InFocus Projector Screenplay 5000 User Manual

9
Displaying a video imageRemove the lens cap. 
Press the Pow e r button on the top of the projector or the remote.
The fans start to run. When the lamp comes on, the startup screen is dis-
played. It can take a minute for the image to achieve full brightness. 
? No startup screen? Get help on page 12.
Plug in and turn on the video device.
The video device’s image should appear on the projection screen. If it 
doesn’t, press the Source button on the keypad or remote. 
Adjust the height of the projector...

10
Adjust the zoom or focus rings by rotating them until the desired image size 
and focus are produced.
If the image is not square, adjust the vertical keystone using the buttons on 
the keypad. 
Press the upper Ke y s t o n e  button to reduce the upper part of the image, and 
press the lower Ke y s t o n e  button to reduce the lower part.
You can also adjust the horizontal keystone via the menus, or set the projec-
tor to automatically adjust the vertical keystone. See page 24.
Adjust the volume in...

11
Connecting a computerConnect either a VESA cable or M1 cable into the appropriate connector on 
the projector (Ve s a  1  o r  DV I  2). Connect the other end to the video port on 
your computer. If you are using a desktop computer, you first need to dis-
connect the monitor cable from the computer ’s video port. 
Connect the black power cable to the connector on the back of the projector 
and to your electrical outlet. The Power LED on the projector ’s keypad 
turns solid green.
NOTE: Always use the...

12
Shutting down the projectorThe projector automatically blanks the screen after no active source is 
detected for 30 minutes. This blank screen helps preserve the life of the pro-
jector. The image returns when an active source is detected or a remote or 
keypad button is pressed.
Screen Save
You can make the blank screen appear after five minutes by turning on 
Screen Save in the Settings>System menu. See page 29. There are six time 
options for the Screen Save feature. They range from five minutes to...

13
Source Troubleshooting
Problem Solution Result
No startup screenPlug power cable in, press Power button. 
Remove lens cap.Correct image
Only startup screen appears
Press the Source button 
Activate laptop’s external portComputer image projected
v
e
sa
1
L
a
u
d
io
in
c
o
m
p
o
n
e
n
t
3
s
e
r
ia
lc
o
n
t
r
o
l
d
v
12
v
i
d
e
o5t
r
ig
g
e
r
R
S
-
v
i
d
e
o4
v
e
s
a
1
L
a
u
d
io
in
component 3
s
e
ria
l
c
o
n
tro
l
d
v
1
2
v
id
e
o
5trig
g
e
r
R
S
-v
id
e
o
4
v
e
sa
1
L
a
u
d
i
o
in
c
o
m
p
o
n
e
n
t
3...

14
No computer image, just the words “Signal out of 
range” Adjust computer refresh rate in Control 
Panel>Display>Settings>Advanced>
Adapter (location varies by operating 
system)Computer image projected
Edges of image distortedTurn Overscan on in the Picture>Overscan 
menuCorrect image
vesa1
L
audioin
c
o
m
p
o
n
e
n
t
3
serialcontroldv12
video5trigger
R
S-video4
A
Signal out of
range
You may also need to set a different 
resolution on your computer.
vesa 1
L
audio in
c
o
m
p
o
n
e
n
t
3
serial...

15
Projector troubleshooting
Problem Solution Result
Image not square Adjust keystone on keypad or Picture menuSquare image
Image not sharpAdjust the focus lens or Sharpness in the 
Picture>Advanced menuCorrect image
Image does not fit 16:9 screenChange aspect ratio to 16:9 in 
Picture>Aspect ratio menu
Correct image
v
e
s
a
1
L
a
u
d
i
o
inc
o
m
p
o
n
e
n
t
3
s
e
r
i
a
l
c
o
n
t
r
o
ld
v
1
2
v
i
d
e
o
5t
r
i
g
g
e
r
R
S
-
v
i
d
e
o
4
ABAB
AB 

16
Image upside downTurn off Ceiling in Settings>System menu
Correct image
Image reversed left to rightTurn off Rear in Settings>System menu
Correct image 
A
B
AB
A
AB 

17
1. Projected colors don’t match source
2. Colors are washed out or too deep
3. Image from component source appears greenish1. Adjust color, tint, color temperature, 
brightness, or contrast in the menus.
2. Select another gamma setting
3. Select another color space
Correct image
Lamp won’t turn on, LED blinking red (page 12)Make sure vents aren’t blocked; allow 
projector to cool for one minute Unplug projector; wait one minute; plug in 
projector and turn it on: lamp lights
COLOR
COLOR
blinks
red
v...

18 Still having problems?
If you need assistance, visit our website or call us. See the inside of the back 
cover for a list of all relevant web addresses. This product is backed by a 
limited warranty. An extended warranty plan may be purchased from your dealer. When sending the projector in for repair, we recommend shipping 
the unit in its original packing material, or having a professional packaging 
company pack the unit. Please insure your shipment for its full value. Lamp won’t turn on, LED...