Home > InFocus > Projector > InFocus Projector X16 User Manual

InFocus Projector X16 User Manual

Here you can view all the pages of manual InFocus Projector X16 User Manual. The InFocus manuals for Projector are available online for free. You can easily download all the documents as PDF.

Page 21

Operation 21
Utilizing the password function
For security purposes and to help prevent unauthorized use, the projector includes 
an option for setting up password security. The password can be set through the 
On-Screen Display (OSD) menu. For details of the OSD menu operation, please 
refer to Using the menus on page 20.
You will be inconvenienced if you activate the password functionality and subsequently forget 
the password. Print this reference guide (if necessary) and write the password you used in...

Page 22

Operation 22
Entering the password recall procedure
1. Press and hold AUTO on the projector or 
remote control for 3 seconds. The projector 
will display a coded number on the screen.
2. Write down the number and turn off your 
projector.
3. Seek help from the local service center to 
decode the number. You may be required to 
provide proof of purchase documentation to 
verify that you are an authorized user of the 
projector.
Changing the password
1. Open the OSD menu and go to the SYSTEM SETUP:...

Page 23

Operation 23 your retry. You can press MENU/EXIT to cancel the change or try 
another password.
Though the password function is disabled, you need to keep the old password in hand should 
you ever need to re-activate the password function by entering the old password.
Switching input signal
The projector can be connected to multiple devices at the same time. However, it 
can only display one full screen at a time. 
Be sure the Quick Auto Search function in the SOURCE menu is On (which is the 
default of...

Page 24

Operation 24
Adjusting the projected image
Adjusting the projection angle
The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster 
foot. These adjusters change the image height and projection angle. To adjust the 
projector:
1. Press the quick-release button and lift the 
front of the projector. Once the image is 
positioned where you want it, release the 
quick-release button to lock the foot in 
position.
2. Screw the rear adjuster foot to fine tune 
the horizontal angle.
To...

Page 25

Operation 25
Fine-tuning the image size and clarity
1. Adjust the projected image to the size that 
you need using the zoom ring.
2. Then sharpen the image by rotating the focus 
ring.
Correcting keystone
Keystoning refers to the situation where the projected image is noticeably wider at 
either the top or bottom. It occurs when the projector is not perpendicular to the 
screen. 
To correct this, besides adjusting the height of the projector, you will need to 
manually correct it following one of these...

Page 26

Operation 26
Magnifying and searching for details
If you need to find the details on the projected picture, magnify the picture. Use the 
direction arrow keys for navigating the picture.
• Using the remote control
1. Press Digital Zoom +/- to display the 
Zoom bar.
2. Press Digital Zoom + to magnify the 
center of the picture. Press the key 
repeatedly until the picture size is suitable 
for your need.
3. Use the directional arrows ( ,  ,  ,  ) 
on the projector or remote control to 
navigate the...

Page 27

Operation 27 3. Press  /  to select an aspect ratio to suit the format of the video signal and 
your display requirements.
About the aspect ratio
In the pictures below, the black portions are inactive areas and the white portions are active 
areas. OSD menus can be displayed on those unused black areas.
1.Auto: Scales an image proportionally to fit the 
projectors native resolution in its horizontal 
width. This is suitable for the incoming image 
which is neither in 4:3 nor 16:9 and you want to 
make...

Page 28

Operation 28
Optimizing the image
Selecting a picture mode
The projector is preset with several 
predefined picture modes so that you can 
choose one to suit your operating 
environment and input signal picture type.
To select a operation mode that suits your 
need, you can follow one of the following 
steps.
• Press MODE/ENTER on the remote 
control or projector repeatedly until your desired mode is selected.
• Go to the PICTURE > Preset Mode menu and press  /  to select a desired 
mode.
Picture modes...

Page 29

Operation 29
Setting the User 1/User 2 mode
There are two user-definable modes if the current available picture modes are not 
suitable for your need. You can use one of the picture modes (except the User 1/
User 2) as a starting point and customize the settings.
1. Press MENU/EXIT to open the On-Screen Display (OSD) menu.
2. Go to the PICTURE > Preset Mode menu.
3. Press /  to select User 1 to User 2.
4. Press  to highlight Reference Mode.
This function is only available when User 1, or User 2 mode is...

Page 30

Operation 30
Adjusting Color
Highlight Color in the PICTURE menu and adjust the values by pressing  / on 
the projector or remote control.
Lower setting produces less saturated colors. If the setting is too high, colors on the 
image will be overpowering, which makes the image unrealistic.
Adjusting Tint
Highlight Tint in the PICTURE menu and adjust the values by pressing  / on 
the projector or remote control.
The higher the value, the more reddish the picture becomes. The lower the value, 
the more...
Start reading InFocus Projector X16 User Manual

Related Manuals for InFocus Projector X16 User Manual

All InFocus manuals