InFocus Projector Play Big In82 User Manual

							20
Picture menuTo adjust the following settings, highlight the setting, press Select, use the up and 
down arrows to adjust the values, then press Select to confirm the changes.Ke y s t o n e: adjusts the image vertically and makes a squarer image. Tilt the projec
-
tor up or down to adjust for keystone before using the digital keystone correction 
in the menu.Image Shift: moves the image vertically. Use to shift the image, or to mask arti
-
facts or bars on the top or bottom of the image.Contrast: controls the degree of difference between the lightest and darkest 
parts of the picture.Brightness: changes the intensity of the image.Color: adjusts a video image from black and white to fully saturated color. Tint: adjusts the red-green color balance in the image of NTSC video images. The 
tint setting applies to NTSC video sources only.Auto Image: resynchs the projector to the source.Aspect Ratio: Aspect ratio is the ratio of the image width to image height. HDTV 
and most DVDs are 16:9. TV screens are usually 4:3. The projector’s default is 
16:9. See 
“Choosing the aspect ratio” on page
 6 for more information.
Select Native to see the unmodified input with no resizing by the projector.
 
Select 16:9 to watch enhanced widescreen DVDs. Select Letterbox to preserve the 
16:9 aspect ratio. If you have a 16:9 source and screen, the image fills the screen. If 
your source is letterboxed, the image is expanded to fill the screen. Select Natural 
Wide to stretch a 4:3 image to fill the entire 16:9 screen. The center two-thirds of 
the image is unchanged; the edges of the image are stretched. For more informa
-
tion regarding Aspect Ratio, see 
page
 6.
Picture menu
increasing keystonedecreasing keystone
Aspect ratio
K1 RG.fm  Page 20  Thursday, September 27, 2007  10:24 AM 
						

							21
Presets: This allows you to customize settings and save the settings to be 
restored later. To restore the factory default settings, choose Factory Reset in the 
Settings>Service menu. To set a preset for the current source, adjust the image, select Save Settings in 
the Presets menu, then choose Save User 1, 2, or 3. You can recall these settings in 
the future by selecting the appropriate user presets. All settings in the Picture 
menu (except Keystone) are saved and recalled. ISF Day and ISF Night settings 
support certified Imaging Science Inc. calibration. ISF presets are not available until 
after calibration is performed, and picture settings cannot be adjusted when ISF 
presets are active. For more information go to www.infocus.com/service.BrilliantColor™: produces an expanded on-screen color spectrum that delivers 
enhanced color saturation for bright, true-to-life images. This feature is off by 
default.Gamma: Gamma tables contain preset intensity configurations optimized for the 
input source. You can select a gamma table that has been specifically tuned for 
either film, CRT (Cathode Ray Tube), video, PC, or Bright Room input. (Film input 
is material originally captured on a film camera, like a movie; video input is material 
originally captured on a video camera, like a TV show or sporting event.) NOTE: Your viewing preferences may vary. Cycle through the gamma options and 
pick the one you like the best.Overscan: removes noise around the edges of the video image. Select Zoom to 
remove the outer 3% of the image and scale the image back up to its original size. 
Select Crop to remove the outer 3% of the image without rescaling the image.
PresetsSave
User 
SettingsGammaOverscan
K1 RG.fm  Page 21  Thursday, September 27, 2007  10:24 AM 
						

							22
Advanced menuRemember that not all options in the menus are available for all sources/signals. Iris: adjusts the aperture of the iris from 0 to 100 (fully open) to regulate the 
amount of light emitting from the projector. Close the aperture to increase the 
contrast in dark images.Phase: adjusts the horizontal phase of a computer source.Tr a c k i n g: adjusts the vertical scan of a computer source.Horizontal/Vertical Position: adjusts the position of a computer source.Sync Threshold Adjust: (progressive signals only) If a hardware device, such as a 
DVD player, is not syncing properly with the projector, adjust this option to help it 
to sync when connected to the projector. Flesh Tone Correction: this modifies colors to make the skin complexion bet
-
ter.Black Level Calibration: Automatically adjusts brightness to get the best black 
level. Before using, make sure there are black bars at the top, bottom, or sides of 
the image.Film Mode: controls deinterlacing and is On by default. When checked, it 
assumes the incoming signal is film material and optimizes the image accordingly. Sharpness: (video sources only) changes the clarity of the edges of a video image. 
Select a sharpness setting.Color Space: This option applies to computer and component video sources. It 
allows you to select a color space that has been specifically tuned for the input sig
-
nal. When Auto is selected, the projector automatically determines the standard. 
To choose a different setting, turn off Auto, then choose RGB for computer 
sources, choose either REC709 or REC601 for component video sources.
Advanced menu
Sharpness Color Space
K1 RG.fm  Page 22  Thursday, September 27, 2007  10:24 AM 
						

							23
Color Temperature: changes the intensity of the colors. Select a value. Native 
means an uncorrected/unchanged color temperature. Other values change the 
white point of the colors. 6500K (the default setting) is generally used for film con
-
tent and 9300K is used for TV video.Color Gamut: sets the total number of possible displayable colors (gamut). 
Choose Auto to have the projector select automatically based on the current sig
-
nal format. Choose Maximum to display all colors that the projector is capable of 
displaying.Color Control: allows you to individually adjust the gain and offset of the red, 
green, and blue colors. These advanced controls have the same effect as contrast 
and brightness, but each controls a single color only.Video Standard: when it is set to Auto, the projector attempts to automatically 
pick the video standard based on the input signal it receives. (The video standard 
options may vary depending on your region of the world.) If the projector is unable 
to detect the correct standard, the colors may not look right or the image may 
appear “torn.” If this happens, manually select a video standard by selecting NTSC, 
PAL, or SECAM from the Video Standard menu.Noise Reduction: adjusts signal noise reduction. Choose Enable then adjust the 
level. The software determines the differences between successive image frames 
and averages the changes out to reduce the noise.
Color 
TemperatureColor Control
Video StandardNoise Reduction
K1 RG.fm  Page 23  Thursday, September 27, 2007  10:24 AM 
						

							24
Settings menuSources: 
allows programming of source buttons, enables autosource, and enables 
the SCART RGB source. When Autosource is selected, the Source Enable fea
-
ture indicates which sources the projector attempts to lock onto. You can use the 
Source Enable feature to eliminate certain sources from this search, which will 
speed the search. By default, the check boxes for all sources are checked except 
SCART RGB. Uncheck a source box to eliminate it from the search. When Auto
-
source is not checked, the projector defaults to Component initially, then defaults 
to whatever the last active source was when the projector was powered down. To 
display another source, you must manually select one by pressing the Source but
-
ton on the remote. This cycles through all the sources that are selected in the 
Source Enable menu. The Source 1, 2, and 3 menus in the Sources menu allow you to assign a source to 
the Source 1, 2, and 3 buttons on the remote. The Source 4 menu selection would 
apply to the Custom key if that option is chosen in the Custom key menu, see page
 25. To use the SCART RGB source, you must first select it in the Source 
Enable menu (the projector cannot automatically detect this source). Enabling 
SCART will disable Component and Composite sources.System>OSD Offset: allows you to adjust the position of the OSD. By default, 
the menus are postponed in the upper lefthand corner of the displayed image and 
the messages are postponed in the lower lefthand corner. Adjust the offset to 
move these items more to the right and middle of the display. Rear: reverses the 
image so you can project from behind a translucent screen. Ceiling: turns the 
image upside down for ceiling-mounted projection. Auto Ceiling: uses an internal 
sensor to automatically turn on ceiling mount mode if the projector is inverted. 
High Power: maximizes the light output of the lamp. Auto Power: When Auto 
Power is checked, the projector automatically goes into the startup state after the 
projector receives power. This allows control of ceiling mounted projectors with a 
wall power switch. 
Settings menu
SourcesSource
Enable
System menu
K1 RG.fm  Page 24  Thursday, September 27, 2007  10:24 AM 
						

							25
Display Messages: displays status messages (such as “Searching”) in the lower-
left corner of the screen.Tr a n s l u c e n t  O S D  (On Screen Display): makes the 
menus translucent. This prevents the image from being completely covered by the 
menus while you are making image adjustments. Sleep Timer: automatically turns 
off the projector after 4 hours. Pow e r  S av e: automatically turns the lamp off after 
no signals are detected for 20 minutes. After 10 additional minutes with no signal, 
the projector powers down. If an active signal is received before the projector 
powers down, the image is displayed. Startup Logo: allows you to display a blank screen instead of the default screen 
at startup. Blank Screen: determines what color is displayed when you select Blank Screen 
in the Startup Logo menu and when no source is displayed. Language: allows you to select a language for the onscreen display.Custom key: allows you to assign a different function to the Custom key on the 
remote, allowing you to quickly and easily use that function. Highlight an effect and 
press Select to choose a different one.Blank Screen: displays a solid blank image.Freeze: takes a snapshot of the projected image. If you’re watching video, the 
source video continues to run but the image is frozen.Source Info: the default effect. It opens a window with projector and source 
information.Service Info: opens the Service info window.Source 4: selects source 4 (by default, Source 4 is the Composite input). This 
gives you 4 direct source options on the remote. See 
page
 24.
Startup Logo
Blank Screen
Language menu
Custom Key
K1 RG.fm  Page 25  Thursday, September 27, 2007  10:24 AM 
						

							26
Service: To use these features, highlight them and press Select.
Factory Reset: restores all settings to their default.Reset Lamp hours: resets the lamp hours used counter in the Service Info 
menu to zero. Do this only after changing the lamp. Test Pattern: displays a test pattern. To display test patterns, first you must 
assign Blank Screen to the Custom key (
page
 25), then click the Test pattern 
check box in the Service menu to turn the option on, exit the menus, then 
press the Custom button on the remote. To select the patterns, use the up/
down arrows on the remote. To exit the test patterns, press the Custom 
button.Blue Only: turns off the Red and Green portions of the input, allowing you 
to properly adjust the color balance with a SMPTE color bar pattern.HDMI DDC: turns the EDID extension on and off. Some graphic cards can
-
not recognize the projector’s EDID. By default, the extensions are on (check
-
boxes are checked). Change these settings if you have trouble using HDMI or 
DVI sources.Serial Port: allows you to select the baud rate to accommodate some older, 
slower external control systems.Service Info: provides information about the projector’s software, serial 
number, and lamp.Service Code: only used by authorized service personnel.
Source Info: provides information about the active source.
Service menu
HDMI menuSerial Port menu
Service Info Source Info menu
K1 RG.fm  Page 26  Thursday, September 27, 2007  10:24 AM 
						

							27
MaintenanceReplacing the projection lampThe lamp hours timer in the Service Info menu counts the number of hours the 
lamp has been in use. Twenty hours before the lamp life expires, a message appears 
on the screen at startup indicating that you should change the lamp. The LED on 
top of the projector also blinks red twice to indicate that the lamp should be 
changed.NOTE: You can order new lamp housings from www.infocus.com (in select areas), 
your retailer or your dealer. Use only a replacement lamp with the same type and 
rating as the original lamp.
WA R N I N G:To avoid burns, allow the projector to cool for at least 60 minutes before 
you replace the lamp.Be extremely careful when removing the lamp housing. In the unlikely 
event that the bulb ruptures, small glass fragments may be generated. The 
lamp housing is designed to contain these fragments, but use caution when 
removing the lamp housing. Before replacing the lamp, clean the lamp 
compartment and dispose of cleaning materials. Wash hands after lamp 
replacement. 
 
Hg – Lamp contains mercury. Manage in accordance with local dis
-
posal laws. See www.lamprecycle.org.
1
Turn off the projector and unplug the power cord. If ceiling mounted, discon
-
nect all cables and detach the projector from the ceiling mount.
2
Wait 60 minutes to allow the projector to cool thoroughly.
3
Turn the projector upside down on a soft cloth so that the lamp door is facing 
you. Remove the base or ceiling mount plate, if attached.
Lamp hours usedwait 60 minutes turn off and unplug
projector
K1 RG.fm  Page 27  Thursday, September 27, 2007  10:24 AM 
						

							28
4
Loosen the two captive screws on the lamp door and lift the door off.
5
Loosen the two captive screws that attach the lamp housing to the projector.
6
Carefully remove the lamp housing. Dispose of the lamp in an environmentally 
proper manner. 
7
Install the new lamp housing and tighten the screws.
8
Replace the lamp door.
9
Replace the base or ceiling mount plate, if necessary.
10
Plug in the power cord and press the Pow e r button on the remote to turn the 
projector back on.
11
To reset the lamp hour timer, navigate to the Settings>Service menu and 
select Reset Lamp Hours
. See 
page
 26 for details.Reset lamp hours
Captive screws
Lamp door
Captive screws
K1 RG.fm  Page 28  Thursday, September 27, 2007  10:24 AM 
						

							29
AppendixRemote control discrete codesYou can use these codes to program another remote to learn the projector’s 
remote functions.To activate discrete mode, press and hold the Custom button on the remote for 
10 seconds. The back light blinks twice when discrete mode is entered. The 
remote buttons are now remapped to new functions as listed below. To return to 
normal remote mode, press and hold the Custom button on the remote for 10 
seconds. The remote also returns to normal mode automatically if no activity is 
detected for 2 minutes.
Projector dimensions for ceiling mount installationsAll values in millimeters (mm). 
Function
Description
Remote 
button
Power off
turns power off
Nav Up
Power on
turns power on
Nav Down
Native resize
selects Native resize
resize
16:9 resize
selects 16:9 resize
overscan
4:3 resize
selects 4:3 resize
source
Letterbox 
resize
selects letterbox resize
custom
Natural wide 
resize
selects natural wide resize
auto image
User preset 1
selects user preset 1
Source 1
User preset 2
selects user preset 2
Source 2
User preset 3
selects user preset 3
Source 3
68.95 79.2
119.91 355.91475.82
36.54 148.63
K1 RG.fm  Page 29  Thursday, September 27, 2007  10:24 AM