JVC Hd Z70rx5 Instructions

							LT-Z70/56RX5 / LCT1911-001A / English
29
ENGLISH
CH/CC numbers
When you want to use the INSERT function on page 22, find the CH/CC number corresponding to the Channel number of the TV channel from this 
table.
US:  The US channel numbers are the channel numbers used in the United States, Philippines, etc.
CCIR:  The CCIR channel numbers are the channel numbers used in the Middle East, Southeast Asia, etc.
OIRT:  The OIRT channel numbers are the channel numbers used in Eastern Europe, Russia, Vietnam, etc.
AUSTRALIA:  The AUSTRALIA channel numbers are the channel numbers used in Australia, etc.
CCChannel
US CCIR OIRT AUSTRALIA
CC01 S-1 AU-5
CC02 S-2
CC03 S-3
CC04 S-4
CC05 S-5
CC06 S-6 AU-5A
CC07 S-7
CC08 S-8
CC09 S-9
CC10 S-10
CC11 S-11
CC12 S-12
CC13 S-13
CC14 A S-14
CC15 B S-15
CC16 C S-16
CC17 D S-17
CC18 E S-18
CC19 F S-19
CC20 G S-20
CC21 H S-21
CC22 I S-22
CC23 J S-23
CC24 K S-24
CC25 L S-25
CC26 M S-26
CC27 N S-27
CC28 O S-28
CC29 P S-29
CC30 Q S-30
CC31 R S-31
CC32 S S-32
CC33 T S-33
CC34 U S-34
CC35 V S-35
CC36 W S-36
CC37 W+1 S-37
CC38 W+2 S-38
CC39 W+3 S-39
CC40 W+4 S-40
CC41 W+5 S-41
CC42 W+6
CC43 W+7
CC44 W+8
CC45 W+9
CC46 W+10
CC47 W+11
CC48 W+12
CC49 W+13
CC50 W+14
CC51 W+15
CC52 W+16
CC53 W+17
CC54 W+18
CC55 W+19
CC56 W+20
CC57 W+21
CC58 W+22
CC59 W+23
CC60 W+24
CC61 W+25
CC62 W+26
CC63 W+27
CC64 W+28
CC75 X
CC76 Y R3
CC77 Z R4 AU-3
CC78 Z+1 R5
CC79 Z+2 AU-4
CC95 A-5
CC96 A-4
CC97 A-3
CC98 A-2
CC99 A-1CHChannel
US CCIR OIRT AUSTRALIA
CH02 US-2 E2 R1 AU-0
CH03 US-3 E3 AU-1
CH04 US-4 E4 R2 AU-2
CH05 US-5 E5 R6 AU-6
CH06 US-6 E6 R7 AU-7
CH07 US-7 E7 R8 AU-8
CH08 US-8 E8 R9 AU-9
CH09 US-9 E9
CH10 US-10 E10 R10 AU-10
CH11 US-11 E11 R11 AU-11
CH12 US-12 E12 R12
CH13 US-13
CH14 US-14,  W+29
CH15 US-15,  W+30
CH16 US-16,  W+31
CH17 US-17,  W+32
CH18 US-18,  W+33
CH19 US-19,  W+34
CH20 US-20,  W+35
CH21 US-21,  W+36 E21
CH22 US-22,  W+37 E22
CH23 US-23,  W+38 E23
CH24 US-24,  W+39 E24
CH25 US-25,  W+40 E25
CH26 US-26,  W+41 E26
CH27 US-27,  W+42 E27
CH28 US-28,  W+43 E28
CH29 US-29,  W+44 E29
CH30 US-30,  W+45 E30
CH31 US-31,  W+46 E31
CH32 US-32,  W+47 E32
CH33 US-33,  W+48 E33
CH34 US-34,  W+49 E34
CH35 US-35,  W+50 E35
CH36 US-36,  W+51 E36
CH37 US-37,  W+52 E37
CH38 US-38,  W+53 E38
CH39 US-39,  W+54 E39
CH40 US-40,  W+55 E40
CH41 US-41,  W+56 E41
CH42 US-42,  W+57 E42
CH43 US-43,  W+58 E43
CH44 US-44,  W+59 E44
CH45 US-45,  W+60 E45
CH46 US-46,  W+61 E46
CH47 US-47,  W+62 E47
CH48 US-48,  W+63 E48
CH49 US-49,  W+64 E49
CH50 US-50,  W+65 E50
CH51 US-51,  W+66 E51
CH52 US-52,  W+67 E52
CH53 US-53,  W+68 E53
CH54 US-54,  W+69 E54
CH55 US-55,  W+70 E55
CH56 US-56,  W+71 E56
CH57 US-57,  W+72 E57
CH58 US-58,  W+73 E58
CH59 US-59,  W+74 E59
CH60 US-60,  W+75 E60
CH61 US-61,  W+76 E61
CH62 US-62,  W+77 E62
CH63 US-63,  W+78 E63
CH64 US-64,  W+79 E64
CH65 US-65,  W+80 E65
CH66 US-66,  W+81 E66
CH67 US-67,  W+82 E67
CH68 US-68,  W+83 E68
CH69 US-69,  W+84 E69
HD-Z70&56RX5_Eng.book  Page 29  Tuesday, October 11, 2005  9:17 PM
 
						

							LT-Z70/56RX5 / LCT1911-001A / English
30
ENGLISH
Appendix
Changing the Lamp
This television uses a 110-Watt high-pressure mercury lamp to project images onto the television screen. When the lamp nears the end of its operating 
life, you may notice the picture becoming dark. When the picture begins to darken, or the lamp burns out, it is time to replace the lamp. The following 
instructions will tell you how to safely replace the lamp.
Replacement Lamp Kit
Before replacing the lamp, you will need to purchase a replacement kit, part number TS-CL110C. To purchase this kit, consult your dealer.
The replacement kit will include the following:
1 High-Pressure Mercury Lamp 1 Instruction Manual
Because the lamp contains a small amount of mercury, it cannot be disposed of with normal trash.
Lamp Message
If this message appears when you turn the TV on, you need to replace the lamp. See “How to Replace the Lamp” on next page how to replace the 
lamp.
• This message will appear every time you turn on the TV when the lamp needs to be replaced. Press the OK button to make the message disappear, 
or replace the lamp. 
WARNING!
It is very important that you NEVER TOUCH THE GLASS SURFACE OF THE NEW LAMP. Touching the glass surface will
deposit oils from your hand onto the lamp surface. When the lamp heats up to its operating temperature, the oil will cause
a difference in temperature on the lamp surface that will likely cause the lamp to break.
Replace the lamp with part number TS-CL110C only!
 The television is designed to work specifically with this lamp. Using a 
different lamp, or a third-party manufacturer’s lamp could cause a malfunction and or damage to the television.
WARNING!
Under operating conditions, THE LAMP WILL GET EXTREMELY HOT AND WILL CAUSE SEVERE BURNS IF TOUCHED.
Before attempting to replace the lamp, make sure the television has completely run through its cooling cycle. Turn the power 
off and wait until the LAMP LED blinks very slowly and turns off completely. Unplug the TV. If you feel any warmth as you 
place your hand near the lamp, DO NOT TOUCH IT. Wait until the lamp has completely cooled before attempting to replace it. 
After turning the power off, wait at least 1 hour or more.
NEVER attempt to replace the lamp with the television plugged into a wall outlet. Attempting to replace the lamp with the TV 
plugged in could lead to a severe electrical shock.
Do not keep the TV on for more than 24 hours consecutively. There is the possibility of the life of the lamp being shortened.
The life of the lamp changes depending on the atmospheric temperature and altitude in which the TV is being used.
Please read these instructions fully before attempting to replace the lamp. If you feel unsure about replacing the lamp 
yourself, call a service technician.
LAMP NEEDS TO BE REPLACED. REFER TO 
OWNERS MANUAL FOR REPLACEMENT 
INSTRUCTIONS.
AFTER REPLACING THE LAMP, PLEASE RESET 
TIMER IN THE TV MENU.
PRESS OK, IF YOU DO NOT WANT TO SEE THIS 
MESSAGE AGAIN.
HD-Z70&56RX5_Eng.book  Page 30  Tuesday, October 11, 2005  9:17 PM
 
						

							Appendix
31
LT-Z70/56RX5 / LCT1911-001A / English
ENGLISH
How to Replace the Lamp
Please read these instructions fully before attempting to replace the 
lamp. If you feel unsure about replacing the lamp yourself, call a 
service technician. Please observe all safety warnings.
1 Turn off the television.
Press the POWER button on the remote control or TV front panel. 
Wait until the picture has closed and the LAMP LED on the front 
panel has stopped blinking indicating the lamp cool down is 
complete.
2 Unplug the television.
Disconnect the power cord from the AC outlet. Make sure that the 
LAMP LED light has stopped blinking before you unplug the set. 
Never attempt to replace the lamp with the television plugged in.
3 Remove the lamp cover.
The lamp is located behind the lamp cover on the left side of the 
television. To access the lamp you will need to remove the lamp 
cover. First, loosen the screw located on the lamp cover using your 
fingers. Once the screw has been loosened, gently pull the knob 
towards you and the panel will come away from the television. Set 
it aside.
4 Remove the lamp unit.
Using a Philips head type screwdriver (cross-head type), loosen 
the two screws fastening the lamp unit. When the screws have 
been loosened, remove the lamp by raising the handle and gently 
sliding the unit straight towards you. Place it carefully in the 
recycling packaging.
5 Install the new lamp unit.
Holding the handle attached to the new lamp unit, slide and push 
the new lamp straight into the television and back into the lamp 
housing area. Do not forget to re-tighten the two screws.
• Do not touch the lamp surface. Fingerprint or other stains may 
cause the unit to brake.
• If the lamp does not sit securely in the TV (flat in the lamp 
housing area), it won’t turn on. Make sure the lamp sits 
securely and flat in the housing area.
6 Re-install the lamp cover.
Insert the lamp cover in the rigit concaves and close the lamp 
cover. Because the lamp cover has a role to help prevent the 
danger of an electrical shock, tighten the screw using your fingers.
LAMP TIMER RESET
The lamp replacement message will appear when you need to change 
the lamp. After you replace the lamp, you need to reset the timer 
which is built into your television.
1 Choose LAMP TIMER RESET in the SET UP menu, then 
press the a or 3 button (see page 14)
The following message will appear.
2 Press a button while the above message appears on 
the television screen
The lamp timer has now been reset and the following message will 
blink.
• You can use the LAMP TIMER RESET only after replacing 
the lamp.
WARNING: The cool-down process cools the lamp from 
its operating temperature. This does not mean that the 
lamp will now be cool enough to handle safely. We 
strongly recommend you wait at least one hour before 
proceeding.
WARNING: DO NOT attempt to remove the assembly 
until the lamp has fully cooled. If you feel any heat near 
the lamp, STOP and wait until the lamp has FULLY 
COOLED.
NEVER attempt to remove the lamp with the television 
plugged into an outlet.
DO NOT DROP the used lamp. The inside of the lamp is 
under pressure. Dropping or other hard shocks could 
cause the lamp to shatter.
ALWAYS recycle the used lamp. Because the lamp 
contains a small amount of mercury, it cannot be thrown 
away with regular trash. Follow the recycling 
instructions included with the Lamp Replacement Kit.PRESS OK TO RESET THE LAMP TIMER.
THE LAMP TIMER IS RESET SUCCESSFULLY.
HD-Z70&56RX5_Eng.book  Page 31  Tuesday, October 11, 2005  9:17 PM
 
						

							LT-Z70/56RX5 / LCT1911-001A / English
32
ENGLISH
Specifications
We may change the design and specifications without notice.
Pictures displayed on the screen using this TV’s ZOOM functions should not be shown for any commercial or demonstration purpose in public 
places (cafes, hotels, etc.) without the consent of the owners of copyright of the original picture sources, as this would be an infringement of 
copyright.
ModelHD-Z70RX5HD-Z56RX5
Type HD-ILA Device Projection
Broadcasting systems B, G, I, D, K, K1, M
Colour systems PAL, SECAM, NTSC 3.58/4.43 MHz
Channels and frequencies VHF low channel (VL) = 46.25 to 168.25 MHz 
VHF high channel (VH) = 175.25 to 463.25 MHz 
UHF channel (U) = 471.25 to 863.25 MHz
• Receives cable channels in mid band (X to Z+2, S1 to S10), super band (S11 to 
S20) and hyper band (S21 to S41).
Sound-multiplex systems NICAM (B/G, I, D/K) system, A2 (B/G, D/K) system
Languages displayed by teletext  Please see the table in the description “TELETEXT LANGUAGE” on page 23.
Teletext systems FLOF (Fastext), WST (World Standard System)
Power requirements 110 - 240 V AC, 50/60 Hz
Power consumption 187 W (Standby: 2.5 W) 187 W (Standby: 2.5 W)
Projection Source 110W High-Pressure Mercury Lamp
Screen size Viewable area 178 cm (measured diagonally) Viewable area 142 cm (measured diagonally)
Audio output Rated Power output: 10 W + 10 W
Speakers 10 cm round × 2
VIDEO-1 terminal  RCA connector × 3, S VIDEO connector × 1, Component connector × 1
• Video input, S VIDEO (Y/C) input, Component video (Y, Cb/Pb, Cr/Pr) input and 
Audio L/R inputs are available.
• 480i (525i), 480p (525p), 576i (625i), 576p (625p), 1080i (1125i), 720p (750p) 
signals are available.
VIDEO-2 terminal RCA connector × 3, S VIDEO connector × 1
• Video input, S VIDEO (Y/C) input and Audio L/R inputs are available.
VIDEO-3 terminal  RCA connector × 3, Component connector × 1
• Video input, Component video (Y, Cb/Pb, Cr/Pr) input and Audio L/R inputs are 
available.
• 480i (525i), 480p (525p), 576i (625i), 576p (625p), 1080i (1125i), 720p (750p) 
signals are available.
VIDEO-4 terminal RCA connector × 3, S VIDEO connector × 1
• Video input, S VIDEO (Y/C) input and Audio L/R inputs are available.
DIGITAL IN terminal HDMI connector × 1, RCA connector × 2
• Digital video input , digital audio input and Audio L/R inputs are available. (Refer to 
page 28 for details.)
MONITOR OUT terminal RCA connectors × 3, S VIDEO connector × 1
• Video output, S VIDEO (Y/C) output and Audio L/R outputs are available.
• Output level 0.5 Vrms.
PC IN (D-SUB) terminal Analogue RGB D-SUB (15 pin) × 1
• PC signal is available. Refer to page 28 for details of the signals which can be 
input.
AV COMPULINK jack Stereo mini-jack (3.5 mm in diameter)
Headphone jack Stereo mini-jack (3.5 mm in diameter)
Dimensions (W × H × D) 1626 mm × 1167 mm × 519 mm 1318 mm × 968 mm × 439 mm
Weight 72 kg 42 kg
Accessories Remote control unit × 1 (RM-C1835)
AA/R6 dry cell battery × 2
HD-Z70&56RX5_Eng.book  Page 32  Tuesday, October 11, 2005  9:17 PM
 
						

							LT-Z70/56RX5 / LCT1911-001A / All Cover
Cover03
HD-Z70&56RX5_Eng.book  Page 1  Tuesday, October 11, 2005  9:17 PM
 
						

							LT-Z70/56RX5 / LCT1911-001A / All Cover
Cover04
1005TKH-MW-VP
Cover4.fm  Page 2  Friday, October 14, 2005  12:58 PM