JVC Projector DLA-SH7NL User Manual

21
Connection During Single-Screen Mode Display
Below is the connection example for fo ur-channel signals from the computer.
For two-channel signals from the computer, connect to th e [DVI 1] and [DVI 3] terminals of this projector.
NOTE:                                                                                                                                                                                 
●Depending on your DVI-D cable, the signal  may attenuate and the image become unstable....

22
Connection and Installation
Connection During Two-Screen/
Four-Screen Mode Display
The two-screen/four-screen mode enables simultaneous display of signals from two or four computers.
To select the two-screen mode, set  ADisplay Mode B in the Setting menu to  ADouble B. To select the four-screen mode, set 
A Display Mode B to  ACross B. ( A Page 38)
Possible Input Signals and Projected Image
NOTE:...

23
Connection Example During Two-Screen Mode
Connection Example During Four-Screen Mode
NOTE:                                                                                                                                                                                
●Depending on your DVI-D cable, the signal may attenuate and the image become unstable....

24
Network Settings
Connect this projector, the computer for controlling this 
projector, and the switching hub using LAN cables, 
followed by configuring the network.
Connection Example
When assigning a static IP address
You can acquire the IP address from the controlling 
computer simply by configuring a network that consists of 
this projector, the controlling computer, and switching 
hub. Please refer to technical books on networks for 
details.
NOTE:...

25
1 Check to ensure that this projector, computer, and switching hub are properly connected
2 Connect the power cord to the power input terminal of this projector
You can secure the power cord to this projector.AAttach the plug holder to the power cord.
B Insert the plug holder into the projector until the upper and lower securing levers are locked.
3 Insert plug into the power outlet on the wall
4 Remove the lens cap
5 Turn on the main power of the projector to set to [I]
●The [STANDBY/ON], [LAMP], and...

26
Network Settings
Set the IP address for this projector. There are 2 methods to set the IP address.
Assigning a static IP address
 Assigning an IP address from the DHCP Server
Assigning a static IP address
The  AIP Address Setting B of this projector is set to  ASTATIC IP B (the DHCP client function is OFF) by default.
Upon turning on the power, this projector starts running with the following IP address.
 IP Address : 192.168.0.2
 Subnet Mask : 255.255.255.0
 Default Gateway : 192.168.0.254
 IP...

27
Setting (Changing) the IP address of this 
projector
1 Launch the Internet Explorer on the 
computer
2 Check if the proxy has been set in the  ALAN 
Setting B of the Internet Explorer
A Click  ATo o l s B and select  AInternet Options B
B Click  AConnections B and click  ALAN Setting B
C Check if the check for  AUse a proxy server for your 
LAN B has been selected
● If the check mark has been  selected, deselect it.
3 Check if the  AActive scripting B of the Internet 
Explorer is disabled
A Click...

28
Network Settings
Assigning a static IP address 
(Cont’d)
4 
Enter Ahttp://192.168.0.2B in the address field 
of the Internet Explorer, and click 
AGoB
● A login screen for this projector appears.
NOTE:                                                                             
●When  ALAN Setting B in Internet Explorer is set to  AUse 
a proxy server for your LAN B it may not be possible to 
designate addresses directly. Change the proxy 
settings.
● If a  ASecurity Warning B screen appears, click...

29
Assigning IP Address from the 
DHCP Server
The IP address is automatically assigned by the DHCP 
server.
1 After connecting, turn on the main power
●Refer to Page 24 on the details of connection.
● Refer to Page 25 on procedures to turn on the main 
power.
2 Set the  ADHCP Client B setting of this 
projector to  ADHCP B
●The  ADHCP Client B of this projector is set to 
A STATIC IP B (the DHCP client function is OFF) by 
default. When assigning an IP address from the 
DHCP server, access this projector...

30
 Operation and Settings
If setting for this projector is not completed, refer to AUser 
Settings Menu B(A Page 33) upon turning on the power 
and configure the settings accordingly.
Once the basic settings are configured, this projector can 
be used by simply performing the following operation 
procedures.
PREPARATION:                                                                  
● Remove the lens cap.
●
Connect this projector to the computer. (APage 21, 23)
● Connect the LAN cable. ( APage 24)
1...