InFocus Projector Lp540 User Manual

							11
Skip this page if you did not connect the USB portion of the M1 com-
puter cable
For Windows 98:
 If you connected the USB cable, the Add New Hardware Wizard 
appears again. Drivers must be installed to use the USB functionality. 
The Wizard launches two times. 
The first time it detects a USB Human Interface Device (for the key-
board). 
The second time it detects a USB Human Interface Device (for the 
mouse). 
For Windows 2000, Windows ME, and Windows XP:
 The USB drivers are automatically installed.  
						

							12
Adjusting the imageAdjust the height of the projector, if necessary, by pressing the release but-
ton to extend the elevator foot. 
Rotate the leveling foot (located at the bottom back right corner), if neces-
sary.
Position the projector the desired distance from the screen at a 90 degree 
angle to the screen. 
See page 42 for a table listing screen sizes and distances.
Adjust the zoom or focus rings by rotating them until the desired image size 
and focus are produced.
If the image is not square, adjust the vertical digital keystone by using the 
buttons on the keypad. 
Press the upper Ke y s t o n e  button to reduce the upper part of the image, and 
press the lower Ke y s t o n e  button to reduce the lower part.
You can also adjust the horizontal keystone of the LP640 via the menus, or 
set the projector to automatically adjust the vertical keystone. See page 30.
Adjust the Contrast or Brightness in the Picture menu. 
See page 29 for help with the menus.
c
o
m
p
u
te
r2
n
e
tw
o
rkm
o
n
ito
r
o
u
taudioout
audioin
L
a
u
d
io
in
se
ria
lc
o
n
tro
l
c
o
m
p
u
te
rin c
o
m
p
u
te
r1
v
id
e
o2
v
id
e
oin
RS
-v
id
e
o1
adjust height
rotate
leveling 
foot
elevatorfootrelease button
computer2
networkmonitorouta
u
d
i
o
o
u
t
a
u
d
i
o
i
n
L
audioinserialcontrol
computerin computer1
video2
videoinRS-video1
adjust distanceadjust zoom and focus
focus
zoom
adjust keystone
computer
2
networkmonitoroutaudioout
audioin
L
audioinserial
control
computer
in computer
1
video
2
video
in
RS-video
1
adjust Contrast or Brightness
contrast
brightness 
						

							13
Connecting a video device Standard video connectionsPlug the audio/video (A/V) cable’s yellow connector into the video-out 
connector on the video device. Plug the other yellow connector into the yel-
low Video 2 connector on the projector. 
Plug a white connector into the left audio out connector on the video device 
and plug a red connector into the right audio out connector on the video 
device. Plug the remaining white connector into the left audio in connector 
on the projector, and plug the red connector into the right audio in connec-
tor on the projector.
Connect the black power cable to the connector on the back of the projector 
and to your electrical outlet. 
NOTE: Always use the power cable that shipped with the projector.Optional video connectionsIf the video device uses a round, four-prong S-video connector, plug an 
S-video cable (sold separately) into the S-video connector on the video 
device and into the S-Video 1 connector on the projector. Use the A/V 
cable’s audio connectors as described directly above (the yellow connectors 
on the A/V cable are not used).
To connect a progressive scan EdTV or HD source, use the Component to 
M1 adapter (sold separately).
connect A/V cable
computer 2
networkmonitor out
audio out
audio in
L
audio in
serial control
computer incomputer 1
video 2
video in
RS-video 1
 connect power cable
computer 2
networkmonitor outaudio out
audio in
L
audio in
serial control
computer incomputer 1
video 2
video in
RS-video 1
connect S-video and video cables
computer 2
networkmonitor out
audio out
audio in
L
audio in
serial control
computer incomputer 1
video 2
video in
RS-video 1 
						

							14
Displaying a video imageRemove the lens cap. 
Press the Pow e r button on the top of the projector or the remote.
The LED flashes green and the fans start to run. When the lamp comes on, 
the startup screen is displayed and the LED is steady green. It can take a 
minute for the image to achieve full brightness. The Interactive Display on 
the projector indicates the startup status.
? No startup screen? Get help on page 16.
Plug in and turn on the video device.
The video device’s image should appear on the projection screen. If it 
doesn’t, press the Video button on the keypad. 
Adjust the height of the projector by pressing the release button to extend 
the elevator foot. Rotate the leveling foot, if necessary. 
Position the projector the desired distance from the screen at a 90 degree 
angle to the screen. See page 42 for a table listing screen sizes and distances 
to the screen.
remove lens cappress Power buttonturn on video device
c
o
m
p
u
te
r2
n
e
tw
o
rkm
o
n
ito
r
o
u
taudioout
audioin
L
a
u
d
io
in
s
e
ria
lc
on
tro
l
c
o
m
p
u
te
rin c
o
m
p
u
te
r1
v
ide
o2
v
id
e
oin
RS
-v
id
e
o1
adjust height
rotate
leveling 
foot
elevatorfootrelease button
adjust distance
computer2
networkmonitorouta
u
d
i
o
o
u
t
a
u
d
i
o
i
n
L
audioinserialcontrol
computerin computer1
video2
videoinRS-video1 
						

							15
Adjust the zoom or focus rings by rotating them until the desired image size 
and focus are produced.
If the image is not square, adjust the vertical keystone using the buttons on 
the keypad. 
Press the upper Ke y s t o n e  button to reduce the upper part of the image, and 
press the lower Ke y s t o n e  button to reduce the lower part.
You can also adjust the horizontal keystone on the LP640 via the menus, or 
set the projector to automatically adjust the vertical keystone. See page 30.
Adjust the volume on the keypad or remote.
Adjust the Contrast, Brightness, Color, or Tint in the Picture menu. 
See page 29 for help with the menus.
adjust zoom and focus
focus
zoom
adjust keystone
computer
2
networkmonitoroutaudioout
audioin
L
audioinserial
control
computer
in computer
1
video
2
video
in
RS-video
1
adjust volume
computer
2
networkmonitorout
audio out
audio in
L
audioin
serial
control
computer
in computer
1
video
2
video
in
RS-video
1
adjust Picture menu 
						

							16
Shutting down the projectorThe projector automatically blanks the screen after no active source is 
detected for 30 minutes. This blank screen helps preserve the life of the pro-
jector. The image returns when an active source is detected or a remote or 
keypad button is pressed. The Interactive Display on the projector indicates 
the shutdown status.
Screen Save
You can make the blank screen appear after five minutes by turning on 
Screen Save in the Settings>System menu. See page 33. There are six time 
options for the Screen Save feature. They range from five minutes to 30 min-
utes with five minute intervals.
Pow e r  S av e
The projector also has a Power Save feature that automatically turns the 
lamp off after no signals are detected for 5 minutes. After 3 additional min-
utes with no signal, the projector powers down. If an active signal is 
received before the projector powers down, the image is displayed. You 
must press the Pow e r button to display an image after 30 minutes have 
passed. When Power Save is enabled, Screen Save is disabled. See page 33.
Turning off the projector
To turn off the projector, press the Powe r button and verify that you want to 
turn the projector off by pressing the Powe r button again within 3 seconds. 
You can cancel the shutdown by not pressing the Pow e r button a second 
time. The lamp turns off and the LED blinks green for 1 minute while the 
fans continue to run to cool the lamp. When the lamp has cooled, the LED 
lights green and the fans stop. Unplug the power cable to completely power 
off the projector.
Troubleshooting your setupIf your image appears correctly on the screen, skip to the next section 
(page 25). If it does not, troubleshoot the setup. The Interactive Display and 
LED on top of the projector indicate the state of the projector and can help 
you troubleshoot. 
 
The following tables show common problems. In some cases, more than one 
possible solution is provided. Try the solutions in the order they are pre-
sented. When the problem is solved, you can skip the additional solutions.
Table 1: LED behavior and meaning
LED color/behavior
Meaning
solid green The projector is plugged in, or the projec-
tor has been powered on and the soft-
ware has initialized. The projector has 
been turned off and the fans have stopped.
blinking green The power button has been pressed and 
the software is initializing, or the projec-
tor is powering down and the fans are 
running to cool the lamp.
blinking red
see page 42 for more informationA fan or lamp failure has occurred. Make 
sure the vents aren’t blocked (see 
page 22). Turn off the projector and wait 
one minute, then turn the projector on 
again. If the Replace Lamp message 
appears, replace the lamp and reset the 
lamp timer. Contact Technical Support if 
the problem persists
.
solid red An unidentifiable error : please contact 
Technical Support. 
						

							17
Source Troubleshooting
Problem Solution Result
No startup screenPlug power cable in, press Power button. 
Remove lens cap.Correct image
Only startup screen appears
Press the Computer button 
Activate laptop’s external portComputer image projected
computer
2
networkmonitoroutaudioout
audioin
L
audioin
serial
control
computer
in computer
1
video
2
video
in
RS-video
1
c
o
m
p
u
t
e
r
2
n
e
t
w
o
r
km
o
n
ito
r
o
u
t
a
u
d
i
o
o
u
t
a
u
d
i
o
i
n
L
a
u
d
io
in
s
e
r
ia
l
c
o
n
tr
o
l
c
o
m
p
u
te
r
in c
o
m
p
u
te
r
1
v
id
e
o
2
v
id
e
o
in
RS
-
v
id
e
o
1
computer
2
networkmonitoroutaudioout
audioin
L
audioin
serial
control
computer
in computer
1
video
2
video
in
RS-video
1
computer2
networkmonitorouta
u
d
i
o
o
u
t
a
u
d
i
o
i
n
L
audioin
serialcontrol
computerin computer1
video2
videoin
RS-video1
A
or restart
laptop
c
o
m
p
u
t
e
r2
n
e
t
w
o
r
km
o
n
i
t
o
r
o
u
ta
u
d
i
o
o
u
t
a
u
d
io
i
n
L
a
u
d
i
o
i
n
s
e
r
i
a
lc
o
n
t
r
o
l
c
o
m
p
u
t
e
ri
n c
o
m
p
u
t
e
r1
v
i
d
e
o2
v
i
d
e
oi
n
RS
-
v
i
d
e
o1
A
A 
						

							18
No computer image, just the words “Signal out of 
range” Adjust computer refresh rate in Control 
Panel>Display>Settings>Advanced>
Adapter (location varies by operating 
system)Computer image projected
The video embedded in my PowerPoint 
presentation does not play on the screenTurn off the internal LCD display on your 
laptopEmbedded video plays correctly
c
o
m
p
u
t
e
r2
n
e
t
w
o
r
km
o
n
i
t
o
r
o
u
taudioout
audioin
L
a
u
d
i
o
i
ns
e
r
i
a
lc
o
n
t
r
o
l
c
o
m
p
u
t
e
ri
n c
o
m
p
u
t
e
r1
v
i
d
e
o2
v
i
d
e
oi
n
RS
-
v
i
d
e
o1
A
Signal out of
range
You may also need to set a different 
resolution on your computer, as shown
in the following problem, “Image fuzzy
or cropped”
c
o
m
p
u
t
e
r2
n
e
t
w
o
r
km
o
n
i
t
o
r
o
u
taudioout
audioin
L
a
u
d
i
o
i
ns
e
r
i
a
lc
o
n
t
r
o
l
c
o
m
p
u
t
e
ri
n c
o
m
p
u
t
e
r1
v
i
d
e
o2
v
i
d
e
oi
n
RS
-
v
i
d
e
o1
A
A
c
o
m
p
u
t
e
r2
n
e
t
w
o
r
km
o
n
i
t
o
r
o
u
taudioout
audioin
L
a
u
d
i
o
i
ns
e
r
i
a
lc
o
n
t
r
o
l
c
o
m
p
u
t
e
ri
n c
o
m
p
u
t
e
r1
v
i
d
e
o2
v
i
d
e
oi
n
RS
-
v
i
d
e
o1
A
AB
c
o
m
p
u
t
e
r2
n
e
t
w
o
r
km
o
n
i
t
o
r
o
u
taudioout
audioin
L
a
u
d
i
o
i
ns
e
r
i
a
lc
o
n
t
r
o
l
c
o
m
p
u
t
e
ri
n c
o
m
p
u
t
e
r1
v
i
d
e
o2
v
i
d
e
oi
n
RS
-
v
i
d
e
o1
A
B 
						

							19
Image fuzzy or cropped Set your computer’s display resolution to 
the native resolution of the projector 
(Start>Settings>Control 
Panel>Display>Settings tab, select 
1024x768) Image clear and not cropped
Remote control not advancing PowerPoint slides Connect USB cable (page 7) then load USB 
drivers, if needed (page 10).Remote advances slides
See page 25 for information on the remote
A
AA
For a laptop,
disable laptop
monitor
or turn-on dual-
display mode
A
X
computer 2
networkmonitor out
audio out
audio in
L
audio in
serial control
computer incomputer 1
video 2
video in
RS-video 1
  
						

							20
Projector troubleshooting
Problem Solution Result
Image not square Adjust keystone on keypad or Picture menuSquare image
Image not sharpAdjust the focus lens or Sharpness in the 
Picture>Advanced menuCorrect image
Image does not fit 16:9 screenChange aspect ratio to 16:9 in 
Picture>Aspect ratio menuCorrect image
computer
2
networkmonitoroutaudioout
audioin
L
audioinserial
control
computer
in computer
1
video
2
video
in
RS-video
1
ABAB
AB