InFocus Projector Screenplay 5000 User Manual

29
Sleep Timer: allows you to force the projector to automatically shutoff after 
4 hours.
Screen Save: automatically blanks the screen with a black color after no sig-
nals are detected for a preset number of minutes. The image returns when 
an active source is detected or a remote or keypad button is pressed. Screen 
Save is disabled when Power Save is enabled.
Startup Logo: allows you to display a blank Black, White, or Blue screen 
instead of the default screen at startup and when no source is...

30
Language: allows you to select a language for the onscreen display of 
menus and messages.
Service: to use these features, highlight them and press Select.
Factory Reset: restores all settings (except Lamp Hours) to their default 
after displaying a confirmation dialog box.
Lamp Reset: resets the lamp hours counter in the About menu to zero. Do 
this only after changing the lamp. It displays a confirmation dialog box.
Service Info: provides information about the projector ’s software version 
and the...

31
MaintenanceCleaning the lens1
Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
Avoid using an excessive amount of cleaner, and don’t apply the 
cleaner directly to the lens. Abrasive cleaners, solvents or other harsh 
chemicals might scratch the lens.
2
Lightly wipe the cleaning cloth over the lens in a circular motion. If you 
don’t intend to use the projector immediately, replace the lens cap.
clean the lens 
with a soft dry cloth
and non-abrasive
cleaner 

32
Replacing the projection lampThe lamp hour timer in the About menu counts the number of hours the 
lamp has been in use. When the lamp timer reaches the estimated total lamp 
life, the LED on the projector ’s keypad blinks red (indicating a lamp error, 
see page 36) and a dialog box appears each time the projector is turned on. 
You can order new lamp modules from your dealer. See “Accessories” on 
page 35 for information.1
Turn off the projector and unplug the power cable. 
2
Wait 60 minutes to allow...

33
 Be extremely careful when removing the lamp housing. In the unlikely 
event that the lamp ruptures, small glass fragments may be generated. 
The lamp module is designed to contain most of these fragments, but 
use caution when removing it. Before replacing the lamp, clean the 
lamp compartment and dispose of cleaning materials. Wash hands after 
lamp replacement. This product has a lamp which contains a very 
small amount of mercury. Dispose of it as required by local, state or fed-
eral ordinances...

34
Cleaning the dust filtersIn dirty or dusty environments, the dust filters can become clogged, causing 
high temperatures inside the lamp module. These high temperatures can 
impact lamp performance and operating life. Routine maintenance to 
remove dust and dirt from the filters lowers the lamp operating tempera-
ture and prolongs lamp life. To maximize lamp life you will need to clean 
the filters every 250 hours. Lamp filter maintenance may need to occur more 
often than 250 hours depending on your...

35
AppendixAccessoriesNOTE: Use only approved accessories. Standard Accessories
(ship with the projector)
Part Number
Computer Cable 6 ft (1.8 m) 210-0185-xx
Audio/Video Cable 6 ft (1.8 m) 210-0053-xx
S-video Cable 210-0125-xx
Power Cable, US*  210-0023-xx
Power Cable, EURO*  210-0029-xx
Director Remote 590-0567-xx
Projection Lamp Module (included 
in projector)SP-LAMP-017
Lens Cap 340-1234-xx
Lens Cap Tether 321-0192-xx
Quick Setup card 009-0931-xx
User’s Guide 010-0555-xx
Safety Card 009-0659-xx
SCART...

36
Red LED behavior and projector errorsIf the projector is not functioning properly and the red LED is blinking, con-
sult Ta b l e  2 to determine a possible cause. There are two second pauses 
between the blinking cycles. Visit our website for more details on the red 
LED error codes. See the inside back cover for contact information.
Projected image sizeNOTE: Visit our website for an interactive image size calculator.
Table 3: 
Red LED Behavior Explanation
One (1) blink The lamp wont strike after...

37
Index
A
audio 21
audio volume 10
Auto Power 28
B
Blank screen 29
blinking green 12
blinking red 12
C
cable box 7
cables
optional 35
standard 35
cleaning the dust filter 34
cleaning the lens 31
Color 10
Color Control 27
colors are incorrect 17
component cable connector 8
composite video connector 8
computer image
troubleshooting 13
connecting
power cable 8
connector panel 5
contacting InFocus 18
Contrast 10
custom logo
startup screen 29
customer service contact information 18
D
Display Messages...

38
blinking red 17
solid green 12
solid red 18
LED behavior 12
lens, cleaning 31
Letterbox 25
lock, security 34
M
Main menu 23
menu system 23
N
Natural Wide 25
no computer image 14
no startup screen 13
O
offset 6
only startup screen appears 13
optional accessories 35
Overscan 26
P
Picture in Picture 29
Picture menu 24
PiP 29
power cable 8, 11
Power Save 28
projected image sizes 36
projection distance 6
projector
adjusting the height 9
connector panel 5
customizing 22
optional accessories 35
remote...