InFocus ScreenPlay 7205 Projector User Manual

30
Tr a n s l u c e n t  O S D: makes the menus translucent. This prevents the 
image from being completely covered by the menus while you are 
making image adjustments.
Chime: turn this on to hear a sound when the Powe r button is pressed.
Sleep Timer: allows you to force the projector to automatically shutoff 
after 4 hours.
Pow e r  S av e: when On, the lamp is automatically turned off after no 
signals are detected for 20 minutes. After 10 additional minutes with no 
signal, the projector powers...

31
Service: to use these features, highlight them and press Select.
Factory Reset: restores all settings (except Lamp Hours) to their default 
after displaying a confirmation dialog box.
Te s t  P a t t e r n: displays a test pattern when the Blank button on the remote is 
pressed. To select the patterns, use the up/down arrows on the remote or 
keypad. Press the remote’s Blank button to exit test pattern mode.
Blue Only: turns off the Red and Green portions of the input, allowing you 
to properly adjust...

32
Replacing the projection lampThe lamp hour timer in the About menu counts the number of hours the 
lamp has been in use. Twenty hours before the lamp life expires, the mes-
sage “Change lamp” appears on the screen at startup. If the maximum lamp 
time is exceeded, the lamp will not light. In this case, after replacing the 
lamp you must reset the lamp hours by simultaneously pressing both 
Brightness buttons on the keypad and holding them for 10 seconds. You 
can order new lamp modules from your...

33
WARNINGS: 
 To avoid burns, allow the projector to cool for at least 60 minutes before 
you replace the lamp.
 Do not drop the lamp module. The glass may shatter and cause injury.
 Do not touch the glass lamp screen. Fingerprints can obscure projection 
sharpness.
 Be extremely careful when removing the lamp module. In the unlikely 
event of the lamp rupturing, discard any edible items placed in the sur-
rounding area and thoroughly clean the area along all sides of the pro-
jector. Wash hands...

34
AppendixRed LED behavior and projector errorsIf the projector is not functioning properly and the red LED is blinking, con-
sult Ta b l e  2 to determine a possible cause. There are two second pauses 
between the blinking cycles. Visit www.infocushome.com/support for 
more details on the red LED error codes.
Projected image sizeNOTE: Visit our website at www.infocushome.com/support for an interac-
tive image size calculator.
Table 3: Red LEDs
Red LED Behavior Explanation
One (1) blink The lamp wont...

35
Source compatibility
Table 5: 
Source Compatibility
Video Component and RGB HDTV (720p, 1035i, 1080p, 1080p-24Hz)
DVI/HDCP for digital video and encrypted digital video
Component EDTV (480p, 576p progressive scan), 
SECAM: M, Component, Composite and S-Video standard 
video (480i, 576i, 576i RGB SCART with adapter, 
NTSC, NTSC M 4.43, 
PAL: B, H, I, M, N)
Computer Digital and analog PC, Macintosh, 1280x1024 resolution 
Communi-
cationUSB and RS-232
Table 6: 
Projector Inputs and Outputs
2-Component...

36
Projector dimensions for ceiling mount installations
11.3”
288.1mm2.6”
64.9mm2.3”
57.8mm2.1”
53.7mm
12.3”
312.7mm
total length with optional cable cover: 16.2” 411.5mm) dimensions of optional cable cover: 12.4 x 3.9 x 3.2” (315 x 100 x 82mm)
8.5”
216mm 8.7”
221.4mm
4.3”
109.5mm
0.14”
3.6mm 

37
RS-232 terminal specificationsCommunication configurationTo control the projector from an LCD control panel, connect an RS-232 cable 
to the serial control connector on the projector and set your computer ’s 
serial port settings to match this communication configuration:Command formatAll commands consist of 3 alpha characters followed by a request, all 
enclosed in parentheses. The request can be a read request (indicated by a 
“?”) or a write request (indicated by 1 to 4 ASCII digits).
A read...

38 Supported commands
Function Command Range Default
Aspect Ratio ARZ 0-4
0 = Native
1 = 16:9
2 = 4:3
3 = Letterbox
4 = Natural Wide1
Auto Chime Enable ACE 0-1 1
Auto Power APO 0-1 0
Auto Source ASC 0-1 0
Blank BLK 0-1 0
Blank Screen BSC 0-2
0 = black
1 = blue
2 = white0
Blue Color Offset BCO 1-63 32
Blue Gain BCG 1-63 32
Brightness BRT 2-254 128
Ceiling CEL 0-1 0
Chroma Detail CDE 0-20 0
Color CLR 2-254 128
Color Space CSM 0-7
0 = RGB
3 = REC601
2 = REC709
7 = Auto7
Color Temp TMP 0-2
0 = 9300
1 = 8200...

39
Language LAN 0-11
0 = English
1 = French
2 = German
3 = Spanish
4 = Chinese Tradi-
tional
5 = Japanese
6 = Korean
7 = Portuguese
8 = Russian
9 = Norwegian
10 = Chinese Sim-
plified
11 = Italian0
NTSC 2:2 Pulldown Enable NPE 0-1 0
Noise Reduction Enable NRE 0-2
0 = Off
1 = Auto
2 = Manual0
Noise Reduction Level NRL 0-10 5
Overscan OVS 127=Crop
128=Off
129=Zoom128
Phase MSS 0-31 n/a
Power PWR 0-1 0
Power Save PSV 0-1 1
Presets PST 0-2
0 = User 1
1 = User 2
2 = User 30
Rear Project REA 0-1 0
Red Color...