InFocus Projector IN3134a User Manual
Here you can view all the pages of manual InFocus Projector IN3134a User Manual. The InFocus manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 2
— i — Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. © Copyright 2014 Disclaimer The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically...
Page 3
— ii — Important Safety Information Important: It is strongly recommended that you read this section carefully before using the projector. These safety and usage instructions will ensure that you enjoy many years of safe use of the projector. Keep this manual for future reference. Symbols Used Warning symbols are used on the unit and in this manual to alert you of hazardous situations. The following styles are used in this manual to alert you to important information. Note: Provides...
Page 4
— iii — Projector Installation Notice Place the projector in a horizontal position The tilt angle of the projector should not exceed 15 degrees. In addition, the projector should not be installed in any other way except desktop and ceiling mount positions. Otherwise lamp life could decrease dramatically, and may lead to other unpredictable damage. Allow at least 50 cm (16.69 inch) clearance around the exhaust vent. Ensure that the intake vents do not recycle hot air from...
Page 5
— iv — Power Safety Only use the supplied power cord. Do not place anything on the power cord. Place the power cord where it will not be in the way of foot traffic. Remove the batteries from the remote control when storing or not in use for a prolonged period. Replacing the Lamp Replacing the lamp can be hazardous if done incorrectly. See Replacing the Projection Lamp on page 43 for clear and safe instructions for this procedure. Before replacing the lamp: Unplug the power cord. Allow...
Page 6
Table of Contents GETTING STARTED .............................................................................................................................................. 1 PACKING CHECKLIST ............................................................................................................................................. 1 VIEWS OF PROJECTOR PARTS ................................................................................................................................ 2...
Page 7
SPECIFICATIONS ................................................................................................................................................ 53 SPECIFICATIONS .................................................................................................................................................. 53 PROJECTION DISTANCE VS. PROJECTION SIZE (XGA) ........................................................................................... 54 Projection Distance and Size...
Page 8
— 1 — GETTING STARTED Packing Checklist Carefully unpack the projector and check that the following items are included: DLP PROJECTOR WITH LENS CAP REMOTE CONTROL (BATTERIES NOT INCLUDED) VGA CABLE POWER CORD CD-ROM (THIS USER’S MANUAL) QUICK START GUIDE SAFETY & WARRANTY BOOKLET Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work. It is recommended that you keep the original packing material in case you ever need to...
Page 9
— 2 — Views of Projector Parts Front-right View ITEM LABEL DESCRIPTION SEE PAGE 1. IR receiver Receive IR signal from remote control. 2. Lens Projection Lens. 3. Focus ring Focuses the projected image. 15 4. Zoom ring Enlarges the projected image. 5. Function keys See Top view—On-screen Display (OSD) buttons and LEDsK 3 Important: Do not block ventilation openings. Locate the projector in a well-ventilated area without obstructions to intake or exhaust vents. Do not place the...
Page 10
— 3 — Top view—On-screen Display (OSD) buttons and LEDs ITEM LABEL DESCRIPTION SEE PAGE 1. Menu Open and exit OSD menus. 16 2. ◄ / VOi- Navigate and change settings in the OSaK Quick Menu – For Volume 3. Navigates the OSD. Quick Menu – For Keystone 4. Enter or confirm highlighted OSD menu item. 5. SOURCE Enter the Source menu. 6. VOL+ / ► Navigate and change settings in the OSaK Quick Menu – For Volume 7. RE-SYNC Automatically synchronizes the projector to the input source. 8....