InFocus Projector In5504 User Manual

30
Setup menu
Language: Allows you to select a language for the onscreen display.
Network: Allows you to setup network settings. See page 34 for details on 
network configuration and operation.
•DHCP: Turns the DHCP on or off.
•IP Address: Assign Network IP Address. 
•Subnet Mask: Assign Network Subnet Mask.
•Default Gateway: Assign Network Default Gateway.
•WINS Host Name Lookup: Turns WINS Host Name Lookup on or off.
•Host Name: Displays the host name.
•MAC Address: Displays network MAC Address value....

31
Lamp Low Power: Toggles between on and off. Turn it on to lower the light 
output of the lamp. This also lowers the fan speed, making the projector 
quieter.
Current Lamp: (IN5532/IN5534 only) Controls which lamp(s) is in use.
Lamp Auto Switch: (IN5532/IN5534 only) Controls when the projector 
switches between lamps. Choices include: upon failure, at power-up, or 
after a set number of hours.
Power Sounds: Controls whether the projector makes a sound when 
powered on and off.
Internal Speakers: Allows...

32
Select again to turn off magnify controls and use the arrow buttons to 
advance slides.
Lens Adjust Enable: When turned on, lens shift, zoom, focus, digital keystone, 
auto keystone and pincushion adjustments can be made. When the product 
has been mounted, installers can turn this feature off to prevent changes to 
lens shift, zoom, focus, keystone and pincushion settings.
Keypad Enable: Enables or disables keypad.
Glow Ring: Controls the brightness level of the glow ring status indicator.
PIN...

33
Status and Service menu
Source Info: Displays current source settings (read-only).
Projector Info: Displays current projector settings (read-only).
Reset Lamp Hours: Resets the lamp hours used counter in the Projector Info 
menu to zero. Do this only after changing the lamp.
Factory Reset: Restores all settings to their default.
Service Code: Only used by authorized service personnel.
Help
Press Help (on the keypad or remote) at any time to get interactive help for 
solving common, picture, sound, and...

34
Using Network Functions
IMPORTANT: To enable network functions at all times (even when the 
projector is powered off), the Network item in the Always-On Functions 
submenu in the Setup menu must be set to Yes (not No).
Projector network functions include:
• Configuring and controlling the projector via a web browser.
• Failure and warning alerts via email.
• Projector Management via SNMP.
• Controlling the projector via Scheduling.
NOTE: Projector web pages and emails sent by the projector are always...

35
3Start a web browser on your computer.
4Enter the projectors IP address or host name (preceded by http://) into 
the web browsers address bar. Example: If the IP address is 
192.168.1.10, enter http://192.168.1.10 into the browsers address bar.
5The Log In to Projector Control page will be shown in the browser.
6Select Access type: Basic User or Administrator.
7Click Log In.
Navigating Projector Web Pages
The left side of every page shows a navigation bar. Click the links in the 
navigation bar to go...

36
Event Notifications Page (administrators only)
This page lets you configure the projector to automatically send email when 
specific events occur. 
E-Mail Settings tab: In the Account Used… section, enter the information 
needed for your projector to connect to an email sending (SMTP) server. 
Then in the Recipient E-Mail Addresses section, enter the email addresses of 
people who will receive emails, and for each address, select whether that 
address receives reminders and/or warnings and errors...

37
Custom commands you enter here should be in write format (do not 
include ?), and should use < and > instead of ( and ). Example: to turn 
on the ceiling mount setting, use the custom command .
User Access and Security Page (administrators only)
This page lets you configure security options for the projector, including log 
in passwords and projector access restrictions.
Web Access - Administrator tab: Select whether or not Administrators must 
enter a password to log into the projectors web pages. If...

38
Using LitePort
LitePort displays a slide show of JPEG images stored on a USB flash drive 
connected to the projector. This can eliminate the need for a computer 
source.
Image File Types
LitePort displays image files in JPEG format only (file extensions .JPEG and 
.JPG). Other file types including PDF, BMP, TIFF, PNG, GIF, etc. are 
ignored.
Viewing a Slide Show
To view your pictures as a slide show, follow these steps:
1Connect a USB flash drive to your computer and copy JPEG files from 
your...

39
(For remaining items below, highlight the setting, then press Select one or 
more times to change the setting value.)
Auto Start: Select On to have the player start the slide show when the USB 
flash drive is first connected. Select Off to have the player display 
thumbnails when the USB flash drive is first connected.
Show All Folders: Select On to have the slide show display all images in all 
folders. Select Off to have the slide show display images only from the 
current folder.
Fill Screen:...