InFocus ScreenPlay 7205 Projector User Manual

20
Using the keypad buttonsMost buttons are described in detail in other sections, but here is an over-
view of their functions:
Pow e r–turns the projector on (page 9) and off (page 9).
Menu–opens the on-screen menus (page 23).
Select–confirms choices made in the menus (page 23).
Up/down arrows–navigates to and adjusts settings in the menus (page 23).
Auto image–resets the projector to the source.
Presets–cycles through the 3 available user preset settings (page 26).
Key s t o n e–adjusts squareness of...

21
Using the remote controlThe remote uses two (2) provided AAA batteries. They are easily installed 
by sliding the cover off the remote’s back, aligning the + and - ends of the 
batteries, sliding them into place, and then replacing the cover.
To operate, point the remote at the projection screen or at the projector (not 
at the video device or computer). The range of optimum operation is up to 
30 feet (9.14m).
Press the remote’s Menu button to open the projector ’s menu system. Use 
the arrow buttons...

22
Optimizing video imagesAfter the video device is connected properly and the image is on the screen, 
you can optimize the image using the onscreen menus. For general informa-
tion on using the menus, see page 23.
 Change the Aspect ratio. Aspect ratio is the ratio of the image width to 
image height. TV screens are usually 1.33:1, also known as 4:3. HDTV 
and most DVDs are 1.78:1, or 16:9. Choose the option that best fits your 
input source in the menus, or press the Resize button on the remote to...

23
Using the menusTo open the menus, press the menu button on the keypad or remote. (The 
menus automatically close after 60 seconds if no buttons are pressed.) The 
Main menu appears. Use the arrow buttons to move up and down to high-
light the desired submenu, then press the Select button. 
To change a menu setting, highlight it, press Select, then use the up and 
down arrow buttons to adjust the value, select an option using radio but-
tons, or turn the feature on or off using check boxes. Press...

24
Picture menuTo adjust the following five settings, highlight the setting, press Select, use 
the up and down arrows to adjust the values, then press select to confirm 
the changes. All menu defaults are listed in a table starting on page 38.
Key s t o n e: adjusts the image vertically and horizontally to make a squarer 
image. The two keystones ranges are interdependent. The combined num-
ber of steps for both is 50. If one keystone is set to 65, it is 15 steps above the 
center position of 50. This...

25
16:9: the default is 16:9, which preserves the 16:9 aspect ratio and is 
designed to be used with content that is Enhanced for Widescreen TVs. 
4:3: resizes the image from its original version to fit a standard 4:3 
aspect ratio screen. If you have a 4:3 source on a 16:9 screen, the image 
is placed in a 16:9 space, so black bars appear at the sides of the image.
Letterbox: preserves the 16:9 aspect ratio. If you have a 16:9 source and 
screen, the image fills the screen. If your source is...

26
Presets: This allows you to customize settings and save the settings to be 
restored later. To restore the factory default settings, choose Factory Reset in 
the Settings>Service menu. 
To set a preset for the current source, adjust the image, select Save Settings 
in the Presets menu, then choose Save User 1, 2, or 3. You can recall these 
settings in the future by selecting the appropriate user presets. 
Gamma: Gamma tables contain preset intensity configurations optimized 
for the input source. You...

27 Advanced settings
The following 4 options are for computer or HDTV sources only. 
Phase: adjusts the phase of the video signal’s digital conversion.
Tr a c k i n g: adjusts the frequency of the video signal’s digital conversion. 
Horizontal/Vertical Position: adjusts the position of the source.
Sync Threshold Adjust: If a hardware device, such as a DVD player, is not 
syncing properly with the projector, select this option to help it to sync 
when connected to the projector. 
Tr u e L i f e: This...

28
Color Space: This option applies to computer and HDTV sources (it won’t 
appear in the menu for video sources). It allows you to select a color space 
that has been specifically tuned for the video input. When Auto is selected, 
the projector automatically determines the standard. To choose a different 
setting, turn off Auto, then choose RGB for computer sources, choose 
REC709 for component 1080i or 720p sources, or choose REC601 for compo-
nent 480p or 576p sources.
Color Temperature: changes the...

29
Settings menuSources
: allows you to assign a particular input to a specific source key on 
the remote and enables or disables Autosource. When Autosource is not 
checked, the projector defaults to the last-used source. If no source is found, 
a blank screen displays. When Autosource is checked, the projector checks 
the last-used source first at power up. If no signal is present, the projector 
checks the sources in order until a source is found or until power down. 
You can use the Source Enable...