InFocus Projector Lp500 User Manual

35
Display Startup Screen
This setting toggles between On and Off. When this feature is On, 
the startup screen appears when the projector starts up and 
remains until an active source is detected. The startup screen con-
tains contact information. When it is off, a plain black or blue 
screen is displayed instead of the startup screen.
Reset
Highlight Reset then press menu/select to reset the options in the 
menus (except Language, Video Standard, Ceiling and Rear 
Project, and Standby Time) to their...

36
Using the Projector
Status Menu
This is a read-only menu for informational purposes. To display 
the Status menu, highlight Status from the Main menu, then 
press 
menu/select. 
FIGURE 27
Status menu
Lamp Hours Used
Indicates how many hours the current lamp has been in use. The 
counter starts at zero hours and counts each hour the lamp is in 
use. Replace the bulb when the brightness is no longer accept-
able. See “Replacing the Projection Lamp” on page 45 for details.
Computer Resolution (computer...

37
PROJECTOR MANAGER SOFTWARE
This software is included on the Online CD. It allows you to 
adjust some projector settings directly from your computer, 
rather than from the projector’s menus. The CD also contains a 
software driver that must be installed to use Projector Manager 
software.
NOTE: Projector Manager soft-
ware requires Windows 98, Win-
dows ME, or Windows 2000 or 
higher or Mac OS 9.1 and a USB 
port.
Installing the Software
To install:
1Connect the projector to your computer. Be sure to...

38
Projector Manager Software
Using the Software
To launch the software, double-click the Projector Manager icon 
in the Control Panel or in the system tray. The Projector Manager 
software opens to the General menu.
FIGURE 28
General menu
General menu
Choose the desired source from the Source pull-down menu to 
change the active source.
Click Standby to display a blank screen. You can select a black, 
blue, or white screen from the Display tab (see page 39).
Click Reset to reset the options in the menus...

39
Display menu
F
IGURE 29
Display menu
Key s t o n e
Use the slider bar to adjust the keystone setting. See page 23 for 
details on keystone.
Brightness, Contrast, Tint and Color
Use the slider bars to adjust Brightness, Contrast, Tint, and Color. 
See page 26 for a description of these settings.
Blank Screen
Blank Screen determines what color is displayed when there is no 
active source and when the projector is in standby. Click Blue, 
Black or White to specify the color. 

40
Projector Manager Software
Image menu
F
IGURE 30
Image menu
Resize
Resize 
allows you to select from among four different re-sizing 
options. The default is 
Standard, which resizes the image from its 
original version to fit a standard 4x3 aspect ratio screen. 
Wide-
screen Letterbox
 preserves the 16x9 aspect ratio of the original 
theater version, but the image is placed in a 4x3 space, so black 
bars appear at the top and bottom of the image. 
Enhanced Wide-
screen
 also preserves the aspect ratio...

41
Manual Sync
The projector adjusts signal synchronization automatically for 
most computers. But if the projected computer image looks fuzzy 
or streaked, try turning 
Auto Image off then back on again. If the 
image still looks bad, try adjusting the signal synchronization 
manually:
1Turn Auto Image off.
2Move the slider to adjust Manual sync until the image is sharp 
and free of streaks.
Manual Tracking
The projector adjusts tracking automatically to match the video 
signal from your computer....

42
Projector Manager Software
Controls menu
F
IGURE 31
Controls menu
Video Standard
NOTE: If you already know the
video standard used in your
geographical area, it’s often best to
manually select it.
When Video standard is set to Auto, the projector attempts to 
pick the video standard (NTSC, PAL, PAL-M, PAL-N, or 
SECAM) automatically based on the input signal it receives. (The 
video standard options may vary depending on your region of 
the world.) If the projector is unable to detect the correct...

43
Auto Source Select
When this feature is Off, the projector defaults to the source 
selected in Default Source. To display another source, you must 
manually select one by pressing the 
source button on the keypad 
or the 
data or video button on the remote, or by using the Source 
option in Projector Manager. When this feature is On, the projec-
tor automatically finds the active source, checking the default 
source first. Click the check box to turn this feature on and off.
Display Messages
When this...

44
Projector Manager Software
Status menu
F
IGURE 32
Status menu
Lamp Hours Used
Indicates how many hours the current lamp has been in use. The 
counter starts at zero hours and counts each hour the lamp is in 
use. Replace the bulb when the brightness is no longer accept-
able. See “Replacing the Projection Lamp” on page 45 for details.
Source Resolution 
Shows your computer’s resolution setting. To change this, go to 
your computer’s Control Panel and adjust the resolution in the 
Display tab. See your...