InFocus Projector IN5554L User Manual

							1
Declaration of Conformity
Manufacturer: InFocus Corporation, 13190 SW 68th Parkway, Portland, Oregon 
97223-8368 USA
We declare under our sole responsibility that this projector conforms to the 
following directives and norms:
EMC Directive 2004/108/EC
ErP Directive 2009/125/EC
EMC: EN 55022: 2010
 EN 55024: 2010
 EN 61000-3-2: 2006+A2:2009
 EN 61000-3-3:2008
Low Voltage Directive 2006/95/EC
Safety: IEC 60950-1:2005; EN 60950-1:2006+A12:2011
Trademarks
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of 
Apple Computer, Inc. IBM is a trademark or registered trademark of International 
Business Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or 
registered trademarks of Microsoft Corporation. Adobe and Acrobat are 
trademarks or registered trademarks of Adobe Systems Incorporated. DLP® and the 
DLP logo are registered trademarks of Texas Instruments and BrilliantColor™ is a 
trademark of Texas Instruments. InFocus, In Focus, and INFOCUS (stylized) are 
either registered trademarks or trademarks of InFocus Corporation in the United 
States and other countries
NOTE: This product is covered electrical and electronic equipment 
under the European Unions Waste from Electrical and Electronic 
Equipment (WEEE) Directive (2002/96/EC). The WEEE Directive 
requires that covered equipment be collected and managed separately 
from typical household waste in all EU member states. Please follow 
the guidance of your local environmental authority or ask the shop 
where you purchased the product for collection or recycling options.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following 
two conditions: (1) This device may not cause harmful interference, and (2) this device 
must accept any interference received, including interference that may cause 
undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B 
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to 
provide reasonable protection against harmful interference in a residential installation. 
This equipment generates, uses and can radiate radio frequency energy and, if not 
installed and used in accordance with the instructions, may cause harmful interference 
to radio communications. However, there is no guarantee that interference will not 
occur in a particular installation. If this equipment does cause harmful interference to 
radio or television reception, which can be determined by turning the equipment off 
and on, the user is encouraged to try to correct the interference by one or more of the 
following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the 
receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by InFocus Corporation may void 
authority to operate the equipment.
Canada
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil 
numérique de la classe B est conforme à la norme NMB-003 du Canada.
Agency Approvals
UL, cUL, TUV-GS, SASO, SABS, KC, NOM, PCT, PSB, UL-S(Argentina), C-tick, FCC and 
CE 
Other specific Country Approvals may apply. Please see product certification label.
This document applies to regulatory models IN5552L, IN5554L, IN5555L, IN5852L, 
IN5854L, and IN5855L.
Input ratings: AC 110-240V, 9-4A, 50-60Hz
InFocus reserves the right to alter product offerings and specifications at any time 
without notice. 
						

							2
Table of Contents
Introduction  4
Positioning the projector  6
Ceiling Mount  7
Connecting power  8
Connecting a computer source  8
Displaying an image  9
Adjusting the image  10
Connecting a video device  11
Video device connections  11
Shutting down the projector  12
Troubleshooting your setup  12
Using the remote control  20
Using the keypad buttons  22
Using the menus 23
Input menu  24
Picture menu  25
Lamps menu 26
Alignment menu  27
Control menu  28
Service menu 29
Using Projector Web Controls  30
Maintenance 34
Cleaning the lens  34
Replacing the projection lamps 34
Replacing the lens  36
Replacing the filters  37
Changing the color wheel 38
Using the security lock  39
Appendix  40
Optional Lenses 40
PiP Compatibility 46
RS-232 commands  47
Index 54 
						

							3
Important Operating Considerations for Safety
• Refer to this guide for proper startup and shutdown procedures.
• Follow all warnings and cautions in this manual and on the projector.
• Do not block the lens with any object while the projector is being used. 
Bl
 ocking the light path can cause  overheating and result in fire.
• Place the projector in a horizontal position no greater than 8 degrees off axis.
• Locate the projector at least 4 (1.2m) away from any heating or cooling vents.
• Do not block ventilation openings. Locate the projector in a well-ventilated  ar
 ea without obstructions to intake or exhaust vents. Do not place the 
projector on a tablecloth or other so ft covering that may block the vents.
• Do not place the projector in direct sunlight, humid, greasy or dusty places or  in
  places where the projector may come into contact with smoke or steam.
• Do not look directly into the lens while the projector is being used.
• Do not drop the projector.
• Do not spill liquid on the projector. Spilled liquid may damage the projector.
• Use the power cord provided. Connect the power cord to a receptacle with a  pr
 otective safety (earth) ground terminal. A surge-protected power strip is 
recommended.
• Do not overload wall outlets.
• When disconnecting the power cord, hold the plug, not the cord.
• Wash hands after handling the cables supplied with this product.
• The projector remote control uses batteries. Make sure the batteries’ polarity  (+/-)
  is aligned correctly. Dispose of us ed batteries in accordance with local 
disposal laws.
• Use an InFocus approved ceiling mount kit for proper fitting, ventilation and  ins
 tallation.  The warranty does not cover any damage caused by use of non-
approved ceiling mount kits or by installing in an improper location. 
• When the projector is ceiling mounted, wear protective eyewear to prevent  e
 ye injury before opening lamp door. • The projector must be installed by a qualified professional in order to ensure 
pr
 oper operation and reduce the risk of hazards or injury. It is not 
recommended you install the projector yourself.
• Refer all service to qualified service personnel. Servicing your own projector  c
 an be dangerous to you and will void the warranty.
• Only use replacement parts specified by InF
 ocus.  Unauthorized substitutions 
may result in fire, electrical shock, or injury, and may void the warranty.
• Only genuine InFocus lamps are tested for use in this projector. Use of non  In
 Focus lamps may cause electrical shock and fire, and may void the projector 
warranty. 
• Hg – Lamp contains mercury. Manage in accordance with local  disposal laws. See  www.lamprecycle.org.
• The projector uses a high-pressure mercury glass lamp.  The lamp may fail 
prematurely, or it may rupture with a popping sound if jolted, scratched, or 
handled while hot.  The risk of lamp failure or rupture also increases as the 
lamp age increases; please replace  the lamp when the Lamp LED is red.
• In the unlikely event of a lamp rupture, particles may exit through the  pr
 ojector vents. Please keep people, food, and drinks out of the “keep out” 
area under and around the projector, as indicated by the illustration.
 
Follow these instructions to help ensure im age quality and lamp life over the life of 
the projector. Failure to follow these instructions may affect the warranty. For 
complete details of the warranty , see the Safety/Warranty Booklet. 
						

							4
Introduction
Your new digital projector is simple to connect, easy to use, and straightforward to 
maintain. It is a versatile projector that is flexible enough to fit almost any 
installation scenario. The IN5552L and IN5852L have XGA 1024 x 768 resolution, 
the IN5554L and IN5854L have WXGA 1280x800 resolution, and the IN5555L and 
IN5855L have native WUXGA 1920x1200 resolution. This guide applies to all three 
products. They are compatible with a wide variety of computers and video devices. 
Note: These projectors do not ship with a le ns. An optional lens must be chosen for 
the product.
Product Specifications
To read the latest specifications on your multimedia projector, be sure to visit our 
support website at  www.infocus.com/support , as specifications are subject to 
change.
Online Registration
Register your projector on our website at  www.infocus.com/register to activate 
your warranty and receive product updates, announcements, and registration 
incentives.
Included Items
POWER
ON
FOCUS ZOOM LENS SHIFT
INPUT
AUTO SYNC
OVERSCAN
INFO. LIGHT
FREEZE
LAMP MODEASPECT PIP
PICTURE NETWORK OFFCLEAR SHUTTER ID SET
ENTER
MENU
1
4
78 9 5
23
6EXIT
TEST
PATTERN
0
Remote Control
Power Cord Optional RGBCMY 
Color Wheel
Documentation Dust Cap
Projector
RGB (VGA) Cord
Optional Accessories
Optional accessories include optional lenses and a ceiling mount. These items and 
other accessories can be found on our website at  www.infocus.com or at your 
local dealer.
Lens
Remote control 
receiver (IR)
Remote control 
receiver (IR)
Elevator Foot
Color Wheel cover
Power switch
Key p a d
Connector panel
Power Cord 
Connector 
						

							5
Connector Panel
The projector provides both computer and video connection options, including:
•HDMI
•DVI-D
• 3G-SDI
• BNC RGBHV and YPbPr for RGBHV, EDTV and HDTV
• RGB (VGA) computer
•S-video
• Composite video
The projector also provides the following connectors:
• LAN port for network control and web server.
• 12V screen trigger output
•Wired remote jack
• RS-232 connector for serial control. Command control codes are in the 
Ap
 pendix and on our support website at  www.infocus.com/support.
12V Screen Trigger output
The 3.5mm mini-jack screen trigger prov ides a 12 volt, 0.25 amp DC output. It 
turns on when the lamp is li t. If you connect your projection screen to this output 
using the cable that came with your screen, the screen will move down when the 
lamp is turned on and return to its stor age position when the lamp is turned off.RS-23212V Screen Trigger 
Output
Composite video
RGBHV 
YPbPr
HDMI
DVI-D
S-video
RGB 
(VGA) Wired 
remote
LAN
SDI 
						

							6
Positioning the Projector
To determine where to position the projector, consider the size and shape of your 
screen, the location of your power outlets, and the distance between the projector 
and the rest of your equipment. Here are some general guidelines:
• Position the projector on a flat surface at a right angle to the screen. The p
 rojector (with the standard zoom lens, LENS-074) must be at 55.8”/
1.42m(XGA) ; 60.2”/1.53m (WXGA) ; 57.2”/1.45m (WUXGA) from the 
projection screen. See appendix for additional lens information.
• Position the projector within 10 feet (3m) of your power source and within 6  f
 eet (1.8m) of your video device (unless you purchase extension cables). To 
ensure adequate cable access, do not place the projector within 6 inches 
(.15m) of a wall  or other object.
• Position the projector to the desired distance from the screen. The distance  fr
 om the lens of the projector to the  screen, the zoom setting, and the video 
format determine the size of the projected image.
• The image exits at a given angle. However, the lens shift feature makes the  imag
 e offset variable. 
• The vertical image offset range for all the p
 rojectors is -60% to +20% (default 
0%), and the horizontal image offset is +/-10% (default 0%). At 20% vertical 
offset, the bottom of the image is 20% of the image height above the center 
of the lens in a tabletop configuration.
Vertical Image Offset is -60-% ~ +20%
lens center 20% offset
-60% offset
Horizontal Image Offset is +/-10%
 
  
						

							7
Ceiling Mount
If you wish to install the projector on the ceiling:
• The projector must be installed by a qualified professional in order to ensure pr
 oper operation and reduce the risk  of hazards or injury. It is not 
recommended you install the projector yourself.
• We strongly recommend using InFocus approved ceiling mounts for proper  fi
 tting, ventilation and installation.  Refer to the ceiling mount installation 
guide for more information.  The warranty does not cover any damage caused 
by use of non-approved ceiling mount kits or by installing in an improper 
location.
• The ceiling must be strong enough to support the projector and the  in
 stallation must be in accordance with any local building codes. Consult your 
dealer for more information.
• The maximum physical pitch is unlimited, however the lamp life will be  ne
 gatively affected.
• The maximum supported physical horizontal roll is +/-10º. Note: Lamp life will  be
  negatively affected.
• Keep all adjacent surfaces at least 19. 7” (5
 0cm) from the sides, 12” (30cm) 
from the top and bottom of the projector, and 27.6” (70cm) from the back of 
the projector to preserve required airflow around the projector.
10º 
						

							8
Connecting power
Connect the black power cord to the Pow e r connector on the side of the projector 
and to your electrical outlet. Turn on the power switch. The Power LED on the top 
of the projector ( page 12) turns red.
NOTES : Note: Connect
 ion to a circuit with a minimum of 20A capacity is 
recommended. Always use the power cord that shipped with the projector.
Connecting a computer source
HDMI 1.3 connection
Plug an HDMI cable into the video out connector on the video device and into the 
HDMI  connector on the projector.
To take advantage of HDMI 1.3 Deep Color  (30 
 bit) you must have a 1.3-compatible 
source.
DV I - D
Plug a DVI-D cable into the video out connector on the video device and into the 
DV I   connector on the projector.
RGB (VGA) connection
Connect one end of the provided computer cable to the RGB  connector on the 
projector and the other to the VGA connector on your computer. If you are using a 
desktop computer, you will need to disconnect the monitor cable from the 
computer’s video port first.
RGBHV connection
Connect one end of the BNC cable to the computer and the other end of the cable 
into the BNC connectors on the projector.
Note: This projector does not support audio. Audio must be routed separately. 
Connect power cord
MOLEXMOLEX
Connect HDMI cable
Connect DVI-D cable
Connect RGB (VGA) cable
Connect RGBHV cable 
						

							9
Displaying an image
Touch the Pow e r button on the keypad or the remote.
The Power button blinks green and the fans start to run. When the lamp turns on, 
the
  start up screen will display and the Power button will become solid green. It 
can take a minute for the image to achieve full brightness.
No start up screen?  Get h
 elp on page 13 .
Turn on your computer or video device.
The image should appear on the projection screen. If it doesn’t, press the  Inpu
 t 
button on the projector’s keypad or remote.
If you are using a laptop, make sure its external video port is active.
Many laptops do not automatically turn on their external video port when a 
pr

ojector is connected. Usually a key combin ation like Fn + F8 or CRT/LCD key turns 
the external display on and off. Locate a  function key labeled CRT/LCD or a function 
key with a monitor symbol. Press  Fn and the labeled function key simultaneously. 
Refer to your laptop’s documentation for more information about your laptop’s key 
co
 mbination.  
No laptop image?  T
 ry pressing the Auto Sync button on the keypad or 
remote. Get help on  page 22.
Press Power button
Turn on computer or 
video device
Activate laptop’s external port
Monitor key or 
LCD/CRT key
Fn key