InFocus Projector IN3134a User Manual

LAN_RJ45 
 
Wired LAN Terminal functionalites  
Remote control and monitoring of a projector from a PC (or  laptop) via wired LAN is also possible. 
Compatibility with Crestron / AMX (Device Discovery) / Extron control boxes enables not only collective 
projector management on a network but also management from a control panel on a PC (or  laptop) 
browser screen.  
   Crestron is a registered trademark of Crestron Electronics, Inc. of the United States.  
   Extron is a registered trademark of Extron...

— 35 — 
LAN_RJ45 
1. Connect an RJ45 cable to RJ45 ports on the projector and the PC (laptop). 
 
2. On the PC (laptop), select Start → Control Panel →Network and Internet. 
 
   

— 36 — 
3. Right-click on Local Area Connection, and select Properties. 
 
4. In the Properties window, select the Networking tab, and select Internet Protocol (TCP/IP). 
5. Click Properties. 
 
6. Click Use the following IP address and fill in the IP address and Subnet mask, then click OK. 
  

— 37 — 
7. Press the Menu button on the projector. 
8. Select Settings2→ Advanced1 → Network 
9. After getting into Network, input the following: 
 DHCP: Off 
 IP Address: 10.10.10.10 
 Subnet Mask: 255.255.255.0 
 Gateway: 0.0.0.0 
 DNS Server: 0.0.0.0 
10. Press  (Enter) / ► to confirm settings. 
Open a web browser  
(for example, Microsoft Internet Explorer with Adobe Flash Player 9.0 or higher). 
 
11. In the Address bar, input the IP address: 10.10.10.10. 
12. Press  (Enter) / ►. 
The projector...

— 38 — 
RS232 by Telnet Function 
Besides using Hyper-Terminal for projector control, you can also use RS232 by Telnet with the 
LAN/RJ45 interface. 
Quick Start-Guide for “RS232 by TELNET” 
1. Locate the IP address from the projectors OSD. 
2. Make sure that the laptop/PC can access the projectors web page. 
3. Make sure that the Windows firewall settings are disabled to prevent the laptop/PC from 
ignoring the Telnet commands. 
 
4. Go to Start => All Programs => Accessories => Command Prompt 
  

— 39 — 
5. Type the Telnet command in the following format: 
telnet  ttt.xxx.yyy.zzz  23 (“Enter” key pressed) 
(ttt.xxx.yyy.zzz: IP-Address of the projector) 
6. When the Telnet connection is ready and you have input an RS232 command, press Enter. 
 
Enabling Telnet in Windows Vista/7/8 
1. Telnet is not included by default in Windows Vista, 7 or 8. 
2. Open the Control Panel. 
 
3. Open Programs.  
  

— 40 — 
4. Select Turn Windows features on or off. 
 
5. Select Telnet Client, and click OK. 
 
Telnet specifications 
Telnet: TCP 
Telnet port: 23 
Telnet utility: Windows Telnet.exe (console mode) 
Disconnecting Telnet when Telnet is active: Close Windows Telnet utility.  
Telnet Limitations: 
1. Less than 50 bytes are used for the  successive network payload for the Telnet Control 
application. 
2. Less than 26 bytes are used for one complete RS232 command for Telnet control. 
3. There must be at...

— 41 — 
Advanced 2 Features 
Press the Menu button to open the OSD menu. Press the ◄► buttons to move to the Settings 2 
menu. Press the ▲▼ buttons to move to the Advanced 2 menu and then press  (Enter) or ►. 
Press the ▲▼ buttons to move up and down in the Advanced 2 menu. Press the ◄► buttons to 
enter and change setting values. 
 
ITEM DESCRIPTION 
Sleep Timer Press the ◄► buttons to enter and set the Sleep timer. The projector automatically 
turns off after the preset period of time. 
Source Filter...

— 42 — 
Source Filter 
Press the ENTER button to enter the Source Filter sub menu. This sub menu allows you to enable 
and disable source inputs. 
 
ITEM DESCRIPTION 
HDMI 1 / MHL Press the ◄► buttons to enter and enable or disable the HDMI1 / MHi-compatible 
sourceK 
HDMI 2 Press the ◄► buttons to enter and enable or disable the HDMI O sourceK 
VGA N Press the ◄► buttons to enter and enable or disable the VGA1 source. 
VGA O Press the ◄► buttons to enter and enable or disable the VGA2 source. 
p-Video...

— 43 — 
MAINTENANCE AND SECURITY 
Replacing the Projection Lamp 
The projection lamp should be replaced when it burns out. It should only be replaced with a certified 
replacement part, which you can order from your local dealer.  
 Important: 
a. The projection lamp used in this product contains a small amount of mercury. 
b. Do not dispose this product with general household waste. 
c. Disposal of this product must be carried out in accordance with the regulations of your local  
authority. 
 Warning:...