InFocus Projector Lp500 User Manual

25
Using the On-Screen Menus
The projector
 has menus that allow you to make image adjust-
ments and change a variety of settings. These adjustments aren’t 
available directly from the keypad. 
NOTE: Some menu items may be 
grayed out (dimmed) at certain 
times. This indicates the item is 
not applicable to your setup or the 
item is not enabled until another 
selection is made.
To open the on-screen menus, press the menu/select button on the 
keypad or remote. (The menus automatically close after 60...

26
Using the Projector
Display Menu
To access the Display menu settings, press the 
menu/select button 
to display the Main menu, press the down arrow to highlight 
Display, then press 
menu/select again to access the Display menu.
 
FIGURE 20
Display menu
Key s t o n e
This option helps to keep the image square as the angle of projec-
tion is changed. Use this feature to adjust the image vertically 
and make a squarer image. See page 23 for details on keystone 
adjustments.
1Press the down button to...

27
Contrast
The contrast controls the degree of difference between the light-
est and darkest parts of the picture. Adjusting the contrast 
changes the amount of black and white in the image.
1Use the up and down arrows to highlight Contrast, press 
menu/select, use the arrows to adjust the contrast, then press 
menu/select to accept your changes.
Tint
NOTE: The color setting applies 
to video sources only. The tint set-
ting applies to NTSC video sources 
only.
The tint adjusts the red-green color...

28
Using the Projector
Audio Menu
 
FIGURE 21
Display menu
Vo l u m e
You can also adjust the volume directly from the projector’s key-
pad.
1Use the up and down arrows to highlight Volume, press 
menu/select, use the arrows to adjust the volume, then press 
menu/select to accept your changes.
Mute
This mutes the sound.
1Use the up and down arrows to highlight Mute, press 
menu/select, use the left or right arrow to turn mute on and off 
(a green dot indicates a feature is on), then press 
menu/select...

29
Image Menu 
To access the Image menu settings, press the 
menu/select button 
to display the Main menu, press the down arrow to highlight 
Image, then press 
menu/select again to access the Image menu.
FIGURE 22
Image menu for computer sources
Resize
Resize 
allows you to select from among four different re-sizing 
options. The default is 
Standard, which resizes the image from its 
original version to fit a standard 4x3 aspect ratio screen. 
Wide-
screen Letterbox
 preserves the 16x9 aspect ratio of...

30
Using the Projector
Zoom
This allows you to enter zoom mode without using the remote. 
Highlight 
Zoom, press menu/select, use the left or right arrow 
buttons to turn zoom mode on, then press 
menu/select. Exit the 
menus to use the zoom feature. The zoom icon appears in the 
lower right corner. Use the right mouse button to zoom in and 
use the left mouse button to zoom out. Use the keypad naviga-
tion buttons on the keypad to pan the zoomed image. To exit 
zoom mode, either turn the feature off in...

31
Horizontal Position 
Follow these steps to manually adjust the horizontal position:
1Turn Auto image off.
2Highlight Horizontal position, press 
menu/select, use the 
arrow buttons to adjust the Horizontal position, then press 
menu/select.
Positioning adjustments are saved when you turn off the projec-
tor.
Ve r t i c a l  Po s i t i o n  
Follow these steps to manually adjust the vertical position.
1Turn Auto image off.
2Highlight Vertical position, press 
menu/select, use the arrow 
buttons to...

32
Using the Projector
Color Management Menu
FIGURE 23
Color Management menu
Degamma
This allows you to select a gamma table that has been specifically 
tuned for either computer, video, or film input.
Highlight 
Degamma, press menu/select, use the left or right 
arrows to cycle through the options, then press 
menu/select to 
select.
Auto Color Gain
When this feature is On, the projector automatically sets the red, 
green, and blue color gains for each source. When it is off, you 
can manually adjust...

33
Control Menu
To access the Control menu settings, press the 
menu/select button 
to display the Main menu, press the down arrow to highlight 
Control, then press 
menu/select again to access the Control menu.
FIGURE 24
Control menu
Auto Source 
When this feature is On, the projector automatically finds the 
active source, checking the default source first. When this feature 
is Off, the projector defaults to the source selected in Default 
Source. To display another source, you must manually select...

34
Using the Projector
Advanced Menu
FIGURE 25
Advanced menu
Rear Project
When you turn Rear Project on, the projector reverses the image 
so you can project from behind a translucent screen. 
Highlight 
Rear Project, press menu/select, then press the left or 
right arrow buttons to turn this feature off and on.
Ceiling Project
When you turn Ceiling Project on, the projector turns the image 
upside down for ceiling-mounted projection. Highlight Ceiling 
Project, press 
menu/select, then press the left or...