InFocus Projector In5312 User Manual

User’s Manual 
Rear view 
 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  DC 12V TRIGGER Connect a 12V screen trigger (200ma max) 
2.  AUDIO 5 (L and R)  Connect the AUDIO CABLE from an input device 
3.  VIDEO  Connect the COMPOSITE CABLE from a video device 
4.  S-VIDEO Connect the S-VIDEO CABLE from a video device 
5.  YPbPr Connect the COMPONENT CABLE from a component video enabled 
device 
6.  BNC 
Connect the BNC CABLES from a computer or a video enabled device 
7.  AC IN Connect the POWER CABLE 
8.  Power...

IN5312/IN5314 – User’s Manual 
– 5 –  
18.  USB  Connect the USB CABLE from a computer 
                                       
(used for presentation slide control with the projector remote) 
19.  HDMI  Connect the HDMI CABLE from an HDMI device 
20.  AUDIO 2 Connect the AUDIO CABLE from an input device 
21.  DVI-D  Connect the DVI cable (not supplied) from a computer 
Solid Red Normal operation 
22.  READY LED 
Flashing 
Amber Lamp is not ready  
23.  TEMP LED 
Solid Red Overheating 
Solid Amber...

User’s Manual 
Bottom view 
 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  Leveling/Elevator Feet Raise and rotate the feet to change and fine tune 
the angle of the projector.  16 
2.  Ceiling support holes Only use with an InFocus ceiling mount system (p/n PRJ-MNT-UNIV). 
See your InFocus dealer or go to 
www.infocusstore.com. 
 
Note: 
When installing, ensure that you us e only UL Listed ceiling mounts. 
For ceiling installations, use approved mounting har dware and M4 screws with a maximum screw 
depth of 6...

IN5312/IN5314 – User’s Manual 
Remote Control Parts 
 
Important: 
1. Avoid using the projector with bright fluoresc ent lighting turned on. Certain high-frequency fluo-
rescent lights can disrupt remote control operation. 
 
2. Be sure nothing obstructs the path between the re mote control and the projector. If the path be-
tween the remote control and the projector is obstructed, you can bounce the signal off certain 
reflective surfaces such as projector screens. 
 
3. The buttons and keys on the...

User’s Manual 
– 8 – 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  Power ON Turn the projector on 12 
2.  LED indicator Only lights when the remote keys are pressed 
3.  Display Mode               Choose a suitable preset mode for usage environment 
4.  Contrast  Display the Contrast setting bar and use the right and left keys to adjust 
5.  Brightness      Display the Brightness setting bar and use the right and left keys to ad-
just. 
6.  Left cursor     When the OSD is displayed, this button navigates to the...

IN5312/IN5314 – User’s Manual 
  – 9 –  
SETUP AND OPERATION 
Inserting the Remote  Control Batteries  
1.  Remove the battery compartment 
cover by sliding the cover in the di-
rection of the arrow. 
 
2.  Insert the batteries (not included) as 
shown in the illustration. 
 
3.  Replace the cover. 
 
 
Caution: 
1. Only use AA batteries (Alkali ne batteries are recommended). 
2. Dispose of used batteries accordi ng to local ordinance regulations.  
3. Remove the batteries when not usi ng the projector...

User’s Manual 
 Installing or Removing the Optional Lens 
Caution: 
y Do not shake or place excessive pressure on t he projector or the lens components as the projec-
tor and lens components contain precision parts. 
y Before removing or installing the lens, be sure to  turn off the projector, wait until the cooling fans 
stop, and turn off the main power switch. 
y Do not touch the lens surface when removing or installing the lens. 
y Keep fingerprints, dust or oil off the lens surface. 
y Do not...

IN5312/IN5314 – User’s Manual 
Installing the New Lens 
1.  Align the notches and correctly posi-
tion the electrical contact pad as 
shown in the picture. 
Note: 
Pin of IRIS should be in the direction 
as shown in the picture. 
2.  Rotate the lens clockwise until you 
feel it click into place. 
 
  – 11  –  

User’s Manual 
Starting and Shutting down the Projector 
1.  Remove the lens cap. 
2.  Connect the power cord to the pro-
jector. Connect the other end to a 
wall outlet. Verify that the AC Power 
switch on the back of the unit is 
turned on. When connected, the 
PWR LED will turn solid amber. 
 
 
3.  Turn on the lamp by pressing the 
“
” button on the rear of the 
projector or the Power On button on 
the remote. 
The PWR LED will now flash amber. 
The startup screen will display in 
approximately 30...

IN5312/IN5314 – User’s Manual 
If more than one input device is connected, press the SOURCE button and use ▲▼ to 
scroll among devices. 4.  
•   VGA 1 : Analog RGB 
•   VGA 2 : Analog RGB 
•   B NC : Analog / serial digital interface video inputs 
•   HDMI : High Definition Multimedia Interface 
•   DVI : DVI 
•   Component Video: DVD input YCbCr / YPbPr, or HDTV input YPbPr via HD15  
connector 
• S-Video: Super video (Y/C separated) 
•  
Composite Video: Traditional composite video 
5.  To turn the...