
speakers, go to the next step.
•To adjust the output level for the center speaker, the rear speakers,
and the subwoofer, go to step 
5 on the next page.
4To adjust the output balance for the front
speakers and the rear speakers
1) Press SOUND repeatedly until one of
the following adjustment indications
appears on the display.
•Each time you press the button, the adjustment indication
on the display changes as follows:
00 F (Front) 00: To adjust the output balance for the front
speakers.
00 R (Rear) 00: To adjust the output balance for the rear
speakers.
•When selecting “3 STEREO,” you cannot adjust the output
balance for the rear speakers.
•“00 F 00” and “00 R 00” are the initial settings (the output
balances are at the center position). If you have already
changed the setting, another value will appear.
2) Press 3 or 2 to adjust the
output balance.
3: Decreases the left speaker
output, or restores the right
speaker output.
2: Decreases the right speaker
output, or restores the left
speaker output.
•Each output balance changes from
OFF (silence), –06 (most reduction) to 00 (no reduction).
3) Repeat 1) and 2) for setting the other speakers.
PRO LOGIC
PRO LOGIC3 STEREO
STEREO
(canceled)
00 F 00
00 R 00CEN
Normal indication
(canceled)SW
REAR
SOUND
ENTER
AUX
D.R.C
Activating Dynamic Range Compression
You can enjoy a powerful sound even at a low volume level by
compressing the dynamic range (difference between the maximum
and minimum sounds).
• This function takes effect only when Dolby Digital is activated.
From the remote control ONLY:
Press D.R.C.
•Each time you press the button, the dynamic range
compression mode alternates between on and off.
Select “DRC ON” while watching the DVD at night. (You can
obtain a powerful sound at a low volume.)
TO BE CONTINUED ON THE NEXT PAGE
EN20-26TH-A30[C].pm602.6.6, 11:44 AM 24
 
						

							25
English
ENTER
HALLTHEATER
Normal
indication
(canceled)LIVE CLUB
DANCE CLUB
DSP MODE
Adjusting DSP Modes
You can adjust the following settings while activating DSP modes.
It is recommended that you make adjustments from your actual
listening point while listening to reproduced sounds.
–Output balance for the front speakers
–Output balance for the rear speakers
–Output level for the rear speakers
–Output level for the subwoofer
•DSP modes cannot be used with Dolby Surround. Once one of
DSP modes is activated, Dolby Surround in use will be canceled.
•When you play back a DVD encoded with Dolby Digital or DTS
Digital Surround, DSP MODE button (or DSP button on the center
unit) does not work.
Before you start, remember...
•There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 
2 again.
1Select and play any source except Dolby Digital
or DTS Digital Surround.
2Press DSP MODE (or DSP on the front
panel) repeatedly to select the desired
DSP mode.
The DSP indicator lights up on the display while the DSP modes
are activated.
•Each time you press the button, DSP mode changes as follows:
Now, you are ready to start the adjustment.
•To adjust the output balance for the front speakers and the rear
speakers, go to the next step.
•To adjust the output level for the rear speakers, go to step 
4 on the
next page.
Creating Realistic Sound Fields
B.SEARCHREW FF
F.SEARCH
RETURN TOP MENUENTER
VOLUME
MENU
VCR CHANNEL
TUNING
MUTING
123
456
789
0
REMAIN
PROGRAM
D.R.C ZOOMSETUP
DSP MODE
SLEEP
TEST PRO LOGICSETTINGSOUND
CLEAR REPEATANGLESLOW
SEARCH A-B REPEAT
2  3
SOUND
DSP MODE
5To adjust the output level for the center speaker,
the rear speakers, and the subwoofer
1) Press SOUND repeatedly to select the
“CEN,” “REAR,” or “SW.”
•Each time you press the button, the adjustment
indication on the display changes as follows:
CEN (Center) : To adjust the output level for center
speaker (from –6 dB to +6 dB).
REAR: To adjust the output level for rear
speakers (from –6 dB to +6 dB).
SW (Subwoofer) : To adjust the output level for subwoofer
(from –6 dB to +6 dB).
•When selecting “3 STEREO,” you cannot adjust the output
levels for the rear speakers.
•“CEN 0dB,” “REAR 0dB,” and “SW 0dB” are the initial
settings. If you have already changed the settings, another
value will appear.
2) Press 3 or 2 to adjust the
output level.
3: Increases the output level.
2: Decreases the output level.
3) Repeat 1) and 2) for setting
the other speakers.
00 F 00
00 R 00CEN
Normal indication
(canceled)SW
REAR
SOUND
EN20-26TH-A30[C].pm602.6.6, 11:44 AM 25
 
						

							26
English
00 F 00
00 R 00 CEN
Normal indication
(canceled)SW
REAR
4To adjust the output level for the rear speakers
1) Press SOUND repeatedly until “REAR”
appears on the display.
•Each time you press the button, the adjustment
indication on the display changes as follows:
REAR: To adjust the output level for rear speakers
(from –6 dB to +6 dB).
•“REAR 0dB” is the initial setting. If you have already
changed the setting, another value will appear.
2) Press 3 or 2 to adjust the
output level.
3: Increases the output level.
2: Decreases the output level.
SOUND
3To adjust the output balance for the front
speakers and the rear speakers
1) Press SOUND repeatedly until one of
the following adjustment indications
appears on the display.
•Each time you press the button, the adjustment
indication on the display changes as follows:
00 F (Front) 00: To adjust the output balance for the front
speakers.
00 R (Rear) 00: To adjust the output balance for the rear
speakers.
•“00 F 00” and “00 R 00” are the initial setting (the output
balances are at the center position). If you have already
changed the setting, another value will appear.
2) Press 3 or 2 to adjust the
output balance.
3: Decreases the left speaker
output, or restores the right
speaker output.
2: Decreases the right speaker
output, or restores the left
speaker output.
•Each output balance changes from
OFF (silence), –06 (most reduction) to 00 (no reduction).
3) Repeat 1) and 2) for setting the other speaker.
00 F 00
00 R 00CEN
Normal indication
(canceled)SW
REAR
SOUND
ENTER
ENTER
EN20-26TH-A30[C].pm602.6.6, 11:44 AM 26
 
						

							27
English
Disc Introduction—DVD/VCD/CD
•On some DVD or VCD/SVCD discs, their actual operations
may be different from what is explained in this manual. This is
due to the disc programming and disc structure, but not a
malfunction of this system.
•The following discs cannot be played back:
–DVD-Audio, DVD-ROM, DVD-RAM, DVD-R,
DVD-RW, CD-I, (CD-I Ready), Photo CD, etc.
Playing back these discs will generate noise and damage the
speakers.
* Note on Video Format
This unit accommodates the color system of NTSC. Note that the unit
cannot playback the disc recorded with the color system of PAL.
If a DVD recorded with the color system of PAL is loaded,
“WRONG DISC” appears on the display and playback cannot
start.
** Note on Region Code
DVD players and DVD Video discs have their own Region Code
numbers. This system only can play back DVD discs whose Region
Code numbers include “1.”
If a DVD with the inadequate Region Code numbers is loaded,
“REGION ERR” appears on the display and playback cannot start.
Disc Mark Video Region Code
Type (Logo) Format*Number**
DV D
Video
NTSC1
ALL
Video
CD This system has been designed to play back the following discs: DVD,
Video CD, Super Video CD (SVCD), Audio CD, CD-R, and CD-RW.
•This system can also play back MP3 files recorded on CD-Rs and
CD-RWs. For in-depth information about what MP3, see “MP3
Introduction” on page 43.
Discs you can play:
Example 1: DVD disc
Example 2 : Video CD/Audio CD
Examples:Disc structure—DVD, Video CD (VCD/SVCD) and Audio CD (CD)
A DVD disc consists of Titles, and each title may be divided into
some Chapters. (See Example 1.)
For example, if a DVD disc contains some movies, each movie may
have its own title number, and it may be further divided into some
chapters.
On the other hand, a VCD/SVCD or CD consists of Tracks. (See
Example 2.)
In general, each song has its own track number. (On some discs,
each track may also be divided by Indexes.)
When playing back a VCD/SVCD with Playback Control (PBC)
function, you can select what to view using the menu shown on the
TV screen. (While operating a Video CD using the menu, some of
the functions such as Repeat and Track Search may not work.)
Notes on CD-R and CD-RW
User-edited CD-Rs (Recordable) and CD-RWs (Rewritable) can be
played back only if they are already “finalized.”
•The system can play back CD-Rs or CD-RWs recorded on a
personal computer if they have been recorded in the audio CD
format or recorded in MP3 format (see page 43).
However, they may not be played back depending on their
characteristics or recording conditions.
•Before playing back CD-Rs or CD-RWs, read their instructions or
cautions carefully.
•Some CD-Rs or CD-RWs may not be played back on this unit
because of their disc characteristics, damage or stain on them, or if
the built-in lens is dirty.
•CD-RWs may require a longer readout time. This is caused by the
fact that the reflectance of CD-RWs is lower than for regular CDs.
If “” appears on the TV screen when pressing a button,
the disc cannot accept an operation you have tried to do, or
information required for that operation is not recorded in the disc.
NOTICE : In some cases, without showing “
,” operations
will not be accepted. IMPORTANT:
Before performing any operations, make sure of the following....
•Check the connection with the TV.
•Turn on the TV and select the correct input on the TV to view the
pictures or on-screen indications on the TV screen.
•For DVD playback, you can change the Setup menu setting to
your preference. (See pages 49 to 53.)
Super
Video
CD
COMPACT
DIGITAL AUDIO
Audio
CD
CD-R
CD-RW
EN27-36TH-A30[C].pm602.6.6, 11:45 AM 27
 
						

							28
English
Basic Disc Operations
To start playback
Press 3/8.
The source is automatically changed to the
DVD player.
“WAIT” appears on the display for a while,
then the detected disc type appears—DVD, VCD, CD, or MP3. (If
your TV is turned on, the mark corresponding to the detected disc
type appears on the TV screen.)
•When a disc is not loaded, “NO DISC” appears on the display.
Disc play starts from the first chapter or track of the selected disc.
•If a menu appears while playing a DVD or VCD with PBC
function, see “Disc Menu-Driven Playback” (for DVD) on page 31
or “Disc Menu-Driven Playback (Only for VCD)” on page 38.
Note:
If “WRONG PARENTAL CODE” appears on the TV screen, Parental
Lock is in use. You cannot play back a DVD containing violent scenes
or those not suitable for your family members.
To play back such a disc, cancel the Parental Lock. (See page 52.)
To stop playback for a moment
Press 3/8.
While pausing, minute and second digit
 of elapsed playing time flashes on the display.
•To resume play, press 3/8 again.
To go to another chapter or track
Press ¢ or 4 repeatedly during playback.
•¢: Skips to the beginning of the next or succeeding chapter or
track.
•4:While a DVD,  a VCD with PBC or MP3 is played back
Goes back to the beginning of the previous chapter or track.
While a CD or a VCD without PBC is played back
Goes back to the beginning of the current or previous track.
To go to another title (only possible on a DVD)
or track (only possible on a CD and VCD)
directly using the number buttons
Pressing the number buttons before or during play allows you to
start playing the title/track number you want. (If your TV is turned
on, the on-screen bar is pulled down automatically on the TV
screen.)
•To select number 1 to 9, press the corresponding number button
(then press ENTER or wait for 5 seconds).
•To select number 15, press 1, 5.
•To select number 23, press 2, 3.
To stop during playback
Press 7.
(If your TV is turned on, “
 STOP” appears
on the TV screen.)
•When an MP3 disc is played back, playback
stops completely.
•This system can memorize the end point even when you press 7.
When you start playback again by pressing 3/8, playback begins
from where it has been stopped—Resume play.
•To stop completely, press 7 twice. (“7 STOP” appears on the TV
screen.) The disc type appears on the display.
The DVD player goes on working for 3 minutes after playback
stops.
To remove the disc
Press 0 on the front panel.
The disc tray comes out.
To close the disc tray, press 0 again.
•If you do not press the button, the disc tray closes
automatically 3 minutes after.
TUNER PRESET
TUNER PRESET
TUNER PRESET
DISPLAY
B.SEARCH DOWN
REWUP
FF
F.SEARCH STEP
TV/VIDEO
TV VOLUME
TV CHANNEL
SUBTITLE
TV STANDBY/ON
AUDIO
VCR
VCR 
CONTROL
TUNER PRESET
ENTER
AUDIO/
FM MODE
VCR CHANNEL
TUNING
DVD FM/AM AUX
PROGRESSIVE
7
3/8 ¢ 4
Title No. Elapsed playing 
time Chapter No.
Track No.
Elapsed playing 
time
Track No.
Elapsed playing 
time
Playback information on the display
DVD
VCD/CD
MP3
SVCD can be operated by using the VCD operation
procedure.
EN27-36TH-A30[C].pm602.6.6, 11:45 AM 28
 
						

							29
English
DVD Playback
ANGLE
DISPLAY
B.SEARCH DOWN
REWUP
FF
F.SEARCH
RETURN STEP
TV/VIDEO
TV VOLUME
TV CHANNEL
SUBTITLE
TOP MENUTV STANDBY/ON
AUDIO
VCR
VCR 
CONTROL
TUNER PRESET
ENTER
VOLUME
MENU
AUDIO/
FM MODE
VCR CHANNEL
TUNING
DVD FM/AM AUX
MUTING
123
456
789
0
REMAIN
PROGRAM
D.R.C ZOOMSETUP
PROGRESSIVE
DSP MODE
SLEEP
TEST PRO LOGICSETTINGSOUND
CLEAR REPEATANGLESLOW
SEARCH A-B REPEAT
123
456
789
0
AUDIO/
FM MODESUBTITLE
3
3
3
Some DVDs contain several audio languages, subtitles, and multi-
angle views.
When you find the following marks on the DVD or its package, you
can select these elements recorded on the DVD.
Subtitles are recorded on the disc. The number
inside the mark indicates the total number of the
recorded subtitles.
Several audio languages are recorded on the disc.
The number inside the mark indicates the total
number of the recorded audio languages.
Multi-angle views are recorded on the disc. The
number inside the mark indicates the total number
of the recorded multi-angle views.
If you cannot find out whether your disc contains these features
listed above, you can check it by showing the on-screen bar.
For basic disc operations such as inserting a disc, starting
playback, and moving to another chapters, see “Basic DVD
Operations” on pages 12, 13, and “Basic Disc Operations” on
page 28.
1:Disc type
DVDVCD SVCD CD MP3
2:Current title and total number of the titles on the
disc
•Ex.: 1st title is playing out of 3 titles recorded.
3:Current chapter and total number of the chapters
in the current title
•Ex.: 1st chapter is playing out of 5 chapters recorded.
4:Elapsed playing time or remaining time
You can change the play time indication  by pressing
REMAIN. See page 31 for more details.
5:Subtitle language indication
•Ex.: When no subtitle is recorded on the disc.
See page 30 for more details.
6:Audio language indication
•Ex.: Original sound (default) is selected out of 3 audio
languages recorded. See page 30 for more details.
7:Signal format indicator
•Signal format type—Linear PCM (stereo), Dolby Digital,
and DTS Digital Surround—will be indicated.
Ex.: When the disc is encoded with Dolby Digital.
8:Repeat mode indicator
•Ex.: When repeat mode is turned off.
See page 33 for more details.
9:Multi-angle view indicator
•Ex.: When only a single angle-view is recorded on the
disc. See page 30 for more details.
Showing the On-Screen Bar
You can show the following information on the TV screen while a
disc is loaded.
From the remote control ONLY:
Press DISPLAY.
•Each time you press the button, the following on-
screen bar appears in sequence.
1
5678923 4
On-screen bar goes off.
DISPLAYDISPLAY
 
						

							30
English
Selecting the Audio Languages
While playing back a DVD containing audio languages (sound
track), you can select the language (sound track) to listen to.
•You can set your favorite audio language as the initial audio
language. (See page 49.)
Press AUDIO/FM  MODE.
The on-screen bar appears on the TV screen for a while.
•Each time you press the button, the audio language
changes as follows:Ex.: When the disc has 3 multi-angle views Ex.: When the disc has 3 selections—English,
French, Spanish and no subtitle (OFF)
ANGLE         3
ANGLE         1ANGLE         2
Ex.: When the disc has 3 selections—English,
French, and Spanish
Selecting the Subtitles
While playing back a DVD containing subtitles in different
languages, you can select the subtitle to be displayed on the TV
screen.
•You can set your favorite subtitle language as the initial language
shown on the screen. (See page 49.)
From the remote control ONLY:
Press SUBTITLE.
The on-screen bar appears on the TV screen for a while.
•Each time you press the button, the subtitle language
changes as follows:SUBTITLE
DEF 1/3 1/1OFF  /3
OFF   /3ENG 1/3
SPA 3/3FRE 2/3
ENG 1/3FRE 2/3
SPA 3/3
ENG 1/3 1/1ENG 1/3
AUDIO/
FM MODE
ANGLE
1/32/3
3/3
Selecting the Multi-Angle Views
While playing back a DVD containing multi-angle views, you can
view the same scene at different angles.
• When you play back the DVD containing multi-angle views, 
appears on the TV screen.
From the remote control ONLY:
Press ANGLE.
•Each time you press the button, the view angle changes.
Note:
When the on-screen bar is shown on the TV screen, Multi angle view
indication also changes as follows:
EN27-36TH-A30[C].pm602.6.6, 11:45 AM 30
 
						

							31
English
DVD Playback
TOP MENUMENURETURN MUTING
TOP MENUMENU RETURN MUTING
ENTER
Disc Menu-Driven Playback
Disc menu-driven playback is possible while playing back a DVD
with menu (menu may be still pictures or moving pictures
depending on the disc).
• When operating a disc using the disc menu, refer also to the
instructions supplied for the disc.
DVD discs generally have their own menus or title lists. A menu
usually contains various information about the disc and playback
selections. On the other hand, a title list usually contains titles of
movies and songs recorded.
From the remote control ONLY:
1Press MENU or TOP
MENU.
A menu or title list will appear
on the screen.
“MENU” appears on the display.
• On some DVDs, a menu will
automatically appear on the
screen after playback starts.
2Select a desired item on the
menu or on the title list, using
3/2/5/∞ and ENTER.
The unit starts playback of the selected
item.
• On some discs, you can also select items
by pressing the number buttons
corresponding to the item numbers
listed.
Checking the Remaining Time
While playing back a DVD, you can check the remaining time to be
played back.
From the remote control ONLY:
Press REMAIN.
The on-screen bar and the current play time indication
appear on the TV screen for a while.
• Each time you press the button, the following indication appears
on the screen:
REMAIN TIME:TITLE
: Select this to show the remaining time of the current title.
CHAPTER TIME
: Select this to show the elapsed playing time of the current
chapter.
REMAIN TIME:CHAPTER
: Select this to show the remaining time of the current chapter.
TITLE TIME
: Select this to show the elapsed playing time of the current title.
TITLE TIME
CHAPTER TIME
REMAIN TIME:CHAPTERREMAIN TIME:TITLE 
REMAIN
3/2/5/∞
ENTER
TOP MENU
DISPLAY
B.SEARCH DOWN
REWUP
FF
F.SEARCH
RETURN STEP
TV/VIDEO
TV VOLUME
TV CHANNEL
SUBTITLE
TOP MENUTV STANDBY/ON
AUDIO
VCR
VCR 
CONTROL
TUNER PRESET
ENTER
VOLUME
MENU
AUDIO/
FM MODE
VCR CHANNEL
TUNING
DVD FM/AM AUX
MUTING
123
456
789
0
REMAIN
PROGRAM
D.R.C ZOOMSETUP
PROGRESSIVE
DSP MODE
SLEEP
TEST PRO LOGICSETTINGSOUND
CLEAR REPEATANGLESLOW
SEARCH A-B REPEAT
123
456
789
0Number
buttons
CLEARREMAINMENU
SEARCH 1
¡
EN27-36TH-A30[C].pm602.6.7, 1:44 PM 31
 
						

							32
EnglishSearching for a Particular Point
You can search for a particular point while playing a disc—Va r i a b l e
Speed Forward/Reverse Search.
•No sound comes out during Variable Speed Forward/Reverse
Search.
To fast-forward the chapter—Variable Speed
Forward Search
From the remote control ONLY:
Press ¡ during playback or pause.
•Each time you press the button, the search speed
changes as follows:
To reverse the chapter—Variable Speed Reverse
Search
From the remote control ONLY:
Press 1 during playback or pause.
•Each time you press the button, the search speed
changes as follows:
To resume normal play
Press 3/8.
PLAY (Back play)
x2x4
x8
PLAY (Normal play)
x2x4
x8
B.SEARCH
TUNER PRESET
F.SEARCH
Moving to a Particular Portion Directly
You can move to another title, chapter, or particular scene in the
chapter directly.
From the remote control ONLY:
1Press SEARCH during playback or pause.
•Each time you press the button, the following
indication appears on the screen:
TITLE – –: Select this to move to another title.
CHAPTER – – –: Select this to move to another chapter.
TIME – –: – –: – –: Select this to move to a particular scene.
2Press the number buttons to
select a desired title, chapter,
or playing time.
The unit starts playback of the selected
item. (The on-screen bar appears for a
while.)
How to input the title and chapter number
Press the number buttons corresponding to the number, then wait
for about 5 seconds or press ENTER to start playback.
•To select number 5, press 5, then ENTER.
•To select number 12, press 1, 2, then ENTER.
•To select number 22, press 2, 2, then ENTER.
How to input the playing time
Press the number buttons to input the playing time, then wait for
about 5 seconds or press ENTER to start playback at the selected
elapsed playing time.
•To input time “00:45:23,” press 4, 5, 2, 3.
•To input time “01:23:45,” press 1, 2, 3, 4, 5.
•To cancel a mis-entry, press CLEAR.
Each time you press the button, the last entry will be erased.
Note:
When you want to move to another title directly, you can move to it by
simply pressing the corresponding number buttons (without pressing
SEARCH in step 
1).
Canceled
TITLE – –
TIME – – : – – : – – CHAPTER – – –
SEARCH
123
456
789
0
EN27-36TH-A30[C].pm602.6.6, 11:45 AM 32
 
						

							33
English
DVD Playback
Repeating Playback
Repeat play cannot be used in the following cases:
•When you enjoy program play
7 Repeat Play
From the remote control ONLY:
Press REPEAT repeatedly.
The indication corresponding to the selected mode appears
on your TV.
•Each time you press the button, Repeat mode changes as follows:
REPEAT:CHAPTER: Current chapter will be repeated.
REPEAT:TITLE: Current title will be repeated.
REPEAT OFF: Repeat play is canceled. (Normal play
is resumed.)
Note:
When the on-screen bar is shown on the TV screen, Repeat mode
indication also changes as follows:
Example:
REPEAT:CHAPTERREPEAT:TITLE
REPEAT OFF
REPEAT
REPEAT:CHAPTER REPEAT:TITLE
REPEAT OFF
From the remote control ONLY:
1Press A–B REPEAT to select the start
point.
“RPT A–” appears on the display and “REPEAT:A–”
appears on the TV–screen.
2Press A–B REPEAT again to select the
end point.
“RPT A–” changes to “RPT A–B” and “REPEAT:A–
” changes to “REPEAT:A–B,”  then A–B Repeat begins.
The unit automatically locates point A and starts repeated
playback between points A and B.
To cancel A–B Repeat
Press A–B REPEAT again.
“RPT OFF” appears on the display and “REPEAT OFF”
appears on the TV–screen.
Note:
When the on-screen bar is shown on the TV screen, Repeat mode
indication also changes as follows:
On some DVDs, A–B Repeat may not be used even within the
same title. This is due to their disc structures, and not a
malfunction of the unit.
A-B REPEAT
A-B REPEAT
A-B REPEAT
7 A–B Repeat
While playing, you can also select a portion you want to repeat.
•A–B repeat is not performed between different titles.
•An interval of more than 5 seconds is required between point A
and point B.
2 3
ENTER
REPEAT
A-B REPEAT
DISPLAY
B.SEARCH DOWN
REWUP
FF
F.SEARCH
RETURN STEP
TV/VIDEO
TV VOLUME
TV CHANNEL
SUBTITLE
TOP MENUTV STANDBY/ON
AUDIO
VCR
VCR 
CONTROL
TUNER PRESET
ENTER
VOLUME
MENU
AUDIO/
FM MODE
VCR CHANNEL
TUNING
DVD FM/AM AUX
MUTING
123
456
789
0
REMAIN
PROGRAM
D.R.C ZOOMSETUP
PROGRESSIVE
DSP MODE
SLEEP
TEST PRO LOGICSETTINGSOUND
CLEAR REPEATANGLESLOW
SEARCH A-B REPEAT
3/8
PROGRAM 7REPEAT:A–
REPEAT:A–B
EN27-36TH-A30[C].pm602.6.6, 11:45 AM 33