JVC Av 2986me Instructions

17
Customized settingVNRYou can reduce the picture noise.Select VNR in PICTURE menu, then choose a setting of VNR function.OFF VNR is turned off.
AUTO Effect of VNR is automatically controlled.
MIN Effect of VNR becomes minimum level.
MAX Effect of VNR becomes maximum level.If you select MAX, the picture becomes softer even if the original 
picture is sharp.
When you select VIDEO-2, you cannot adjust VNR function.LANGUAGEYou can choose your desired on screen display language.Select LANGUAGE in the...

18Customized setting (continued)
DISPLAYYou can display the programme number, video terminal number 
and PR list on the screen.
Press the DISPLAY button to select the desired mode:
Choose a TV channel or a VIDEO terminal.1  Press the DISPLAY button to display the PR LIST.2  Select a programme number or video terminal by pressing the 
5/∞ button to move up/down on the programme number or press 
the 2/3 button to skip for each 7 programme numbers, then press 
MENU/OK button.
ON         OFF          PR...

19
To register the TV channels automatically 
(AUTO PROGRAM)You can register the TV channels into the TV’s channel list 
automatically.1  Display the INSTALL menu.2  Choose AUTO PROGRAM, then press the MENU/OK button.
  AUTO PROGRAM function starts, and the channels received are 
registered in the channel list (PR LIST) automatically.3  The EDIT menu appears.To edit the channel list Proceed to Step 3 of “To edit the channel list 
(PR LIST)” on page 20.
If a channel is not 
registeredProceed to Step 3 of...

20
To add in the new channel
(INSERT in the EDIT menu)You can add in new channels in the TV channel list as you like.
You need to fi nd the “CH/CC” number for the TV channel. Find the 
“CH/CC” number corresponding to the channel number of the TV 
channel from “CH/CC number list” on page 21.1  Display the INSTALL menu.2  Choose EDIT/MANUAL, then press the MENU/OK button. 
  EDIT menu appears.3  Choose the PR number for which you will register a new TV 
channel. When you add a new TV channel of NTSC-M...

21
TV channel presetting (continued)CH/CC numberWhen you want to use the INSERT function 
on page 20, find the CH/CC number 
corresponding to the channel number of the 
TV channel from this table.Channel No. Country
US United States, Philippines, etc..
CCIR
Middle East, Southeast Asia, etc..
OIRT Eastern Europe, Russia, Vietnam, 
etc..
AUSTRALIA Australia, etc..
Channel
CC US CCIR OIRT AUSTRALIA
CC 18 E S-18
CC 19 F S-19
CC 20 G S-20
CC 21 H S-21
CC 22 I S-22
CC 23 J S-23
CC 24 K S-24
CC 25 L S-25
CC 26...

22
V
L
R R L
/
MONO Y
C
BCR/
V
V SOVERL
R/
MONOOUTPUT VIDEO-1COMPONENT
(VIDEO-2)
INPUT INPUT
The illustrations shown in this section are for AV-21BS26 and AV-
29SS26 only, which are used for explanation purpose. Your TV may 
not look exactly the same as illustrated.
Before connecting
•  Read the manuals provided with the devices for the proper 
connection.
•  Turn off all the devices including the TV.
•  Note that connecting cables are not supplied.Connecting to front video input terminalsAdditional...

23
TroubleshootingIf a problem occurs when you are using the TV, check the below 
troubleshooting guide before calling for repair.
• Colour patches appear 
at the corner of the 
screen
• This may due to the magnetized device such as a 
speaker near to your TV. Keep the device apart from 
your TV. Alternately, you can also use the magnetic-
shielded speaker.
•  Picture is tilted
• This may due to the earth magnetism. Refer to 
“PICTURE TILT” on page 11 to correct the tilt.
•  Image takes a short 
period...

© 2006 Victor Company of Japan, Limited0406-FLE-JMTSpecifi cationsTV RF systems
  B, G, I, D, K, M
Colour systems
  PAL, SECAM, NTSC 3.58 MHz, NTSC 4.43 MHz
Receiving channels
  VHF low channel (VL), VHF high channel (VH), UHF channel (U)
  Receives cable channels in mid band, super band and hyper band.
Power requirements
  For Australia:   AC 220 to 240 V, 50 Hz / 60 Hz
  For others:   AC 110 to 240 V, 50 Hz / 60 Hz
External input / output
  VIDEO-1:  S-video input, VIDEO input, AUDIO L/R input...