InFocus Projector IN5554L User Manual

1
Declaration of Conformity
Manufacturer: InFocus Corporation, 13190 SW 68th Parkway, Portland, Oregon 
97223-8368 USA
We declare under our sole responsibility that this projector conforms to the 
following directives and norms:
EMC Directive 2004/108/EC
ErP Directive 2009/125/EC
EMC: EN 55022: 2010
 EN 55024: 2010
 EN 61000-3-2: 2006+A2:2009
 EN 61000-3-3:2008
Low Voltage Directive 2006/95/EC
Safety: IEC 60950-1:2005; EN 60950-1:2006+A12:2011
Trademarks
Apple, Macintosh, and PowerBook are trademarks or...

2
Table of Contents
Introduction  4
Positioning the projector  6
Ceiling Mount  7
Connecting power  8
Connecting a computer source  8
Displaying an image  9
Adjusting the image  10
Connecting a video device  11
Video device connections  11
Shutting down the projector  12
Troubleshooting your setup  12
Using the remote control  20
Using the keypad buttons  22
Using the menus 23
Input menu  24
Picture menu  25
Lamps menu 26
Alignment menu  27
Control menu  28
Service menu 29
Using Projector Web Controls...

3
Important Operating Considerations for Safety
• Refer to this guide for proper startup and shutdown procedures.
• Follow all warnings and cautions in this manual and on the projector.
• Do not block the lens with any object while the projector is being used. 
Bl
 ocking the light path can cause  overheating and result in fire.
• Place the projector in a horizontal position no greater than 8 degrees off axis.
• Locate the projector at least 4 (1.2m) away from any heating or cooling vents.
• Do not block...

4
Introduction
Your new digital projector is simple to connect, easy to use, and straightforward to 
maintain. It is a versatile projector that is flexible enough to fit almost any 
installation scenario. The IN5552L and IN5852L have XGA 1024 x 768 resolution, 
the IN5554L and IN5854L have WXGA 1280x800 resolution, and the IN5555L and 
IN5855L have native WUXGA 1920x1200 resolution. This guide applies to all three 
products. They are compatible with a wide variety of computers and video devices. 
Note:...

5
Connector Panel
The projector provides both computer and video connection options, including:
•HDMI
•DVI-D
• 3G-SDI
• BNC RGBHV and YPbPr for RGBHV, EDTV and HDTV
• RGB (VGA) computer
•S-video
• Composite video
The projector also provides the following connectors:
• LAN port for network control and web server.
• 12V screen trigger output
•Wired remote jack
• RS-232 connector for serial control. Command control codes are in the 
Ap
 pendix and on our support website at  www.infocus.com/support.
12V...

6
Positioning the Projector
To determine where to position the projector, consider the size and shape of your 
screen, the location of your power outlets, and the distance between the projector 
and the rest of your equipment. Here are some general guidelines:
• Position the projector on a flat surface at a right angle to the screen. The p
 rojector (with the standard zoom lens, LENS-074) must be at 55.8”/
1.42m(XGA) ; 60.2”/1.53m (WXGA) ; 57.2”/1.45m (WUXGA) from the 
projection screen. See appendix for...

7
Ceiling Mount
If you wish to install the projector on the ceiling:
• The projector must be installed by a qualified professional in order to ensure pr
 oper operation and reduce the risk  of hazards or injury. It is not 
recommended you install the projector yourself.
• We strongly recommend using InFocus approved ceiling mounts for proper  fi
 tting, ventilation and installation.  Refer to the ceiling mount installation 
guide for more information.  The warranty does not cover any damage caused 
by...

8
Connecting power
Connect the black power cord to the Pow e r connector on the side of the projector 
and to your electrical outlet. Turn on the power switch. The Power LED on the top 
of the projector ( page 12) turns red.
NOTES : Note: Connect
 ion to a circuit with a minimum of 20A capacity is 
recommended. Always use the power cord that shipped with the projector.
Connecting a computer source
HDMI 1.3 connection
Plug an HDMI cable into the video out connector on the video device and into the 
HDMI...

9
Displaying an image
Touch the Pow e r button on the keypad or the remote.
The Power button blinks green and the fans start to run. When the lamp turns on, 
the
  start up screen will display and the Power button will become solid green. It 
can take a minute for the image to achieve full brightness.
No start up screen?  Get h
 elp on page 13 .
Turn on your computer or video device.
The image should appear on the projection screen. If it doesn’t, press the  Inpu
 t 
button on the projector’s keypad or...