InFocus Projector X16 User Manual

Operation 31
3D Color Management
In most installation situations, color management will not be necessary, such as in 
classroom, meeting room, or lounge room situations where lights remain on, or 
where building external windows allow daylight into the room. 
Only in permanent installations with controlled lighting levels such as boardrooms, 
lecture theaters, or home theaters, should color management be considered. 3D 
Color Management provides fine color control adjustment to allow for more 
accurate...

Operation 329. Press MENU/EXIT to exit and save the settings.
Saturation is the amount of that color in a video picture. Lower settings produce less 
saturated colors; a setting of “0” removes that color from the image entirely. If the saturation 
is too high, that color will be overpowering and unrealistic.
Setting the presentation timer
The presentation timer can indicate the presentation time on the screen to help you 
achieve better time management when giving presentations. Follow these steps to...

Operation 33
To cancel the timer, perform the following steps.
1. Enter the SYSTEM SETUP: Basic > Presentation Timer menu and highlight 
Off. Press MODE/ENTER. A confirmation message displays.
2. Highlight Yes and press MODE/ENTER to confirm. You will see the message 
“Timer is Off” displaying on the screen. 
Hiding the image
In order to draw the audiences full attention to 
the presenter, you can use BLANK on the 
projector or remote control to hide the screen 
image. Press any key on the projector or...

Operation 34
Freezing the image
Press   on the remote control to freeze the 
image. The word FREEZE will display in the 
upper left corner of the screen. To release the 
function, press any key on the projector or 
remote control.
Even if an image is frozen on the screen, the 
pictures are running on the video or other 
device. If the connected devices have active 
audio output, you will still hear the audio even though the image is frozen on 
screen.
Operating in a high altitude environment
We recommend...

Operation 35
Adjusting the sound level
To adjust the sound level:
1. Repeat steps 1-2 above.
2. Press  to highlight Volume and press  /  to select a desired sound level.
Personalizing the projector menu display
The On-Screen Display (OSD) menus can be set according to your preferences. 
The following settings do not affect the projection settings, operation, or 
performance. 
•Menu display time in the SYSTEM SETUP: Advanced > Menu Settings 
menu sets the length of time the OSD will remain active after...

Operation 36
Menu operation
Menu system
Please note that the on-screen display (OSD) menus vary according to the signal 
type selected.
The menu items are available when the projector detects at least one valid signal. If 
there is no equipment connected to the projector or no signal detected, limited 
menu items are accessible.
Main menu Sub-menu Options
1. 
DISPLAY
Wall ColorOff/Light Yellow/Pink/Light 
Green/Blue/Blackboard
Aspect Ratio Auto/Real/4:3/16:9
Keystone
Position
Phase
H. Size
Digital Zoom...

Operation 37
4. 
SYSTEM 
SETUP: 
Basic
Language
Projector PositionFront Table/Rear Table/Rear 
Ceiling/Front Ceiling
Auto Power OffDisable/5 min/10 min/15 min/20 
min/25 min/30 min
Blank TimerDisable/5 min/10 min/15 min/20 
min/25 min/30 min
Panel Key Lock On/Off
Timer ControllerDisable/30 min/1 hr/2 hr/3 hr/4 
hr/8 hr/12 hr
Splash ScreenBlack/Blue/InFocus
5. 
SYSTEM 
SETUP: 
Advanced
Quick Cooling On/Off
High Altitude Mode On/Off
Audio SettingsMute On/Off
Volume
Menu SettingsMenu display 
time5 sec/10...

Operation 38
Description of each menu
FUNCTION
(default setting/
value)DESCRIPTION (default setting/value)
Wall Color
 (Off)Corrects the projected picture’s color when the projection 
surface is not white. See Using Wall Color on page 29 for 
details.
Aspect Ratio
(Auto)There are four options to set the images aspect ratio 
depending on your input signal source. See Selecting the 
aspect ratio on page 26 for details.
Keystone
(0)Corrects any keystoning of the image. See Correcting 
keystone on page 25...

Operation 39
FUNCTION
(default setting/
value)DESCRIPTION (default setting/value)
Tint
(0)Adjusts the red and green color tones of the image. See 
Adjusting Tint on page 30 for details.The function is only available when Video or S-Video with NTSC 
system is selected.
Sharpness
(15)Adjusts the image to make it look sharper or softer. See 
Adjusting Sharpness on page 30 for details.
Brilliant 
Color
(On)Adjusts white peaking while maintaining correct color 
presentation. See Adjusting Brilliant Color on...

Operation 40
FUNCTION
(default setting/
value)DESCRIPTION (default setting/value)
Blank Timer
(Disable)Sets the image blank time when the Blank feature is activated, 
once elapsed the image will return to the screen. See Hiding 
the image on page 33 for details.
Panel Key 
Lock
(Off)Disables or enables all panel key functions except POWER 
on the projector and keys on the remote control. See Locking 
control keys on page 33 for details.
Timer 
Controller
(Disable)Sets the auto-shutdown timer. The timer...